?? 44blib.c
字號:
#include "..\colorlcd-inc\44b.h"
#include "..\colorlcd-inc\44blib.h"
#include "..\colorlcd-inc\def.h"
#include "..\colorlcd-inc\option.h"
#include <stdarg.h>
#include <string.h>
#include <stdio.h>
#include <ctype.h>
#define STACKSIZE 0xa00 //SVC satck size(do not use user stack)//
#define HEAPEND (_ISR_STARTADDRESS-STACKSIZE-0x500) // = 0xc7ff000//
//SVC Stack Area:0xc(e)7ff000-0xc(e)7ffaff//
extern char Image_RW_Limit[];
volatile unsigned char *downPt;
unsigned int fileSize;
void *mallocPt=Image_RW_Limit;
void (*restart)(void)=(void (*)(void))0x0;
void (*run)(void)=(void (*)(void))DOWNLOAD_ADDRESS;
//--------------------------------SYSTEM---------------------------------//
static int delayLoopCount=400;
void Delay(int time)
// time=0: adjust the Delay function by WatchDog timer.//
// time>0: the number of loop time//
// 100us resolution.//
{
int i,adjust=0;
if(time==0)
{
time=200;
adjust=1;
delayLoopCount=400;
rWTCON=((MCLK/1000000-1)<<8)|(2<<3); // 1M/64,Watch-dog,nRESET,interrupt disable//
rWTDAT=0xffff;
rWTCNT=0xffff;
rWTCON=((MCLK/1000000-1)<<8)|(2<<3)|(1<<5); // 1M/64,Watch-dog enable,nRESET,interrupt disable //
}
for(;time>0;time--)
for(i=0;i<delayLoopCount;i++);
if(adjust==1)
{
rWTCON=((MCLK/1000000-1)<<8)|(2<<3);
i=0xffff-rWTCNT; // 1count/16us?????????//
delayLoopCount=8000000/(i*64); //400*100/(i*64/200) //
}
}
//------------------------PORTS------------------------------//
void Port_Init(void)
{
//CAUTION:Follow the configuration order for setting the ports.
// 1) setting value
// 2) setting control register
// 3) configure pull-up resistor.
//16bit data bus configuration
// PORT A GROUP
/* BIT 9 8 7 6 5 4 3 2 1 0 */
/* A24 A23 A22 A21 A20 A19 A18 A17 A16 A0 */
/* 1 1 1 1 1 1 1 1 1 1 */
rPCONA = 0x1ff; //the second funcation(npq)
// PORT B GROUP
/* BIT 10 9 8 7 6 5 4 3 2 1 0 */
/* /CS5 /CS4 /CS3 /CS2 /CS1 nWBE3 nWBE2 /SRAS /SCAS SCLK SCKE */
/* EXT NIC USB IDE SMC NC NC Sdram Sdram Sdram Sdram */
/* 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1 */
rPDATB = 0x7ff;
rPCONB = 0x7ff; //the second funcation(npq) expert GPB6 and GPB7
//PORT C GROUP
//BUSWIDTH=16 */
/* PC15 14 13 12 11 10 9 8 */
/* I I I I I I I I */
/* NC NC Uart1 Uart1 NC NC NC NC */
/* 00 00 11/00 11/00 00 00 00 00 */
/* PC7 6 5 4 3 2 1 0 */
/* I I I I I I O O */
/* VD4 VD5 VD6 VD7 SMCALE SMCCLE SMCCE SMCRB*/
/* 11 11 11 11 00 00 01 01 */
rPDATC = 0xffff; //All IO is high
rPCONC = 0x5145ff51; //(npq)
rPUPC = 0x0000; //PULL UP RESISTOR should be enabled to I/O
//PORT D GROUP
/* PORT D GROUP(I/O OR LCD) */
/* BIT7 6 5 4 3 2 1 0 */
/* VF VM VLINE VCLK VD3 VD2 VD1 VD0 */
/* 00 00 00 00 00 00 00 00 */
rPDATD= 0xff;
rPCOND= 0xaaaa; //the second funcation
rPUPD = 0x0;
//These pins must be set only after CPU's internal LCD controller is enable
//PORT E GROUP
/* Bit 8 7 6 5 4 3 2 1 0 */
/* ENDAIN CLEARCOL DIN SSCLK DACSSTEP DACSCOL RXD0 TXD0 NC */
/* 00 01 01 01 01 01 10 10 01 */
//rPDATE = 0x1ff;
rPDATE = 0x0;
rPCONE = 0x05029; //(npq)
rPUPE = 0x06; //output need the Uppull!(npq)
//PORT F GROUP
/* Bit8 7 6 5 4 3 2 1 0 */
/* DISPOFF RXD1 TXD1 PortSel NC PosSel2 PosSel1 DOWN1 UP1 */
/* 001 010 010 001 00 01 01 00 00 */
/* DISPOFF input input PortSel NC PosSel2 PosSel1 DOWN1 UP1 */
/* 001 000 000 001 00 01 01 00 00 */
//rPDATF = 0x0;
rPCONF = 0x15515; // nWAIT/GPF2 is output(npq)
rPUPF = 0x0;
//PORT G GROUP
/* BIT7 6 5 4 3 2 1 0 */
/* PANELSel Snob1 Snob2 Cnob1 Cnob2 INT2 INT1 INT0 */
/* S3 S4 S5 S6 NIC EXT IDE USB */
/* 01 00 00 00 00 11 11 11 */
rPDATG = 0x40; //??????????(npq)
rPCONG = 0x0554; // (npq)
rPUPG = 0x0; //should be enabled(npq)
rSPUCR=0x7; //D15-D0 pull-up disable
/*定義非Cache區*/
rNCACHBE0=((Non_Cache_End>>12)<<16)|(Non_Cache_Start>>12);
/*所有的外部硬件中斷為低電平觸發*/
rEXTINT=0x22222222; // INT0-INT7為下沿觸發
// rEXTINT=0x44444444; // INT0-INT7為上沿觸發
// rEXTINT=0x0; // INT1為下沿觸發
// rEXTINT=0x10; // INT1為下沿觸發
// rPDATF = rPDATF&0x1bf; // DISPOFF=0, turn off LCD
rPDATF = rPDATF&0xff; // DISPOFF=0, turn off LCD
rPDATD = rPDATD|0x20; // DISPOFF=0, turn off LCD
//Misc
//USBN9603's A0 pin -> CPU's A1
//IDE's CS0 -> CPU's A2
//IDE's CS1 -> CPU's A1
//IDE's A2 -> CPU's A3
//IDE's A1 -> CPU's A5
//IDE's A0 -> CPU's A4
}
/************************* UART ****************************/
static int whichUart=0;
void Uart_Init(int ch,int baud)
{
int i,mclk;
// if(mclk==0)
mclk=MCLK;
mclk=40000000;
rUFCON0=0x0; //FIFO disable
rUFCON1=0x0;
rUMCON0=0x0;
rUMCON1=0x0;
//UART0
rULCON0=0x3; //Normal,No parity,1 stop,8 bit
rUCON0=0x245; //rx=edge,tx=level,disable timeout int.,enable rx error int.,normal,interrupt or polling
if(ch==0)
rUBRDIV0=( (int)(mclk/16./baud + 0.5) -1 );
//UART1
rULCON1=0x3;
rUCON1=0x245;
if(ch==1)
rUBRDIV1=( (int)(mclk/16./baud + 0.5) -1 );
for(i=0;i<100;i++);
}
void Uart_Select(int ch)
{
whichUart=ch;
}
void Uart_TxEmpty(int ch)
{
if(ch==0)
while(!(rUTRSTAT0 & 0x4)); //wait until tx shifter is empty.
else
while(!(rUTRSTAT1 & 0x4)); //wait until tx shifter is empty.
}
char Uart_Getch(void)
{
if(whichUart==0)
{
while(!(rUTRSTAT0 & 0x1)); //Receive data read
return RdURXH0();
}
else
{
while(!(rUTRSTAT1 & 0x1)); //Receive data ready
return rURXH1;
}
}
char Uart_GetKey(void)
{
if(whichUart==0)
{
if(rUTRSTAT0 & 0x1) //Receive data ready
return RdURXH0();
else
return 0;
}
else
{
if(rUTRSTAT1 & 0x1) //Receive data ready
return rURXH1;
else
return 0;
}
}
void Uart_GetString(char *string)
{
char *string2=string;
char c;
while((c=Uart_Getch())!='\r')
{
if(c=='\b')
{
if( (int)string2 < (int)string )
{
Uart_Printf("\b \b");
string--;
}
}
else
{
*string++=c;
Uart_SendByte(c);
}
}
*string='\0';
Uart_SendByte('\n');
}
int Uart_GetIntNum(void)
{
char str[30];
char *string=str;
int base=10;
int minus=0;
int lastIndex;
int result=0;
int i;
Uart_GetString(string);
if(string[0]=='-')
{
minus=1;
string++;
}
if(string[0]=='0' && (string[1]=='x' || string[1]=='X'))
{
base=16;
string+=2;
}
lastIndex=strlen(string)-1;
if( string[lastIndex]=='h' || string[lastIndex]=='H' )
{
base=16;
string[lastIndex]=0;
lastIndex--;
}
if(base==10)
{
result=atoi(string);
result=minus ? (-1*result):result;
}
else
{
for(i=0;i<=lastIndex;i++)
{
if(isalpha(string[i]))
{
if(isupper(string[i]))
result=(result<<4)+string[i]-'A'+10;
else
result=(result<<4)+string[i]-'a'+10;
}
else
{
result=(result<<4)+string[i]-'0';
}
}
result=minus ? (-1*result):result;
}
return result;
}
void Uart_SendByte(int data)
{
if(whichUart==0)
{
// if(data=='\n')
// {
while(!(rUTRSTAT0 & 0x2));
// Delay(5); //because the slow response of hyper_terminal
// WrUTXH0('\r');
// }
while(!(rUTRSTAT0 & 0x2)); //Wait until THR is empty.
// Delay(5);
WrUTXH0(data);
}
else
{
// if(data=='\n')
//{
// while(!(rUTRSTAT1 & 0x2));
// Delay(5); //because the slow response of hyper_terminal
// rUTXH1='\r';
//}
while(!(rUTRSTAT1 & 0x2)); //Wait until THR is empty.
// Delay(5);
rUTXH1=data;
}
}
void Uart_SendString(char *pt)
{
while(*pt)
Uart_SendByte(*pt++);
}
//if you don't use vsprintf(), the code size is reduced very much.
void Uart_Printf(char *fmt,...)
{
va_list ap;
char string[256];
va_start(ap,fmt);
vsprintf(string,fmt,ap);
Uart_SendString(string);
va_end(ap);
}
/******************** S3C44B0X EV. BOARD LED **********************/
void Led_Display(int LedStatus)
{
if((LedStatus&0x01)==0x01)
rPDATE=rPDATE&0x17f;
else
rPDATE=rPDATE|0x80;
if((LedStatus&0x02)==0x02)
rPDATE=rPDATE&0x1bf;
else
rPDATE=rPDATE|0x40;
if((LedStatus&0x04)==0x04)
rPDATE=rPDATE&0x1df;
else
rPDATE=rPDATE|0x20;
if((LedStatus&0x08)==0x08)
rPDATE=rPDATE&0x1ef;
else
rPDATE=rPDATE|0x10;
}
/************************* Timer ********************************/
void Timer_Start(int divider) //0:16us,1:32us 2:64us 3:128us
{
rWTCON=((MCLK/1000000-1)<<8)|(divider<<3);
rWTDAT=0xffff;
rWTCNT=0xffff;
// 1/16/(65+1),nRESET & interrupt disable
rWTCON=((MCLK/1000000-1)<<8)|(divider<<3)|(1<<5);
}
int Timer_Stop(void)
{
rWTCON=((MCLK/1000000-1)<<8);
return (0xffff-rWTCNT);
}
void Beep(int BeepStatus)
{
if (BeepStatus==0)
rPDATE=rPDATE|0x8;
else
rPDATE=rPDATE&0x1f7;
}
/************************* PLL ********************************/
void ChangePllValue(int mdiv,int pdiv,int sdiv)
{
rPLLCON=(mdiv<<12)|(pdiv<<4)|sdiv;
}
/************************* General Library **********************/
void * malloc(unsigned nbyte)
/*Very simple; Use malloc() & free() like Stack*/
//void *mallocPt=Image$$RW$$Limit;
{
void *returnPt=mallocPt;
mallocPt= (int *)mallocPt+nbyte/4+((nbyte%4)>0); //to align 4byte
if( (int)mallocPt > HEAPEND )
{
mallocPt=returnPt;
return NULL;
}
return returnPt;
}
void free(void *pt)
{
mallocPt=pt;
}
void Cache_Flush(void)
{
int i,saveSyscfg;
saveSyscfg=rSYSCFG;
rSYSCFG=SYSCFG_0KB;
for(i=0x10004000;i<0x10004800;i+=16)
{
*((int *)i)=0x0;
}
rSYSCFG=saveSyscfg;
}
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -