哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌
AMI-BIOS CHECK-POINT, (C)1991 American Megatrends Inc.,All Rights Reserved
1346 Oakbrook Dr. #120. GA-30093. Phone:(404)-263-8181, Fax:(404)-263-9381
哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌哌

Beep Codes and Screen Error Messages for AMI WinBIOS
       

BEEP CODE             MESSAGE / DESCRIPTION

 1 long - 2 short     No video card found
                      (Apply only to baseboards with no onboard 
                       video controller.)

 1 long - 3 short     No Monitor connected present
                      (Apply only to baseboards with no onboard 
                       video controller.)

 1 long - x short     Video related failure
                      (Other video beep codes may exist and are tied to 
                      specific video BIOS implementations. Contact the 
                      vendor for details.)

    1                  Refresh Failure   
                       (The memory refresh circuitry is faulty.)

    2                  Parity Error      
                       (Parity error in the base memory (the first 64 KB 
                       block) of memory.)

    3                  Base 64 KB Memory Failure   
                       (Memory failure in first 64 KB.)

    4                  Timer Not Operational   
                       (A memory failure in the first 64 KB of memory, or 
                       Timer 1 is not functioning.)

    5                  Processor Error         
                       (The CPU generated an error.)

    6                  8042 - Gate A20 Failure
                       (Cannot switch to protected mode.)
    
    7                  Processor Exception     
                       (The CPU on the CPU Card generated an Interrupt
                        Error on exception interrupt.)

    8                  Display Memory Read/Write Error
                       (The system video adapter is either missing or its 
                       memory is faulty. This is not a fatal error.)

    9                  ROM Checksum Error      
                       (The ROM checksum value does not match the value 
                        encoded in WinBIOS.)

   10                  CMOS Shutdown Register Read/Write Error
                       (The shutdown register for CMOS RAM has failed.)
                                                      
   11                  Cache Memory Bad / Do Not Enable Cache
                       (The cache memory test failed. Cache memory is 
                       disabled. Do not press <Ctrl> <Alt> <Shift> <+> 
                       to enable cache memory.)

---------------------------------------------------------------------------

WinBIOS Screen Error Messages


 - 8042 GATE-A20 ERROR     
   Gate A20 on the keyboard controller (8042) is not working.

 - ADDRESS LINE SHORT!     
   Error in the address decoding circuitry.

 - DRIVE C: FAILURE        
   No response from hard disk drive C:.

 - CACHE MEMORY BAD,DO NOT ENABLE CACHE!
   Cache memory is defective.

 - CH-2 TIMER ERROR        
   An AT system has two timers. There is an error in timer2.

 - CMOS BATTERY STATE LOW  
   CMOS RAM is powered by a battery. The battery power is low. 
   Replace the battery.

 - CMOS CHECKSUM FAILURE   
   CMOS RAM checksum is different than the previous value. 
   Run WINBIOS Setup.
   
 - CMOS SYSTEM OPTIONS NOT SET
   The values stored in CMOS RAM have ben destroyed. 
   Run WINBIOS Setup.
   
 - CMOS DISPLAY TYPE MISMATCH
   The video type in CMOS RAM does not match the type detected. 
   Run WINBIOS Setup.

 - CMOS MEMORY SIZE MISMATCH
   The amount of memory found by WINBIOS is different than the 
   amount in CMOS RAM. Run WINBIOS Setup.

 - CMOS TIME AND DATE NOT SET
   Run Standard Setup to set the date and time.

 - DRIVE D: FAILURE        
   No response from hard disk drive D:.
                        
 - DISKETTE BOOT FAILURE 
   The boot diskette in drive A: cannot be used to  boot the system. 
   Use another boot diskette and follow the screen instructions.

 - DISPLAY  SWITCH NOT PROPER 
   Some systems require a video switch be set to either color or 
   monochrome. Turn the system off, set the switch properly, then power on.
   
 - DMA ERROR
   Error in the DMA controller.
 
 - DMA 1 ERROR             
   Error in the first DMA channel.

 - DMA 2 ERROR             
   Error in the second DMA channel.

 - FDD CONTROLLER FAILURE 
   BIOS cannot communicate with the floppy disk drive controller. 
   Check all appropriate connections after the system is powered down.

 - HDD CONTROLLER FAILURE
   BIOS cannot communicate with the hard disk drive controller. Check 
   all appropriate connections after the system is powered down.

 - INTR1 ERROR             
   Interrupt channel 1 failed POST.

 - INTR2 ERROR             
   Interrupt channel 2 failed POST.
                         
 - INVALID BOOT DISKETTE 
   BIOS can read the diskette in floppy drive A:,  but it cannot boot 
   the system with it. Use another boot diskette and follow the screen
   instructions.
   
 - KEYBOARD IS LOCKED ...UNLOCK IT
   The keyboard lock on the system is engaged. The system must be unlocked 
   to continue to boot.
       
 - KEYBOARD ERROR        
   The keyboard has a timing problem. Make sure a WinBIOS Keyboard 
   Controller is installed. Set Keyboard in Advanced Setup to Not Installed 
   to skip the keyboard POST routines.
                         
 - KB/INTERFACE ERROR     
   There is an error in the keyboard connector.

 - NO ROM BASIC            
   Cannot find a proper bootable sector on either drive A: or C:. 
   BIOS cannot find ROM Basic. 
 
 - OFF BOARD PARITY ERROR ADDR = (XXXX)  
   Parity error in memory installed on an adapter card in an expansion slot. 
   XXXX is the hex address where the error occurred.

 - ON BOARD PARITY ERROR ADDR = (XXXX)   
   Parity error in motherboard memory. XXXX is the hex address where 
   the error occurred.

 - PARITY ERROR ????   
   Parity error in system memory at an unknown address. 

***************************************************************************

ISA NMI MESSAGES

 - MEMORY PARITY ERROR AT XXXXX
   Memory failed. If the memory location can be determined, it is displayed 
   as xxxxx. If not, the message is Memory Parity Error ????.

 - I/O CARD PARITY ERROR AT XXXXX 
   An expansion card failed. If the address can be determined, it is 
   displayed as xxxxx. If not, the message is I/O Card Parity Error ????.

 - DMA BUS TIME-OUT   
   A device has driven the bus signal for more than 7.8 microseconds.