//--------------------------------------
//Modefied by wangfeng,2003-08-29 15:18
//For new setup menu 
//--------------------------------------


//
// DEFINITIONS
//
// #1
// *SDRAM_16Mb_Mode
//  define this to compress memory into 1x16Mb SDRAM configuration
//
// *SDRAM_32Mb_Mode
// *SDRAM_64Mb_Mode
//  for 4MB and 8MB systems
//
// #2
// *SDRAM_32BITS
//  define this for 32-bit SDRAM interface. without this definition,
//  firmware will configure the SDRAM controller to use 16-bit SDRAM
//  interface.
//
// #3
// *DVD_AUDIO
//  define this to support DVD-audio related functions.
//
//


#define VERSION_STRING      "STD-000"   //version: xxx-yyy, 20030422

//---------------------
//board parts settings
//---------------------
//#define SDRAM_16Mb_Mode       // only use 16Mb*1 SDRAM
//#define SDRAM_32Mb_Mode         // with 4MB memory
#define SDRAM_64Mb_Mode       // with 8MB memory

 
//SDRAM settings(bus width, default is 16-bits mode)
//#ifndef SDRAM_16Mb_Mode
//#define SDRAM_BUS_32BITS        // define it to use 32 bits SDRAM Bus width
//#endif


//#define AUTO_PLAY				// VCD/DVD auto play when tray-in

#ifdef AUTO_PLAY
#define DVD_SEQ_PLAY
#endif

/*
* Define Disc detect polling time
*/
#define DETECT_TIMES	0xff
#define NO_DISC_TIMES	30

/*
*  Video seting
*/
/*#define TV_YUV_OUT*/
#define S_VIDEO_OUT


/*
* ROM setting
*/
/*#define ROM_SDRAM_SHARE_BUS*/

//CD-G related
#define SUPPORT_CDG                 //define it to support CD-G

//#define TVOUT6_4DAC_ON
#ifdef TVOUT6_4DAC_ON
#define TV_USE_4_DAC
#endif

//#define TV_USE_4_DAC
//#define SCART_TV                  //define it if we support SCART TV, use GPIO-37-38-39 to control
//#define ORI_SCART_TV
//#define SCART_TV_2				//define pin151---SCART_DISPLAY; pin163---SCART_SIG  wanghaoying
 
//Upgrade setting
#define UPGRADE_FILE_NAME	{"DVDROM.BIN"}

//#define OLD_I2C_DEFINE        //define it to use GPIO-35/36 for I2C, otherwise, GPIO-0/1

#ifndef SDRAM_16Mb_Mode
//#define SUPPORT_NESGAME
//#define DVD_AUDIO
#endif


//audio DAC settings, chose one
//we prefer using audio DAC hardware config
//#define USE_DAC_RJ24        //(default setting)
//#define USE_DAC_I2S24
//#define USE_DAC_RJ16
//#define USE_DAC_I2S16
//#define USE_DAC_LJ24
//#define USE_DAC_LJ16

//only PCM1742 use software config
//#define PCM1742

//legacy audio DAC settings
//#define WM8746                      //(format:RJ24)WM8766 is pin-2-pin compatible
//#define WM8746I2S24               //(format:I2S24)
//#define WM8736                    //for AUDIO DAC WM8736 or DA1196 6 chanell
//#define AV2188
//#define CS4228
#define CS4360          //huziqin 2004-2-25 15:44 use I2C to set mode.
#if defined(CS4360)
#define	USE_DAC_I2S24
#endif

//2 channel audio DAC
//#define WM8726RJ16
//#define WM8746I2S24
//#define WM8720                    //use GPIO-17 as AUDIO_RST
//#define CS4334DAC
//#define PCM1742
//#define PCM1606
//#define PCM1720
//#define PCM1723

//Audio channel connector(RCA connector)setting, Jeff 20020520
//We assign connectors to the following index, Lm(0), Rm(1), L(2), R(3), Ls(4), Rs(5), C(6), SFE(7)
//2-3-4-5-6-7 map to DAC OUT0L-OUT0R-OUT1L-OUT1R-OUT2L-OUT2R
#define DACOUTLm        6//0
#define DACOUTRm        7//1
#define DACOUT0L        0//2
#define DACOUT0R        1//3
#define DACOUT1L        2//4
#define DACOUT1R        3//5
#define DACOUT2L        4//6
#define DACOUT2R        5//7


#define DAC_INVERT      1           //dac polarity 0 (untouch) or 1 (inverted)

//#define USE_A19_AS_GPIO_MUTE
#define USE_AUD3_AS_GPIO_MUTE
#ifdef USE_AUD3_AS_GPIO_MUTE
#define LOW_MUTE
#endif//USE_AUD3_AS_GPIO_MUTE

//#define SUPPORT_TESTSPK  benson add 2004/7/15 05:10