?? eth_top.v
字號:
`include "eth_defines.v"
`include "timescale.v"
module eth_top
(
// WISHBONE common
wb_clk_i, wb_rst_i, wb_dat_i, wb_dat_o,
// WISHBONE slave
wb_adr_i, wb_sel_i, wb_we_i, wb_cyc_i, wb_stb_i, wb_ack_o, wb_err_o,
// WISHBONE master
m_wb_adr_o, m_wb_sel_o, m_wb_we_o,
m_wb_dat_o, m_wb_dat_i, m_wb_cyc_o,
m_wb_stb_o, m_wb_ack_i, m_wb_err_i,
`ifdef ETH_WISHBONE_B3
m_wb_cti_o, m_wb_bte_o,
`endif
//TX
mtx_clk_pad_i, mtxd_pad_o, mtxen_pad_o, mtxerr_pad_o,
//RX
mrx_clk_pad_i, mrxd_pad_i, mrxdv_pad_i, mrxerr_pad_i, mcoll_pad_i, mcrs_pad_i,
// MIIM
mdc_pad_o, md_pad_i, md_pad_o, md_padoe_o,
int_o
// Bist
`ifdef ETH_BIST
,
// debug chain signals
scanb_rst, // bist scan reset
scanb_clk, // bist scan clock
scanb_si, // bist scan serial in
scanb_so, // bist scan serial out
scanb_en // bist scan shift enable
`endif
);
parameter Tp = 1;
// WISHBONE common
input wb_clk_i; // WISHBONE clock
input wb_rst_i; // WISHBONE reset
input [31:0] wb_dat_i; // WISHBONE data input
output [31:0] wb_dat_o; // WISHBONE data output
output wb_err_o; // WISHBONE error output
// WISHBONE slave
input [11:2] wb_adr_i; // WISHBONE address input
input [3:0] wb_sel_i; // WISHBONE byte select input
input wb_we_i; // WISHBONE write enable input
input wb_cyc_i; // WISHBONE cycle input
input wb_stb_i; // WISHBONE strobe input
output wb_ack_o; // WISHBONE acknowledge output
// WISHBONE master
output [31:0] m_wb_adr_o;
output [3:0] m_wb_sel_o;
output m_wb_we_o;
input [31:0] m_wb_dat_i;
output [31:0] m_wb_dat_o;
output m_wb_cyc_o;
output m_wb_stb_o;
input m_wb_ack_i;
input m_wb_err_i;
`ifdef ETH_WISHBONE_B3
output [2:0] m_wb_cti_o; // Cycle Type Identifier
output [1:0] m_wb_bte_o; // Burst Type Extension
`endif
// Tx
input mtx_clk_pad_i; // Transmit clock (from PHY)
output [3:0] mtxd_pad_o; // Transmit nibble (to PHY)
output mtxen_pad_o; // Transmit enable (to PHY)
output mtxerr_pad_o; // Transmit error (to PHY)
// Rx
input mrx_clk_pad_i; // Receive clock (from PHY)
input [3:0] mrxd_pad_i; // Receive nibble (from PHY)
input mrxdv_pad_i; // Receive data valid (from PHY)
input mrxerr_pad_i; // Receive data error (from PHY)
// Common Tx and Rx
input mcoll_pad_i; // Collision (from PHY)
input mcrs_pad_i; // Carrier sense (from PHY)
// MII Management interface
input md_pad_i; // MII data input (from I/O cell)
output mdc_pad_o; // MII Management data clock (to PHY)
output md_pad_o; // MII data output (to I/O cell)
output md_padoe_o; // MII data output enable (to I/O cell)
output int_o; // Interrupt output
// Bist
`ifdef ETH_BIST
input scanb_rst; // bist scan reset
input scanb_clk; // bist scan clock
input scanb_si; // bist scan serial in
output scanb_so; // bist scan serial out
input scanb_en; // bist scan shift enable
`endif
wire [7:0] r_ClkDiv;
wire r_MiiNoPre;
wire [15:0] r_CtrlData;
wire [4:0] r_FIAD;
wire [4:0] r_RGAD;
wire r_WCtrlData;
wire r_RStat;
wire r_ScanStat;
wire NValid_stat;
wire Busy_stat;
wire LinkFail;
wire [15:0] Prsd; // Read Status Data (data read from the PHY)
wire WCtrlDataStart;
wire RStatStart;
wire UpdateMIIRX_DATAReg;
wire TxStartFrm;
wire TxEndFrm;
wire TxUsedData;
wire [7:0] TxData;
wire TxRetry;
wire TxAbort;
wire TxUnderRun;
wire TxDone;
wire [5:0] CollValid;
reg WillSendControlFrame_sync1;
reg WillSendControlFrame_sync2;
reg WillSendControlFrame_sync3;
reg RstTxPauseRq;
reg TxPauseRq_sync1;
reg TxPauseRq_sync2;
reg TxPauseRq_sync3;
reg TPauseRq;
// Connecting Miim module
eth_miim miim1
(
.Clk(wb_clk_i), .Reset(wb_rst_i), .Divider(r_ClkDiv),
.NoPre(r_MiiNoPre), .CtrlData(r_CtrlData), .Rgad(r_RGAD),
.Fiad(r_FIAD), .WCtrlData(r_WCtrlData), .RStat(r_RStat),
.ScanStat(r_ScanStat), .Mdi(md_pad_i), .Mdo(md_pad_o),
.MdoEn(md_padoe_o), .Mdc(mdc_pad_o), .Busy(Busy_stat),
.Prsd(Prsd), .LinkFail(LinkFail), .Nvalid(NValid_stat),
.WCtrlDataStart(WCtrlDataStart), .RStatStart(RStatStart), .UpdateMIIRX_DATAReg(UpdateMIIRX_DATAReg)
);
wire RegCs; // Connected to registers
wire [31:0] RegDataOut; // Multiplexed to wb_dat_o
wire r_RecSmall; // Receive small frames
wire r_LoopBck; // Loopback
wire r_TxEn; // Tx Enable
wire r_RxEn; // Rx Enable
wire MRxDV_Lb; // Muxed MII receive data valid
wire MRxErr_Lb; // Muxed MII Receive Error
wire [3:0] MRxD_Lb; // Muxed MII Receive Data
wire Transmitting; // Indication that TxEthMAC is transmitting
wire r_HugEn; // Huge packet enable
wire r_DlyCrcEn; // Delayed CRC enabled
wire [15:0] r_MaxFL; // Maximum frame length
wire [15:0] r_MinFL; // Minimum frame length
wire ShortFrame;
wire DribbleNibble; // Extra nibble received
wire ReceivedPacketTooBig; // Received packet is too big
wire [47:0] r_MAC; // MAC address
wire LoadRxStatus; // Rx status was loaded
wire [31:0] r_HASH0; // HASH table, lower 4 bytes
wire [31:0] r_HASH1; // HASH table, upper 4 bytes
wire [7:0] r_TxBDNum; // Receive buffer descriptor number
wire [6:0] r_IPGT; //
wire [6:0] r_IPGR1; //
wire [6:0] r_IPGR2; //
wire [5:0] r_CollValid; //
wire [15:0] r_TxPauseTV; // Transmit PAUSE value
wire r_TxPauseRq; // Transmit PAUSE request
wire [3:0] r_MaxRet; //
wire r_NoBckof; //
wire r_ExDfrEn; //
wire TX_BD_NUM_Wr; // Write enable that writes RX_BD_NUM to the registers.
wire r_TxFlow; // Tx flow control enable
wire r_IFG; // Minimum interframe gap for incoming packets
wire TxB_IRQ; // Interrupt Tx Buffer
wire TxE_IRQ; // Interrupt Tx Error
wire RxB_IRQ; // Interrupt Rx Buffer
wire RxE_IRQ; // Interrupt Rx Error
wire Busy_IRQ; // Interrupt Busy (lack of buffers)
wire DWord;
wire BDAck;
wire [31:0] BD_WB_DAT_O; // wb_dat_o that comes from the Wishbone module (for buffer descriptors read/write)
wire BDCs; // Buffer descriptor CS
wire CsMiss; // When access to the address between 0x800 and 0xfff occurs, acknowledge is set
// but data is not valid.
wire temp_wb_ack_o;
wire [31:0] temp_wb_dat_o;
wire temp_wb_err_o;
`ifdef ETH_REGISTERED_OUTPUTS
reg temp_wb_ack_o_reg;
reg [31:0] temp_wb_dat_o_reg;
reg temp_wb_err_o_reg;
`endif
assign DWord = &wb_sel_i;
assign RegCs = wb_stb_i & wb_cyc_i & DWord & ~wb_adr_i[11] & ~wb_adr_i[10]; // 0x0 - 0x3FF
assign BDCs = wb_stb_i & wb_cyc_i & DWord & ~wb_adr_i[11] & wb_adr_i[10]; // 0x400 - 0x7FF
assign CsMiss = wb_stb_i & wb_cyc_i & DWord & wb_adr_i[11]; // 0x800 - 0xfFF
assign temp_wb_ack_o = RegCs | BDAck;
assign temp_wb_dat_o = (RegCs & ~wb_we_i)? RegDataOut : BD_WB_DAT_O;
assign temp_wb_err_o = wb_stb_i & wb_cyc_i & (~DWord | CsMiss);
`ifdef ETH_REGISTERED_OUTPUTS
assign wb_ack_o = temp_wb_ack_o_reg;
assign wb_dat_o[31:0] = temp_wb_dat_o_reg;
assign wb_err_o = temp_wb_err_o_reg;
`else
assign wb_ack_o = temp_wb_ack_o;
assign wb_dat_o[31:0] = temp_wb_dat_o;
assign wb_err_o = temp_wb_err_o;
`endif
`ifdef ETH_REGISTERED_OUTPUTS
always @ (posedge wb_clk_i or posedge wb_rst_i)
begin
if(wb_rst_i)
begin
temp_wb_ack_o_reg <=#Tp 1'b0;
temp_wb_dat_o_reg <=#Tp 32'h0;
temp_wb_err_o_reg <=#Tp 1'b0;
end
else
begin
temp_wb_ack_o_reg <=#Tp temp_wb_ack_o & ~temp_wb_ack_o_reg;
temp_wb_dat_o_reg <=#Tp temp_wb_dat_o;
temp_wb_err_o_reg <=#Tp temp_wb_err_o & ~temp_wb_err_o_reg;
end
end
`endif
// Connecting Ethernet registers
eth_registers ethreg1
(
.DataIn(wb_dat_i), .Address(wb_adr_i[9:2]), .Rw(wb_we_i),
.Cs(RegCs), .Clk(wb_clk_i), .Reset(wb_rst_i),
.DataOut(RegDataOut), .r_RecSmall(r_RecSmall),
.r_Pad(r_Pad), .r_HugEn(r_HugEn), .r_CrcEn(r_CrcEn),
.r_DlyCrcEn(r_DlyCrcEn), .r_FullD(r_FullD),
.r_ExDfrEn(r_ExDfrEn), .r_NoBckof(r_NoBckof), .r_LoopBck(r_LoopBck),
.r_IFG(r_IFG), .r_Pro(r_Pro), .r_Iam(),
.r_Bro(r_Bro), .r_NoPre(r_NoPre), .r_TxEn(r_TxEn),
.r_RxEn(r_RxEn), .Busy_IRQ(Busy_IRQ), .RxE_IRQ(RxE_IRQ),
.RxB_IRQ(RxB_IRQ), .TxE_IRQ(TxE_IRQ), .TxB_IRQ(TxB_IRQ),
.r_IPGT(r_IPGT),
.r_IPGR1(r_IPGR1), .r_IPGR2(r_IPGR2), .r_MinFL(r_MinFL),
.r_MaxFL(r_MaxFL), .r_MaxRet(r_MaxRet), .r_CollValid(r_CollValid),
.r_TxFlow(r_TxFlow), .r_RxFlow(r_RxFlow), .r_PassAll(r_PassAll),
.r_MiiNoPre(r_MiiNoPre), .r_ClkDiv(r_ClkDiv),
.r_WCtrlData(r_WCtrlData), .r_RStat(r_RStat), .r_ScanStat(r_ScanStat),
.r_RGAD(r_RGAD), .r_FIAD(r_FIAD), .r_CtrlData(r_CtrlData),
.NValid_stat(NValid_stat), .Busy_stat(Busy_stat),
.LinkFail(LinkFail), .r_MAC(r_MAC), .WCtrlDataStart(WCtrlDataStart),
.RStatStart(RStatStart), .UpdateMIIRX_DATAReg(UpdateMIIRX_DATAReg), .Prsd(Prsd),
.r_TxBDNum(r_TxBDNum), .TX_BD_NUM_Wr(TX_BD_NUM_Wr), .int_o(int_o),
.r_HASH0(r_HASH0), .r_HASH1(r_HASH1), .r_TxPauseRq(r_TxPauseRq),
.r_TxPauseTV(r_TxPauseTV), .RstTxPauseRq(RstTxPauseRq), .TxCtrlEndFrm(TxCtrlEndFrm),
.StartTxDone(StartTxDone), .TxClk(mtx_clk_pad_i), .RxClk(mrx_clk_pad_i),
.SetPauseTimer(SetPauseTimer)
);
wire [7:0] RxData;
wire RxValid;
wire RxStartFrm;
wire RxEndFrm;
wire RxAbort;
wire WillTransmit; // Will transmit (to RxEthMAC)
wire ResetCollision; // Reset Collision (for synchronizing collision)
wire [7:0] TxDataOut; // Transmit Packet Data (to TxEthMAC)
wire WillSendControlFrame;
wire ReceiveEnd;
wire ReceivedPacketGood;
wire ReceivedLengthOK;
wire InvalidSymbol;
wire LatchedCrcError;
wire RxLateCollision;
wire [3:0] RetryCntLatched;
wire [3:0] RetryCnt;
wire StartTxAbort;
wire MaxCollisionOccured;
wire RetryLimit;
wire StatePreamble;
wire [1:0] StateData;
// Connecting MACControl
eth_maccontrol maccontrol1
(
.MTxClk(mtx_clk_pad_i), .TPauseRq(TPauseRq),
.TxPauseTV(r_TxPauseTV), .TxDataIn(TxData),
.TxStartFrmIn(TxStartFrm), .TxEndFrmIn(TxEndFrm),
.TxUsedDataIn(TxUsedDataIn), .TxDoneIn(TxDoneIn),
.TxAbortIn(TxAbortIn), .MRxClk(mrx_clk_pad_i),
.RxData(RxData), .RxValid(RxValid),
.RxStartFrm(RxStartFrm), .RxEndFrm(RxEndFrm),
.ReceiveEnd(ReceiveEnd), .ReceivedPacketGood(ReceivedPacketGood),
.TxFlow(r_TxFlow),
.RxFlow(r_RxFlow), .DlyCrcEn(r_DlyCrcEn),
.MAC(r_MAC), .PadIn(r_Pad | PerPacketPad),
.PadOut(PadOut), .CrcEnIn(r_CrcEn | PerPacketCrcEn),
.CrcEnOut(CrcEnOut), .TxReset(wb_rst_i),
.RxReset(wb_rst_i), .ReceivedLengthOK(ReceivedLengthOK),
.TxDataOut(TxDataOut), .TxStartFrmOut(TxStartFrmOut),
.TxEndFrmOut(TxEndFrmOut), .TxUsedDataOut(TxUsedData),
.TxDoneOut(TxDone), .TxAbortOut(TxAbort),
.WillSendControlFrame(WillSendControlFrame), .TxCtrlEndFrm(TxCtrlEndFrm),
.ReceivedPauseFrm(ReceivedPauseFrm), .ControlFrmAddressOK(ControlFrmAddressOK),
.SetPauseTimer(SetPauseTimer),
.RxStatusWriteLatched_sync2(RxStatusWriteLatched_sync2), .r_PassAll(r_PassAll)
);
wire TxCarrierSense; // Synchronized CarrierSense (to Tx clock)
wire Collision; // Synchronized Collision
reg CarrierSense_Tx1;
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -