?? util.lst
字號:
{
TI_1=0;
SBUF1=0x34;
#if 0
while(TI_1_1==0) ;
TI_1=0;
SBUF1=0x35;
while(TI_1_1==0) ;
TI_1=0;
SBUF1=0x36;
while(TI_1_1==0) ;
TI_1=0;
#endif
}
}
#endif
196
197
198 //P1.4
199 void ISR_Int2(void) interrupt 8 //using 1
200 {
201 1
202 1 //if(SysTask==0)SysTask++;
203 1
204 1
205 1 }
206
207
208 void ISR_Int3(void) interrupt 9 //using 1
209 {
210 1
211 1 ;
212 1
213 1 }
214
215
216 void ISR_Int4(void) interrupt 10 //using 1
217 {
218 1
219 1 ;
220 1
221 1 }
222
223 void ISR_Int5(void) interrupt 11 //using 1
C51 COMPILER V7.50 UTIL 05/19/2008 18:30:54 PAGE 5
224 {
225 1
226 1 ;
227 1
228 1 }
229
230
231 void ISR_WatchDog(void) interrupt 12 //using 1
232 {
233 1
234 1 ;
235 1
236 1 }
237
238
239 #ifdef DEBUG_GPS
240 #define UART1_9600_11M
241 #else
#define UART1_4800_11M
#endif
244 /**************************************************************************
245 * Init system
246 **************************************************************************/
247 void CPU_init(void)
248 {
249 1
250 1 EA = 0;
*** ERROR C202 IN LINE 250 OF UTIL.C: 'EA': undefined identifier
251 1 EIE = 0;
*** ERROR C202 IN LINE 251 OF UTIL.C: 'EIE': undefined identifier
252 1
253 1 P1=0xff;
*** ERROR C202 IN LINE 253 OF UTIL.C: 'P1': undefined identifier
254 1 P3=0xff;
*** ERROR C202 IN LINE 254 OF UTIL.C: 'P3': undefined identifier
255 1 P0=0xff;
*** ERROR C202 IN LINE 255 OF UTIL.C: 'P0': undefined identifier
256 1
257 1 //system init ，其中串口0用定時器2，串口1用定時器1
258 1 //串口1的設置
259 1 IE = 0x90; //允許總中斷和串口0的中斷
*** ERROR C202 IN LINE 259 OF UTIL.C: 'IE': undefined identifier
260 1 TMOD=0x20; //定時器1工作在模式2
*** ERROR C202 IN LINE 260 OF UTIL.C: 'TMOD': undefined identifier
261 1 //CKCON=0x30; //Timerl和Timer2時鐘為1／12CLOCK
262 1 //CKCON |= 0x10; //Timer1 =1/4 clock
263 1 //CKCON |= 0x20; //Timer2 =1/4 clock
264 1
265 1 #if 0
TL1=?; //baud rate=1200 /11.0592
TH1=?;
#endif
269 1
270 1 #if 0
TL1=244; //baud rate=2400 /11.0592
TH1=244;
#endif
274 1
275 1 #ifdef UART1_4800_11M //def BAUD_4800_11M
TL1=250; //0xfa 0xfa is baud rate=4800 /11.0592
TH1=250;
C51 COMPILER V7.50 UTIL 05/19/2008 18:30:54 PAGE 6
#endif
280 1
281 1 #ifdef UART1_9600_11M
282 1 TL1=253; //0XFDFD baud rate=9600 /11.0592
*** ERROR C202 IN LINE 282 OF UTIL.C: 'TL1': undefined identifier
283 1 TH1=253;
*** ERROR C202 IN LINE 283 OF UTIL.C: 'TH1': undefined identifier
284 1 #endif
285 1
286 1
287 1
288 1 SCON1=0x58; //工作在模式1,允許接收
*** ERROR C202 IN LINE 288 OF UTIL.C: 'SCON1': undefined identifier
289 1 //SCON1=0x50; /* mode 1: 8-bit UART, enable receiver */
290 1 //SMOD_1 = 1; //UART1 baud*2
291 1 ES1=1; //串口1中斷允許
*** ERROR C202 IN LINE 291 OF UTIL.C: 'ES1': undefined identifier
292 1
293 1 SCON=0x58; //工作在模式1，接收允許;
*** ERROR C202 IN LINE 293 OF UTIL.C: 'SCON': undefined identifier
294 1 //SCON=0x50; /* mode 1: 8-bit UART, enable receiver */
295 1
296 1 PCON = 0x00; // SM0=0 SM1=1 在10位異步收發模式 SMOD=0 溢出速率/32
*** ERROR C202 IN LINE 296 OF UTIL.C: 'PCON': undefined identifier
297 1 //PCON = 0x80; //UART0 baud*2
298 1
299 1
300 1 //定時器2：波特率＝振蕩器頻率/(32*(65536-(RCAP2H,RCAP2L)))
301 1 //9600=11059200/(32X(65536-RCAP2HL))
302 1
303 1 T2CON=0x30; //用定時器2做串口0的波特率發生器
*** ERROR C202 IN LINE 303 OF UTIL.C: 'T2CON': undefined identifier
304 1
305 1 #if 0
RCAP2H=0xfe; // 11.0592M晶振下, baud rate=1200
RCAP2L=0xe0;
#endif
309 1 #if 0
RCAP2H=0xff; // 11.0592M晶振下, baud rate=2400
RCAP2L=0x70;
#endif
313 1
314 1 #ifdef UART0_4800_11M
RCAP2H=0xff; // 11.0592M晶振下, baud rate=4800
RCAP2L=0xb8;
#endif
318 1
319 1
320 1 #ifdef UART0_9600_11M
RCAP2H=0xff; // 11.0592M晶振下, baud rate=9600
RCAP2L=0xdc;
#endif
324 1
325 1
326 1 #ifdef UART0_19200_11M
327 1 RCAP2H=0xff; // 11.0592M晶振下, baud rate=19200 ?
*** ERROR C202 IN LINE 327 OF UTIL.C: 'RCAP2H': undefined identifier
328 1 RCAP2L=0xee;
*** ERROR C202 IN LINE 328 OF UTIL.C: 'RCAP2L': undefined identifier
329 1 #endif
330 1
331 1
C51 COMPILER V7.50 UTIL 05/19/2008 18:30:54 PAGE 7
332 1 #ifdef UART0_38400_11M
RCAP2H=0xff; // 11.0592M晶振下, baud rate=38400 ?
RCAP2L=0xf7;
#endif
336 1
337 1
338 1
339 1
340 1 TMOD |=0x01; //th1 auto load 2X8,th0 1X16
*** ERROR C202 IN LINE 340 OF UTIL.C: 'TMOD': undefined identifier
341 1 ET0 = 1;
*** ERROR C202 IN LINE 341 OF UTIL.C: 'ET0': undefined identifier
342 1 TH0 = 0xf7;
*** ERROR C202 IN LINE 342 OF UTIL.C: 'TH0': undefined identifier
343 1 TL0 = 0x60;
*** ERROR C202 IN LINE 343 OF UTIL.C: 'TL0': undefined identifier
344 1 TR0 = 1;
*** ERROR C202 IN LINE 344 OF UTIL.C: 'TR0': undefined identifier
345 1
346 1 TR2 = 1;
*** ERROR C202 IN LINE 346 OF UTIL.C: 'TR2': undefined identifier
347 1 TR1 = 1;
*** ERROR C202 IN LINE 347 OF UTIL.C: 'TR1': undefined identifier
348 1
349 1 }/*end CPU_system_init*/
350
351
352
C51 COMPILATION COMPLETE. 1 WARNING(S), 37 ERROR(S)
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -