?? at91sam7x128_inc.h
字號:
#define AT91C_SSC_FSOS_HIGH (0x4 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Driver High during data transfer
#define AT91C_SSC_FSOS_TOGGLE (0x5 << 20) // (SSC) Selected Receive/Transmit Frame Sync Signal: Toggling at each start of data transfer
#define AT91C_SSC_FSEDGE (0x1 << 24) // (SSC) Frame Sync Edge Detection
// -------- SSC_TCMR : (SSC Offset: 0x18) SSC Transmit Clock Mode Register --------
// -------- SSC_TFMR : (SSC Offset: 0x1c) SSC Transmit Frame Mode Register --------
#define AT91C_SSC_DATDEF (0x1 << 5) // (SSC) Data Default Value
#define AT91C_SSC_FSDEN (0x1 << 23) // (SSC) Frame Sync Data Enable
// -------- SSC_SR : (SSC Offset: 0x40) SSC Status Register --------
#define AT91C_SSC_TXRDY (0x1 << 0) // (SSC) Transmit Ready
#define AT91C_SSC_TXEMPTY (0x1 << 1) // (SSC) Transmit Empty
#define AT91C_SSC_ENDTX (0x1 << 2) // (SSC) End Of Transmission
#define AT91C_SSC_TXBUFE (0x1 << 3) // (SSC) Transmit Buffer Empty
#define AT91C_SSC_RXRDY (0x1 << 4) // (SSC) Receive Ready
#define AT91C_SSC_OVRUN (0x1 << 5) // (SSC) Receive Overrun
#define AT91C_SSC_ENDRX (0x1 << 6) // (SSC) End of Reception
#define AT91C_SSC_RXBUFF (0x1 << 7) // (SSC) Receive Buffer Full
#define AT91C_SSC_TXSYN (0x1 << 10) // (SSC) Transmit Sync
#define AT91C_SSC_RXSYN (0x1 << 11) // (SSC) Receive Sync
#define AT91C_SSC_TXENA (0x1 << 16) // (SSC) Transmit Enable
#define AT91C_SSC_RXENA (0x1 << 17) // (SSC) Receive Enable
// -------- SSC_IER : (SSC Offset: 0x44) SSC Interrupt Enable Register --------
// -------- SSC_IDR : (SSC Offset: 0x48) SSC Interrupt Disable Register --------
// -------- SSC_IMR : (SSC Offset: 0x4c) SSC Interrupt Mask Register --------
// *****************************************************************************
// SOFTWARE API DEFINITION FOR Two-wire Interface
// *****************************************************************************
// *** Register offset in AT91S_TWI structure ***
#define TWI_CR ( 0) // Control Register
#define TWI_MMR ( 4) // Master Mode Register
#define TWI_IADR (12) // Internal Address Register
#define TWI_CWGR (16) // Clock Waveform Generator Register
#define TWI_SR (32) // Status Register
#define TWI_IER (36) // Interrupt Enable Register
#define TWI_IDR (40) // Interrupt Disable Register
#define TWI_IMR (44) // Interrupt Mask Register
#define TWI_RHR (48) // Receive Holding Register
#define TWI_THR (52) // Transmit Holding Register
// -------- TWI_CR : (TWI Offset: 0x0) TWI Control Register --------
#define AT91C_TWI_START (0x1 << 0) // (TWI) Send a START Condition
#define AT91C_TWI_STOP (0x1 << 1) // (TWI) Send a STOP Condition
#define AT91C_TWI_MSEN (0x1 << 2) // (TWI) TWI Master Transfer Enabled
#define AT91C_TWI_MSDIS (0x1 << 3) // (TWI) TWI Master Transfer Disabled
#define AT91C_TWI_SWRST (0x1 << 7) // (TWI) Software Reset
// -------- TWI_MMR : (TWI Offset: 0x4) TWI Master Mode Register --------
#define AT91C_TWI_IADRSZ (0x3 << 8) // (TWI) Internal Device Address Size
#define AT91C_TWI_IADRSZ_NO (0x0 << 8) // (TWI) No internal device address
#define AT91C_TWI_IADRSZ_1_BYTE (0x1 << 8) // (TWI) One-byte internal device address
#define AT91C_TWI_IADRSZ_2_BYTE (0x2 << 8) // (TWI) Two-byte internal device address
#define AT91C_TWI_IADRSZ_3_BYTE (0x3 << 8) // (TWI) Three-byte internal device address
#define AT91C_TWI_MREAD (0x1 << 12) // (TWI) Master Read Direction
#define AT91C_TWI_DADR (0x7F << 16) // (TWI) Device Address
// -------- TWI_CWGR : (TWI Offset: 0x10) TWI Clock Waveform Generator Register --------
#define AT91C_TWI_CLDIV (0xFF << 0) // (TWI) Clock Low Divider
#define AT91C_TWI_CHDIV (0xFF << 8) // (TWI) Clock High Divider
#define AT91C_TWI_CKDIV (0x7 << 16) // (TWI) Clock Divider
// -------- TWI_SR : (TWI Offset: 0x20) TWI Status Register --------
#define AT91C_TWI_TXCOMP (0x1 << 0) // (TWI) Transmission Completed
#define AT91C_TWI_RXRDY (0x1 << 1) // (TWI) Receive holding register ReaDY
#define AT91C_TWI_TXRDY (0x1 << 2) // (TWI) Transmit holding register ReaDY
#define AT91C_TWI_OVRE (0x1 << 6) // (TWI) Overrun Error
#define AT91C_TWI_UNRE (0x1 << 7) // (TWI) Underrun Error
#define AT91C_TWI_NACK (0x1 << 8) // (TWI) Not Acknowledged
// -------- TWI_IER : (TWI Offset: 0x24) TWI Interrupt Enable Register --------
// -------- TWI_IDR : (TWI Offset: 0x28) TWI Interrupt Disable Register --------
// -------- TWI_IMR : (TWI Offset: 0x2c) TWI Interrupt Mask Register --------
// *****************************************************************************
// SOFTWARE API DEFINITION FOR PWMC Channel Interface
// *****************************************************************************
// *** Register offset in AT91S_PWMC_CH structure ***
#define PWMC_CMR ( 0) // Channel Mode Register
#define PWMC_CDTYR ( 4) // Channel Duty Cycle Register
#define PWMC_CPRDR ( 8) // Channel Period Register
#define PWMC_CCNTR (12) // Channel Counter Register
#define PWMC_CUPDR (16) // Channel Update Register
#define PWMC_Reserved (20) // Reserved
// -------- PWMC_CMR : (PWMC_CH Offset: 0x0) PWMC Channel Mode Register --------
#define AT91C_PWMC_CPRE (0xF << 0) // (PWMC_CH) Channel Pre-scaler : PWMC_CLKx
#define AT91C_PWMC_CPRE_MCK (0x0) // (PWMC_CH)
#define AT91C_PWMC_CPRE_MCKA (0xB) // (PWMC_CH)
#define AT91C_PWMC_CPRE_MCKB (0xC) // (PWMC_CH)
#define AT91C_PWMC_CALG (0x1 << 8) // (PWMC_CH) Channel Alignment
#define AT91C_PWMC_CPOL (0x1 << 9) // (PWMC_CH) Channel Polarity
#define AT91C_PWMC_CPD (0x1 << 10) // (PWMC_CH) Channel Update Period
// -------- PWMC_CDTYR : (PWMC_CH Offset: 0x4) PWMC Channel Duty Cycle Register --------
#define AT91C_PWMC_CDTY (0x0 << 0) // (PWMC_CH) Channel Duty Cycle
// -------- PWMC_CPRDR : (PWMC_CH Offset: 0x8) PWMC Channel Period Register --------
#define AT91C_PWMC_CPRD (0x0 << 0) // (PWMC_CH) Channel Period
// -------- PWMC_CCNTR : (PWMC_CH Offset: 0xc) PWMC Channel Counter Register --------
#define AT91C_PWMC_CCNT (0x0 << 0) // (PWMC_CH) Channel Counter
// -------- PWMC_CUPDR : (PWMC_CH Offset: 0x10) PWMC Channel Update Register --------
#define AT91C_PWMC_CUPD (0x0 << 0) // (PWMC_CH) Channel Update
// *****************************************************************************
// SOFTWARE API DEFINITION FOR Pulse Width Modulation Controller Interface
// *****************************************************************************
// *** Register offset in AT91S_PWMC structure ***
#define PWMC_MR ( 0) // PWMC Mode Register
#define PWMC_ENA ( 4) // PWMC Enable Register
#define PWMC_DIS ( 8) // PWMC Disable Register
#define PWMC_SR (12) // PWMC Status Register
#define PWMC_IER (16) // PWMC Interrupt Enable Register
#define PWMC_IDR (20) // PWMC Interrupt Disable Register
#define PWMC_IMR (24) // PWMC Interrupt Mask Register
#define PWMC_ISR (28) // PWMC Interrupt Status Register
#define PWMC_VR (252) // PWMC Version Register
#define PWMC_CH (512) // PWMC Channel
// -------- PWMC_MR : (PWMC Offset: 0x0) PWMC Mode Register --------
#define AT91C_PWMC_DIVA (0xFF << 0) // (PWMC) CLKA divide factor.
#define AT91C_PWMC_PREA (0xF << 8) // (PWMC) Divider Input Clock Prescaler A
#define AT91C_PWMC_PREA_MCK (0x0 << 8) // (PWMC)
#define AT91C_PWMC_DIVB (0xFF << 16) // (PWMC) CLKB divide factor.
#define AT91C_PWMC_PREB (0xF << 24) // (PWMC) Divider Input Clock Prescaler B
#define AT91C_PWMC_PREB_MCK (0x0 << 24) // (PWMC)
// -------- PWMC_ENA : (PWMC Offset: 0x4) PWMC Enable Register --------
#define AT91C_PWMC_CHID0 (0x1 << 0) // (PWMC) Channel ID 0
#define AT91C_PWMC_CHID1 (0x1 << 1) // (PWMC) Channel ID 1
#define AT91C_PWMC_CHID2 (0x1 << 2) // (PWMC) Channel ID 2
#define AT91C_PWMC_CHID3 (0x1 << 3) // (PWMC) Channel ID 3
// -------- PWMC_DIS : (PWMC Offset: 0x8) PWMC Disable Register --------
// -------- PWMC_SR : (PWMC Offset: 0xc) PWMC Status Register --------
// -------- PWMC_IER : (PWMC Offset: 0x10) PWMC Interrupt Enable Register --------
// -------- PWMC_IDR : (PWMC Offset: 0x14) PWMC Interrupt Disable Register --------
// -------- PWMC_IMR : (PWMC Offset: 0x18) PWMC Interrupt Mask Register --------
// -------- PWMC_ISR : (PWMC Offset: 0x1c) PWMC Interrupt Status Register --------
// *****************************************************************************
// SOFTWARE API DEFINITION FOR USB Device Interface
// *****************************************************************************
// *** Register offset in AT91S_UDP structure ***
#define UDP_NUM ( 0) // Frame Number Register
#define UDP_GLBSTATE ( 4) // Global State Register
#define UDP_FADDR ( 8) // Function Address Register
#define UDP_IER (16) // Interrupt Enable Register
#define UDP_IDR (20) // Interrupt Disable Register
#define UDP_IMR (24) // Interrupt Mask Register
#define UDP_ISR (28) // Interrupt Status Register
#define UDP_ICR (32) // Interrupt Clear Register
#define UDP_RSTEP (40) // Reset Endpoint Register
#define UDP_CSR (48) // Endpoint Control and Status Register
#define UDP_FDR (80) // Endpoint FIFO Data Register
#define UDP_TXVC (116) // Transceiver Control Register
// -------- UDP_FRM_NUM : (UDP Offset: 0x0) USB Frame Number Register --------
#define AT91C_UDP_FRM_NUM (0x7FF << 0) // (UDP) Frame Number as Defined in the Packet Field Formats
#define AT91C_UDP_FRM_ERR (0x1 << 16) // (UDP) Frame Error
#define AT91C_UDP_FRM_OK (0x1 << 17) // (UDP) Frame OK
// -------- UDP_GLB_STATE : (UDP Offset: 0x4) USB Global State Register --------
#define AT91C_UDP_FADDEN (0x1 << 0) // (UDP) Function Address Enable
#define AT91C_UDP_CONFG (0x1 << 1) // (UDP) Configured
#define AT91C_UDP_ESR (0x1 << 2) // (UDP) Enable Send Resume
#define AT91C_UDP_RSMINPR (0x1 << 3) // (UDP) A Resume Has Been Sent to the Host
#define AT91C_UDP_RMWUPE (0x1 << 4) // (UDP) Remote Wake Up Enable
// -------- UDP_FADDR : (UDP Offset: 0x8) USB Function Address Register --------
#define AT91C_UDP_FADD (0xFF << 0) // (UDP) Function Address Value
#define AT91C_UDP_FEN (0x1 << 8) // (UDP) Function Enable
// -------- UDP_IER : (UDP Offset: 0x10) USB Interrupt Enable Register --------
#define AT91C_UDP_EPINT0 (0x1 << 0) // (UDP) Endpoint 0 Interrupt
#define AT91C_UDP_EPINT1 (0x1 << 1) // (UDP) Endpoint 0 Interrupt
#define AT91C_UDP_EPINT2 (0x1 << 2) // (UDP) Endpoint 2 Interrupt
#define AT91C_UDP_EPINT3 (0x1 << 3) // (UDP) Endpoint 3 Interrupt
#define AT91C_UDP_EPINT4 (0x1 << 4) // (UDP) Endpoint 4 Interrupt
#define AT91C_UDP_EPINT5 (0x1 << 5) // (UDP) Endpoint 5 Interrupt
#define AT91C_UDP_RXSUSP (0x1 << 8) // (UDP) USB Suspend Interrupt
#define AT91C_UDP_RXRSM (0x1 << 9) // (UDP) USB Resume Interrupt
#define AT91C_UDP_EXTRSM (0x1 << 10) // (UDP) USB External Resume Interrupt
#define AT91C_UDP_SOFINT (0x1 << 11) // (UDP) USB Start Of frame Interrupt
#define AT91C_UDP_WAKEUP (0x1 << 13) // (UDP) USB Resume Interrupt
// -------- UDP_IDR : (UDP Offset: 0x14) USB Interrupt Disable Register --------
// -------- UDP_IMR : (UDP Offset: 0x18) USB Interrupt Mask Register --------
// -------- UDP_ISR : (UDP Offset: 0x1c) USB Interrupt Status Register --------
#define AT91C_UDP_ENDBUSRES (0x1 << 12) // (UDP) USB End Of Bus Reset Interrupt
// -------- UDP_ICR : (UDP Offset: 0x20) USB Interrupt Clear Register --------
// -------- UDP_RST_EP : (UDP Offset: 0x28) USB Reset Endpoint Register --------
#define AT91C_UDP?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -