;*******************************************************************************
;   MSP430F20x2 Demo - ADC10, Sample A1, 1.5V Ref, Set P1.0 if A1 > 0.2V
;
;   Description: A single sample is made on A1 with reference to internal
;   1.5V Vref. Software sets ADC10SC to start sample and conversion - ADC10SC
;   automatically cleared at EOC. ADC10 internal oscillator times sample (16x)
;   and conversion. In Mainloop MSP430 waits in LPM0 to save power until ADC10
;   conversion complete, ADC10_ISR will force exit from any LPMx in Mainloop on
;   reti. If A1 > 0.2V, P1.0 set, else reset.
;
;                MSP430F20x2
;             -----------------
;         /|\|              XIN|-
;          | |                 |
;          --|RST          XOUT|-
;            |                 |
;        >---|P1.1/A1      P1.0|--> LED
;
;   L. Westlund
;   Texas Instruments Inc.
;   May 2006
;   Built with IAR Embedded Workbench Version: 3.41A
;*******************************************************************************
#include "msp430x20x2.h"
;-------------------------------------------------------------------------------
            RSEG    CSTACK                  ; Define stack segment
;-------------------------------------------------------------------------------
            RSEG    CODE                    ; Assemble to Flash memory
;-------------------------------------------------------------------------------
RESET       mov.w   #SFE(CSTACK),SP         ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop WDT
SetupADC10  mov.w   #SREF_1+ADC10SHT_2+REFON+ADC10ON+ADC10IE,&ADC10CTL0;
            mov.w   #30,&TACCR0             ; Delay to allow Ref to settle
            bis.w   #CCIE,&TACCTL0          ; Compare-mode interrupt.
            mov.w   #TACLR+MC_1+TASSEL_2,&TACTL; up mode, SMCLK
            bis.w   #LPM0+GIE,SR            ; Enter LPM0, enable interrupts
            bic.w   #CCIE,&TACCTL0          ; Disable timer interrupt
            dint
            bis.b   #02h,&ADC10AE0          ; P1.1 ADC10 option select
            mov.w   #INCH_1, &ADC10CTL1     ; A1 input
SetupP1     bis.b   #001h,&P1DIR            ; P1.0 output

Mainloop    bis.w   #ENC+ADC10SC,&ADC10CTL0 ; Start sampling/conversion
            bis.w   #CPUOFF+GIE,SR          ; LPM0, ADC12 ISR will force exit
            bic.b   #01h,&P1OUT             ; P1.0 = 0
            cmp.w   #088h,&ADC10MEM         ; ADC10MEM = A1 > 0.2V?
            jlo     Mainloop                ; Again
            bis.b   #01h,&P1OUT             ; P1.0 = 1
            jmp     Mainloop                ; Again

;-------------------------------------------------------------------------------
TA0_ISR;    ISR for TACCR0
;-------------------------------------------------------------------------------
            clr.w   &TACTL                  ; Clear Timer_A control registers
            bic.w   #LPM0,0(SP)             ; Exit LPM0, interrupts enabled
            reti                            ;
;-------------------------------------------------------------------------------
ADC10_ISR;  Exit LPM0 on reti
;-------------------------------------------------------------------------------
            bic.w   #LPM0,0(SP)             ; Exit LPM0, interrupts enabled
            reti                            ;
;-------------------------------------------------------------------------------
            COMMON  INTVEC                  ; Interrupt Vectors
;-------------------------------------------------------------------------------
            ORG     ADC10_VECTOR            ; ADC10 Vector
            DW      ADC10_ISR
            ORG     TIMERA0_VECTOR          ; Timer_A0 Vector
            DW      TA0_ISR
            ORG     RESET_VECTOR            ; POR, ext. Reset
            DW      RESET
            END