?? main_mcbsp1.c
字號:
/*
* Copyright (C) 2003 Texas Instruments Incorporated
* All Rights Reserved
*/
/*
*---------main_mcbsp1.c---------
*
* mcbsp1 Example configures the serial port for digital loopback mode.
* We then use the CPU to write/read from the port. In loopback mode, we
* should read back the same value as written, which is checked for in a loop
*/
#include <stdio.h>
#include <csl.h>
#include <csl_mcbsp.h>
/* create a config structure for digital loopback mode */
static MCBSP_Config ConfigLoopback = {
/* Serial Port Control Register (SPCR) */
MCBSP_SPCR_RMK(
MCBSP_SPCR_FREE_YES, /* Serial clock free running mode(FREE)
MCBSP_SPCR_FREE_NO - During emulation halt,SOFT bit
determines operation of McBSP.
MCBSP_SPCR_FREE_YES - During emulation halt, serial
clocks continue to run. */
MCBSP_SPCR_SOFT_YES, /* Serial clock emulation mode(SOFT)
MCBSP_SPCR_SOFT_NO - In conjunction with FREE = 0,
serial port clock stops immediately during
emulation halt,thus aborting any transmissions.
MCBSP_SPCR_SOFT_YES - In conjunction with FREE = 0,
during emulation halt, serial port clock stops
after completion of current transmission. */
MCBSP_SPCR_FRST_YES, /* Frame sync generator reset(FRST)
MCBSP_SPCR_FRST_YES /MCBSP_SPCR_FRST_0 - Frame sync
generation logic is reset.
MCBSP_SPCR_FRST_NO /MCBSP_SPCR_FRST_1 - Frame sync
signal is generated after eight CLKG clocks. */
MCBSP_SPCR_GRST_YES, /* Sample rate generator reset(GRST)
MCBSP_SPCR_GRST_YES /MCBSP_SPCR_GRST_0 - Reset
MCBSP_SPCR_GRST_NO /MCBSP_SPCR_GRST_1 -Out of reset*/
MCBSP_SPCR_XINTM_XRDY,/* Transmit interrupt mode(XINTM)
MCBSP_SPCR_XINTM_XRDY - XINT driven by XRDY
MCBSP_SPCR_XINTM_EOS - XINT generated by
end-of-subframe in multichannel operation
MCBSP_SPCR_XINTM_FRM - XINT generated by a new frame
synchronization
MCBSP_SPCR_XINTM_XSYNCERR - XINT generated by XSYNCERR
*/
MCBSP_SPCR_XSYNCERR_NO,/* Transmit synchronization error
MCBSP_SPCR_XSYNCERR_NO /MCBSP_SPCR_XSYNCERR_0 - No
frame synchronization error
MCBSP_SPCR_XSYNCERR_YES /MCBSP_SPCR_XSYNCERR_1 - Frame
synchronization error detected by McBSP */
MCBSP_SPCR_XRST_YES, /* Transmitter reset(XRST). This resets or enables
transmitter.
MCBSP_SPCR_XRST_YES /MCBSP_SPCR_XRST_0 - Serial port
transmitter is disabled and is in reset state.
MCBSP_SPCR_XRST_NO /MCBSP_SPCR_XRST_1 - Serial port
transmitter is enabled. */
MCBSP_SPCR_DLB_ON, /* Digital loopback(DLB) mode
MCBSP_SPCR_DLB_OFF - DLB Disabled
MCBSP_SPCR_DLB_ON - DLB Enabled */
MCBSP_SPCR_RJUST_RZF,/*Receive data sign-extension and justification mode(RJUST)
MCBSP_SPCR_RJUST_RZF - Right-justify and zero-fill
MSBs in DRR.
MCBSP_SPCR_RJUST_RSE - Right-justify and sign-extend
MSBs in DRR.
MCBSP_SPCR_RJUST_LZF - Left-justify and zero-fill
LSBs in DRR. */
MCBSP_SPCR_CLKSTP_DISABLE,/* Clock stop(CLKSTP) mode
MCBSP_SPCR_CLKSTP_DISABLE - Disabled. Normal
clocking enabled for non-SPI mode.
MCBSP_SPCR_CLKSTP_NODELAY -Clock starts without delay.
MCBSP_SPCR_CLKSTP_DELAY - Clock starts with delay.*/
MCBSP_SPCR_DXENA_OFF,/* DX Enabler(DXENA) -Extra delay for DX turn-on time.
Only first bit of data is delayed.
MCBSP_SPCR_DXENA_OFF - DX enabler is off.
MCBSP_SPCR_DXENA_ON - DX enabler is on. */
MCBSP_SPCR_RINTM_RRDY,/* Receive interrupt(RINT) mode
MCBSP_SPCR_RINTM_RRDY - RINT driven by RRDY
MCBSP_SPCR_RINTM_EOS - RINT generated by
end-of-subframe in multichannel operation
MCBSP_SPCR_RINTM_FRM - RINT generated by a new frame
synchronization
MCBSP_SPCR_RINTM_RSYNCERR -RINT generated by RSYNCERR*/
MCBSP_SPCR_RSYNCERR_NO,/* Receive synchronization error(RSYNCERR)
MCBSP_SPCR_RSYNCERR_NO /MCBSP_SPCR_RSYNCERR_0 - No
frame synchronization error
MCBSP_SPCR_RSYNCERR_YES /MCBSP_SPCR_RSYNCERR_1 - Frame
synchronization error detected by McBSP */
MCBSP_SPCR_RRST_YES /* Receiver reset(RRST). This resets or enables
receiver.
MCBSP_SPCR_RRST_YES /MCBSP_SPCR_RRST_0 - Serial
port receiver is disabled and is in reset state.
MCBSP_SPCR_RRST_NO /MCBSP_SPCR_RRST_1 - Serial
port receiver is enabled. */
),
/* Receive Control Register (RCR) */
MCBSP_RCR_RMK(
MCBSP_RCR_RPHASE_SINGLE, /* Receive phases
MCBSP_RCR_RPHASE_SINGLE - Single phase frame
MCBSP_RCR_RPHASE_DUAL - Dual phase frame */
MCBSP_RCR_RFRLEN2_OF(0), /* Receive frame length in phase 2(RFRLEN2)
000 0000b: 1 word per phase
000 0001b: 2 words per phase
. . . . . . . . . . . .
111 1111b: 128 words per phase */
MCBSP_RCR_RWDLEN2_8BIT,/* Receive element length in phase 2(RWDLEN2)
MCBSP_RCR_RWDLEN2_8BIT - 8 bits
MCBSP_RCR_RWDLEN2_12BIT - 12 bits
MCBSP_RCR_RWDLEN2_16BIT - 16 bits
MCBSP_RCR_RWDLEN2_20BIT - 20 bits
MCBSP_RCR_RWDLEN2_24BIT - 24 bits
MCBSP_RCR_RWDLEN2_32BIT - 32 bits */
MCBSP_RCR_RCOMPAND_MSB,/* Receive companding mode (RCOMPAND)
MCBSP_RCR_RCOMPAND_MSB - No companding.Data
transfer starts with MSB first.
MCBSP_RCR_RCOMPAND_8BITLSB - No companding,
8-bit data. Transfer starts with LSB first.
Applicable to 8-bit data or 32-bit data in
data reversal mode.
MCBSP_RCR_RCOMPAND_ULAW - Compand using m-law for
receive data. Applicable to 8-bit data only
MCBSP_RCR_RCOMPAND_ALAW - Compand using A-law for
receive data. Applicable to 8-bit data only */
MCBSP_RCR_RFIG_YES, /* Receive frame ignore(RFIG)
MCBSP_RCR_RFIG_NO - Unexpected receive frame
synchronization pulses restart the transfer.
MCBSP_RCR_RFIG_YES - Unexpected receive frame
synchronization pulses are ignored. */
MCBSP_RCR_RDATDLY_0BIT,/* Receive data delay(RDATDLY)
MCBSP_RCR_RDATDLY_0BIT - 0 bit data delay
MCBSP_RCR_RDATDLY_1BIT - 1 bit data delay
MCBSP_RCR_RDATDLY_2BIT - 2 bit data delay */
MCBSP_RCR_RFRLEN1_OF(0), /* Receive frame length in phase 1(RFRLEN1)
000 0000b: 1 word per phase
000 0001b: 2 words per phase
. . . . . . . . . . . .
111 1111b: 128 words per phase */
MCBSP_RCR_RWDLEN1_32BIT,/* Receive element length in phase 1(RWDLEN1)
MCBSP_RCR_RWDLEN1_8BIT - 8 bits
MCBSP_RCR_RWDLEN1_12BIT - 12 bits
MCBSP_RCR_RWDLEN1_16BIT - 16 bits
MCBSP_RCR_RWDLEN1_20BIT - 20 bits
MCBSP_RCR_RWDLEN1_24BIT - 24 bits
MCBSP_RCR_RWDLEN1_32BIT - 32 bits */
MCBSP_RCR_RWDREVRS_DISABLE/* Receive 32-bit bit reversal feature.(RWDREVRS)
MCBSP_RCR_RWDREVRS_DISABLE -32 bit reversal disabled
MCBSP_RCR_RWDREVRS_ENABLE -32 bit reversal enabled.
32-bit data is received LSB first.
RWDLEN should be set for 32-bit operation.
RCOMPAND should be set to 01b else operation
is undefined. */
),
/* Transmit Control Register (XCR) */
MCBSP_XCR_RMK(
MCBSP_XCR_XPHASE_SINGLE,/* Transmit phases
MCBSP_XCR_XPHASE_SINGLE - Single phase frame
MCBSP_XCR_XPHASE_DUAL - Dual phase frame */
MCBSP_XCR_XFRLEN2_OF(0),/* Transmit frame length in phase 2(XFRLEN2)
000 0000b: 1 word per phase
000 0001b: 2 words per phase
. . . . . . . . . . . .
111 1111b: 128 words per phase */
MCBSP_XCR_XWDLEN2_8BIT, /* Transmit element length in phase 2
MCBSP_XCR_XWDLEN2_8BIT - 8 bits
MCBSP_XCR_XWDLEN2_12BIT - 12 bits
MCBSP_XCR_XWDLEN2_16BIT - 16 bits
MCBSP_XCR_XWDLEN2_20BIT - 20 bits
MCBSP_XCR_XWDLEN2_24BIT - 24 bits
MCBSP_XCR_XWDLEN2_32BIT - 32 bits */
MCBSP_XCR_XCOMPAND_MSB, /* Transmit companding mode(XCOMPAND)
MCBSP_XCR_XCOMPAND_MSB - No companding. Data
transfer starts with MSB first.
MCBSP_XCR_XCOMPAND_8BITLSB - No companding, 8-bit
data. Transfer starts with LSB first.
Applicable to 8-bit data,or 32-bit data in
data reversal mode.
MCBSP_XCR_XCOMPAND_ULAW - Compand using m-law
for receive data.Applicable to 8-bit data only.
MCBSP_XCR_XCOMPAND_ALAW - Compand using A-law for
receive data.Applicable to 8-bit data only. */
MCBSP_XCR_XFIG_YES, /* Transmit frame ignore(XFIG)
MCBSP_XCR_XFIG_NO - Unexpected transmit frame
synchronization pulses restart the transfer.
MCBSP_XCR_XFIG_YES - Unexpected transmit frame
synchronization pulses are ignored. */
MCBSP_XCR_XDATDLY_0BIT, /* Transmit data delay(XDATDLY)
MCBSP_XCR_XDATDLY_0BIT - 0 bit data delay
MCBSP_XCR_XDATDLY_1BIT - 1 bit data delay
MCBSP_XCR_XDATDLY_2BIT - 2 bit data delay */
MCBSP_XCR_XFRLEN1_OF(0), /* Transmit frame length in phase 1(XFRLEN1)
000 0000b: 1 word per phase
000 0001b: 2 words per phase
. . . . . . . . . . . .
111 1111b: 128 words per phase */
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -