/* Name: usbdrv.c * Project: AVR USB driver * Author: Christian Starkjohann * Creation Date: 2004-12-29 * Tabsize: 4 * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH * License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt) * This Revision: $Id: usbdrv.c 350 2007-06-13 11:43:16Z cs $ */#include "iarcompat.h"#ifndef __IAR_SYSTEMS_ICC__#   include <avr/io.h>#   include <avr/pgmspace.h>#endif#include "usbdrv.h"#include "oddebug.h"/*General Description:This module implements the C-part of the USB driver. See usbdrv.h for adocumentation of the entire driver.*/#ifndef IAR_SECTION#define IAR_SECTION(arg)#define __no_init#endif/* The macro IAR_SECTION is a hack to allow IAR-cc compatibility. On gcc, it * is defined to nothing. __no_init is required on IAR. *//* ------------------------------------------------------------------------- *//* raw USB registers / interface to assembler code: */uchar usbRxBuf[2*USB_BUFSIZE];  /* raw RX buffer: PID, 8 bytes data, 2 bytes CRC */uchar       usbInputBufOffset;  /* offset in usbRxBuf used for low level receiving */uchar       usbDeviceAddr;      /* assigned during enumeration, defaults to 0 */uchar       usbNewDeviceAddr;   /* device ID which should be set after status phase */uchar       usbConfiguration;   /* currently selected configuration. Administered by driver, but not used */volatile schar usbRxLen;        /* = 0; number of bytes in usbRxBuf; 0 means free, -1 for flow control */uchar       usbCurrentTok;      /* last token received, if more than 1 rx endpoint: MSb=endpoint */uchar       usbRxToken;         /* token for data we received; if more than 1 rx endpoint: MSb=endpoint */uchar       usbMsgLen = 0xff;   /* remaining number of bytes, no msg to send if -1 (see usbMsgPtr) */volatile uchar usbTxLen = USBPID_NAK;   /* number of bytes to transmit with next IN token or handshake token */uchar       usbTxBuf[USB_BUFSIZE];/* data to transmit with next IN, free if usbTxLen contains handshake token */#if USB_CFG_HAVE_INTRIN_ENDPOINTvolatile uchar usbTxLen1 = USBPID_NAK;  /* TX count for endpoint 1 */uchar       usbTxBuf1[USB_BUFSIZE];     /* TX data for endpoint 1 */#if USB_CFG_HAVE_INTRIN_ENDPOINT3volatile uchar usbTxLen3 = USBPID_NAK;  /* TX count for endpoint 1 */uchar       usbTxBuf3[USB_BUFSIZE];     /* TX data for endpoint 1 */#endif#endif/* USB status registers / not shared with asm code */uchar           *usbMsgPtr;     /* data to transmit next -- ROM or RAM address */static uchar    usbMsgFlags;    /* flag values see below */#define USB_FLG_TX_PACKET       (1<<0)/* Leave free 6 bits after TX_PACKET. This way we can increment usbMsgFlags to toggle TX_PACKET */#define USB_FLG_MSGPTR_IS_ROM   (1<<6)#define USB_FLG_USE_DEFAULT_RW  (1<<7)/*optimizing hints:- do not post/pre inc/dec integer values in operations- assign value of PRG_RDB() to register variables and don't use side effects in arg- use narrow scope for variables which should be in X/Y/Z register- assign char sized expressions to variables to force 8 bit arithmetics*//* ------------------------------------------------------------------------- */#if USB_CFG_DESCR_PROPS_STRINGS == 0#if USB_CFG_DESCR_PROPS_STRING_0 == 0#undef USB_CFG_DESCR_PROPS_STRING_0#define USB_CFG_DESCR_PROPS_STRING_0    sizeof(usbDescriptorString0)PROGMEM char usbDescriptorString0[] = { /* language descriptor */    4,          /* sizeof(usbDescriptorString0): length of descriptor in bytes */    3,          /* descriptor type */    0x09, 0x04, /* language index (0x0409 = US-English) */};#endif#if USB_CFG_DESCR_PROPS_STRING_VENDOR == 0 && USB_CFG_VENDOR_NAME_LEN#undef USB_CFG_DESCR_PROPS_STRING_VENDOR#define USB_CFG_DESCR_PROPS_STRING_VENDOR   sizeof(usbDescriptorStringVendor)PROGMEM int  usbDescriptorStringVendor[] = {    USB_STRING_DESCRIPTOR_HEADER(USB_CFG_VENDOR_NAME_LEN),    USB_CFG_VENDOR_NAME};#endif#if USB_CFG_DESCR_PROPS_STRING_PRODUCT == 0 && USB_CFG_DEVICE_NAME_LEN#undef USB_CFG_DESCR_PROPS_STRING_PRODUCT#define USB_CFG_DESCR_PROPS_STRING_PRODUCT   sizeof(usbDescriptorStringDevice)PROGMEM int  usbDescriptorStringDevice[] = {    USB_STRING_DESCRIPTOR_HEADER(USB_CFG_DEVICE_NAME_LEN),    USB_CFG_DEVICE_NAME};#endif#if USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER == 0 && USB_CFG_SERIAL_NUMBER_LEN#undef USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    sizeof(usbDescriptorStringSerialNumber)PROGMEM int usbDescriptorStringSerialNumber[] = {    USB_STRING_DESCRIPTOR_HEADER(USB_CFG_SERIAL_NUMBER_LEN),    USB_CFG_SERIAL_NUMBER};#endif#endif  /* USB_CFG_DESCR_PROPS_STRINGS == 0 */#if USB_CFG_DESCR_PROPS_DEVICE == 0#undef USB_CFG_DESCR_PROPS_DEVICE#define USB_CFG_DESCR_PROPS_DEVICE  sizeof(usbDescriptorDevice)PROGMEM char usbDescriptorDevice[] = {    /* USB device descriptor */    18,         /* sizeof(usbDescriptorDevice): length of descriptor in bytes */    USBDESCR_DEVICE,        /* descriptor type */    0x10, 0x01,             /* USB version supported */    USB_CFG_DEVICE_CLASS,    USB_CFG_DEVICE_SUBCLASS,    0,                      /* protocol */    8,                      /* max packet size */    USB_CFG_VENDOR_ID,      /* 2 bytes */    USB_CFG_DEVICE_ID,      /* 2 bytes */    USB_CFG_DEVICE_VERSION, /* 2 bytes */    USB_CFG_DESCR_PROPS_STRING_VENDOR != 0 ? 1 : 0,         /* manufacturer string index */    USB_CFG_DESCR_PROPS_STRING_PRODUCT != 0 ? 2 : 0,        /* product string index */    USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER != 0 ? 3 : 0,  /* serial number string index */    1,          /* number of configurations */};#endif#if USB_CFG_DESCR_PROPS_HID_REPORT != 0 && USB_CFG_DESCR_PROPS_HID == 0#undef USB_CFG_DESCR_PROPS_HID#define USB_CFG_DESCR_PROPS_HID     9   /* length of HID descriptor in config descriptor below */#endif#if USB_CFG_DESCR_PROPS_CONFIGURATION == 0#undef USB_CFG_DESCR_PROPS_CONFIGURATION#define USB_CFG_DESCR_PROPS_CONFIGURATION   sizeof(usbDescriptorConfiguration)PROGMEM char usbDescriptorConfiguration[] = {    /* USB configuration descriptor */    9,          /* sizeof(usbDescriptorConfiguration): length of descriptor in bytes */    USBDESCR_CONFIG,    /* descriptor type */    18 + 7 * USB_CFG_HAVE_INTRIN_ENDPOINT + (USB_CFG_DESCR_PROPS_HID & 0xff), 0,                /* total length of data returned (including inlined descriptors) */    1,          /* number of interfaces in this configuration */    1,          /* index of this configuration */    0,          /* configuration name string index */#if USB_CFG_IS_SELF_POWERED    USBATTR_SELFPOWER,  /* attributes */#else    USBATTR_BUSPOWER,   /* attributes */#endif    USB_CFG_MAX_BUS_POWER/2,            /* max USB current in 2mA units *//* interface descriptor follows inline: */    9,          /* sizeof(usbDescrInterface): length of descriptor in bytes */    USBDESCR_INTERFACE, /* descriptor type */    0,          /* index of this interface */    0,          /* alternate setting for this interface */    USB_CFG_HAVE_INTRIN_ENDPOINT,   /* endpoints excl 0: number of endpoint descriptors to follow */    USB_CFG_INTERFACE_CLASS,    USB_CFG_INTERFACE_SUBCLASS,    USB_CFG_INTERFACE_PROTOCOL,    0,          /* string index for interface */#if (USB_CFG_DESCR_PROPS_HID & 0xff)    /* HID descriptor */    9,          /* sizeof(usbDescrHID): length of descriptor in bytes */    USBDESCR_HID,   /* descriptor type: HID */    0x01, 0x01, /* BCD representation of HID version */    0x00,       /* target country code */    0x01,       /* number of HID Report (or other HID class) Descriptor infos to follow */    0x22,       /* descriptor type: report */    USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH, 0,  /* total length of report descriptor */#endif#if USB_CFG_HAVE_INTRIN_ENDPOINT    /* endpoint descriptor for endpoint 1 */    7,          /* sizeof(usbDescrEndpoint) */    USBDESCR_ENDPOINT,  /* descriptor type = endpoint */    0x81,       /* IN endpoint number 1 */    0x03,       /* attrib: Interrupt endpoint */    8, 0,       /* maximum packet size */    USB_CFG_INTR_POLL_INTERVAL, /* in ms */#endif};#endif/* We don't use prog_int or prog_int16_t for compatibility with various libc * versions. Here's an other compatibility hack: */#ifndef PRG_RDB#define PRG_RDB(addr)   pgm_read_byte(addr)#endiftypedef union{    unsigned    word;    uchar       *ptr;    uchar       bytes[2];}converter_t;/* We use this union to do type conversions. This is better optimized than * type casts in gcc 3.4.3 and much better than using bit shifts to build * ints from chars. Byte ordering is not a problem on an 8 bit platform. *//* ------------------------------------------------------------------------- */#if USB_CFG_HAVE_INTRIN_ENDPOINTUSB_PUBLIC void usbSetInterrupt(uchar *data, uchar len){uchar       *p, i;#if USB_CFG_IMPLEMENT_HALT    if(usbTxLen1 == USBPID_STALL)        return;#endif#if 0   /* No runtime checks! Caller is responsible for valid data! */    if(len > 8) /* interrupt transfers are limited to 8 bytes */        len = 8;#endif    if(usbTxLen1 & 0x10){   /* packet buffer was empty */        usbTxBuf1[0] ^= USBPID_DATA0 ^ USBPID_DATA1;    /* toggle token */    }else{        usbTxLen1 = USBPID_NAK; /* avoid sending outdated (overwritten) interrupt data */    }    p = usbTxBuf1 + 1;    for(i=len;i--;)        *p++ = *data++;    usbCrc16Append(&usbTxBuf1[1], len);    usbTxLen1 = len + 4;    /* len must be given including sync byte */    DBG2(0x21, usbTxBuf1, len + 3);}#endif#if USB_CFG_HAVE_INTRIN_ENDPOINT3USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len){uchar       *p, i;    if(usbTxLen3 & 0x10){   /* packet buffer was empty */        usbTxBuf3[0] ^= USBPID_DATA0 ^ USBPID_DATA1;    /* toggle token */    }else{        usbTxLen3 = USBPID_NAK; /* avoid sending outdated (overwritten) interrupt data */    }    p = usbTxBuf3 + 1;    for(i=len;i--;)        *p++ = *data++;    usbCrc16Append(&usbTxBuf3[1], len);    usbTxLen3 = len + 4;    /* len must be given including sync byte */    DBG2(0x23, usbTxBuf3, len + 3);}#endifstatic uchar usbRead(uchar *data, uchar len){#if USB_CFG_IMPLEMENT_FN_READ    if(usbMsgFlags & USB_FLG_USE_DEFAULT_RW){#endif        uchar i = len, *r = usbMsgPtr;        if(usbMsgFlags & USB_FLG_MSGPTR_IS_ROM){    /* ROM data */            while(i--){                uchar c = PRG_RDB(r);    /* assign to char size variable to enforce byte ops */                *data++ = c;                r++;            }        }else{                  /* RAM data */            while(i--)                *data++ = *r++;        }        usbMsgPtr = r;        return len;#if USB_CFG_IMPLEMENT_FN_READ    }else{        if(len != 0)    /* don't bother app with 0 sized reads */            return usbFunctionRead(data, len);        return 0;