4A         Amount of memory above 1M found and verified.
             Going for BIOS ROM data area check.

  4B         BIOS ROM data area check over. Going to check <ESC>
             and to clear memory below 1M for soft reset.

  4C         Memory below 1M cleared.        (SOFT RESET)
             Going to clear memory above 1M.

  4D         Memory above 1M cleared.        (SOFT RESET)
             Going to save the memory size.

  4E         Memory test started.         (NO SOFT RESET)
             About to display the first 64k memory test.

  4F         Memory size display started. This will be updated during
             memory test. Going for sequential and random memory test.

  50         Memory test below 1M complete.
             Going to adjust memory size for relocation/ shadow.

  51         Memory size adjusted due to relocation/ shadow.
             Memory test above 1M to follow.

  52         Memory test above 1M complete.
             Going to prepare to go back to real mode.

  53         CPU registers are saved including memory size.
             Going to enter in real mode.

  54         Shutdown successfull, CPU in real mode. Going to restore
             registers saved during preparation for shutdown.

  55         Registers restored.
             Going to disable gate A20 address line.

  56         A20 address line disable successful.
             BIOS ROM data area about to be checked.

  57         BIOS ROM data area check halfway.
             BIOS ROM data area check to be complete.

  58         BIOS ROM data area check over.
             Going to clear Hit <ESC> message.

  59         Hit <ESC> message cleared. <WAIT...> message displayed.
             About to start DMA and interrupt controller test.

  60         DMA page register test passed.
             About to verify from display memory.

  61         Display memory verification over.
             About to go for DMA #1 base register test.

  62         DMA #1 base register test passed.
             About to go for DMA #2 base register test.

  63         DMA #2 base register test passed.
             About to go for BIOS ROM data area check.

  64         BIOS ROM data area check halfway.
             BIOS ROM data area check to be complete.

  65         BIOS ROM data area check over.
             About to program DMA unit 1 and 2.

  66         DMA unit 1 and 2 programming over.
             About to initialize 8259 interrupt controller.

  67         8259 initialization over.
             About to start keyboard test.

  80         Keyboard test started. clearing output buffer, checking
             for stuck key, About to issue keyboard reset command.

  81         Keyboard reset error/stuck key found. About to
             issue keyboard controller interface test command.

  82         Keyboard controller interface test over.
             About to write command byte and init circular buffer.

  83         Command byte written, Global data init done.
             About to check for lock-key.

  84         Lock-key checking over.
             About to check for memory size mismatch with CMOS.

  85         Memory size check done. About to display soft error
             and check for password or bypass setup.

  86         Password checked.
             About to do pogramming before setup.

  87         Programming before setup complete.
             Going to CMOS setup program.

  88         Returned from cmos setup program and screen is cleared.
             About to do programming after setup.

  89         Programming after setup complete.
             Going to display power on screen message.

  8A         First screen message displayed. About to display <WAIT...>
             message.

  8B         <WAIT...> message displayed.
             About to do Main and Video BIOS shadow.

  8C         Main and Video BIOS shadow successful.
             Setup options programming after cmos setup about to start.

  8D         Setup options are programmed, mouse check and init
             to be done next. 

  8E         Mouse check and initialisation complete. 
             Going for hard disk, floppy reset.

  8F         Floppy check returns that floppy is to be initialized.
             Floppy setup to follow.

  90         Floppy setup is over.
             Test for hard disk presence to be done.

  91         Hard disk presence test over.
             Hard disk setup to follow.

  92         Hard disk setup complete.
             About to go for BIOS ROM data area check.

  93         BIOS ROM data area check halfway.
             BIOS ROM data area check to be complete.

  94         BIOS ROM data area check over.
             Going to set base and extended memory size.

  95         Memory size adjusted due to mouse support, hdisk type-47.
             Going to verify from display memory.

  96         Returned after verifying from display memory.
             Going to do any init before C800 optional ROM control

  97         Any init before C800 optional ROM control is over.
             Optional ROM check and control will be done next.

  98         Optional ROM control is done. About to give control to do
             any required procesing after optional ROM returns control.

  99         Any initialization required after optional ROM test over.
             Going to setup timer data area and printer base address.

  9A         Return after setting timer and printer base address.
             Going to set the RS-232 base address.

  9B         Returned after RS-232 base address.
             Going to do any initialization before Co-processor test

  9C         Required initialization before co-processor is over.
             Going to initialize the coprocessor next.

  9D         Coprocesor initialized.
             Going to do any initialization after Co-processor test.

  9E         Initialization after co-processor test is complete.
             Going to check extd keyboard, keyboard ID and num-lock.

  9F         Extd keyboard check is done, ID flag set. num-lock on/off.
             Keyboard ID command to be issued.

  A0         Keyboard ID command issued.
             Keyboard ID flag to be reset.

  A1         Keyboard ID flag reset.
             Cache memory test to follow.

  A2         Cache memory test over.
             Going to display any soft errors.

  A3         Soft error display complete.
             Going to set the keyboard typematic rate.

  A4         Keyboard typematic rate set.
             Going to program memory wait states.

  A5         Memory wait states programming over.
             Screen to be cleared next.

  A6         Screen cleared.
             Going to enable parity and NMI.

  A7         NMI and parity enabled. Going to do any initialization
             required before giving control to optional ROM at E000.

  A8         Initialization before E000h ROM control over.
             E000h ROM to get control next.

  A9         Returned from E000h ROM control. Going to do any
             initialization required after E000h optional ROM control.

  AA         Initialization after E000h optional ROM control is over.
             Going to display the system configuration.

  00         System configuration is displayed.
             Going to give control to INT 19h boot loader.