/* * linux/arch/arm/mach-at91rm9200/board-ek.c * *  Copyright (C) 2005 SAN People * *  Epson S1D framebuffer glue code is: *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA */#include <linux/config.h>#include <linux/types.h>#include <linux/init.h>#include <linux/mm.h>#include <linux/module.h>#include <linux/platform_device.h>#include <asm/hardware.h>#include <asm/setup.h>#include <asm/mach-types.h>#include <asm/irq.h>#include <asm/mach/arch.h>#include <asm/mach/map.h>#include <asm/mach/irq.h>#include <asm/arch/hardware.h>#include <asm/mach/serial_at91rm9200.h>#include <asm/arch/board.h>#include "generic.h"static void __init ek_init_irq(void){	/* Initialize AIC controller */	at91rm9200_init_irq(NULL);	/* Set up the GPIO interrupts */	at91_gpio_irq_setup(BGA_GPIO_BANKS);}/* * Serial port configuration. *    0 .. 3 = USART0 .. USART3 *    4      = DBGU */#define EK_UART_MAP		{ 4, 1, -1, -1, -1 }	/* ttyS0, ..., ttyS4 */#define EK_SERIAL_CONSOLE	0			/* ttyS0 */static void __init ek_map_io(void){	int serial[AT91_NR_UART] = EK_UART_MAP;	int i;	at91rm9200_map_io();	/* Initialize clocks: 18.432 MHz crystal */	at91_clock_init(18432000);	/* Setup the LEDs */	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);#ifdef CONFIG_SERIAL_AT91	at91_console_port = EK_SERIAL_CONSOLE;	memcpy(at91_serial_map, serial, sizeof(serial));	/* Register UARTs */	for (i = 0; i < AT91_NR_UART; i++) {		if (serial[i] >= 0)			at91_register_uart(i, serial[i]);	}#endif}static struct at91_eth_data __initdata ek_eth_data = {	.phy_irq_pin	= AT91_PIN_PC4,	.is_rmii	= 1,};static struct at91_usbh_data __initdata ek_usbh_data = {	.ports		= 2,};static struct at91_udc_data __initdata ek_udc_data = {	.vbus_pin	= AT91_PIN_PD4,	.pullup_pin	= AT91_PIN_PD5,};static struct at91_mmc_data __initdata ek_mmc_data = {	.det_pin	= AT91_PIN_PB27,	.is_b		= 0,	.wire4		= 1,	.wp_pin		= AT91_PIN_PA17,};static void __init ek_board_init(void){	/* Ethernet */	at91_add_device_eth(&ek_eth_data);	/* USB Host */	at91_add_device_usbh(&ek_usbh_data);	/* USB Device */	at91_add_device_udc(&ek_udc_data);#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD	/* DataFlash card */	at91_set_gpio_output(AT91_PIN_PB22, 0);#else	/* MMC */	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */	at91_add_device_mmc(&ek_mmc_data);#endif	/* VGA *///	ek_add_device_video();}MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")	/* Maintainer: SAN People/Atmel */	.phys_io	= AT91_BASE_SYS,	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,	.boot_params	= AT91_SDRAM_BASE + 0x100,	.timer		= &at91rm9200_timer,	.map_io		= ek_map_io,	.init_irq	= ek_init_irq,	.init_machine	= ek_board_init,MACHINE_END