/*! \file ks0108conf.h \brief Graphic LCD driver configuration. */
//*****************************************************************************
//
// File Name	: 'ks0108conf.h'
// Title		: Graphic LCD driver for HD61202/KS0108 displays
// Author		: Pascal Stang - Copyright (C) 2001-2003
// Date			: 10/19/2001
// Revised		: 5/1/2003
// Version		: 0.5
// Target MCU	: Atmel AVR
// Editor Tabs	: 4
//
// NOTE: This code is currently below version 1.0, and therefore is considered
// to be lacking in some functionality or documentation, or may not be fully
// tested.  Nonetheless, you can expect most functions to work.
//
// This code is distributed under the GNU Public License
//		which can be found at http://www.gnu.org/licenses/gpl.txt
//
//*****************************************************************************


#ifndef KS0108CONF_H
#define KS0108CONF_H

// define LCD hardware interface
// -LCD_MEMORY_INTERFACE assumes that the registers of the LCD have been mapped
// into the external memory space of the AVR processor memory bus
// -LCD_PORT_INTERFACE is a direct-connection interface from port pins to LCD
// SELECT (UNCOMMENT) ONLY ONE!

// *** NOTE: memory interface is not yet fully supported, but it might work

//#define GLCD_MEMORY_INTERFACE
#define GLCD_PORT_INTERFACE

// GLCD_PORT_INTERFACE specifics
#ifdef GLCD_PORT_INTERFACE
	// make sure these parameters are not already defined elsewhere
	#ifndef GLCD_CTRL_PORT
		#define GLCD_CTRL_PORT	PORTB	// PORT for LCD control signals
		#define GLCD_CTRL_DDR	DDRB	// DDR register of LCD_CTRL_PORT
		#define GLCD_CTRL_RS	PB0		// pin for LCD Register Select
		#define GLCD_CTRL_RW	PB1		// pin for LCD Read/Write
		#define GLCD_CTRL_E		PB2		// pin for LCD Enable
		#define GLCD_CTRL_CS0	PB3		// pin for LCD Controller 0 Chip Select
		#define GLCD_CTRL_CS1	PB4		// pin for LCD Controller 1 Chip Select(*)
		#define GLCD_CTRL_CS2	PB6		// pin for LCD Controller 2 Chip Select(*)
		#define GLCD_CTRL_CS3	PB7		// pin for LCD Controller 3 Chip Select(*)
		#define GLCD_CTRL_RESET	PB5		// pin for LCD Reset
		// (*) NOTE: additonal controller chip selects are optional and 
		// will be automatically used per each step in 64 pixels of display size
		// Example: Display with 128 hozizontal pixels uses 2 controllers
	#endif
	#ifndef GLCD_DATA_PORT
		#define GLCD_DATA_PORT	PORTC	// PORT for LCD data signals
		#define GLCD_DATA_DDR	DDRC	// DDR register of LCD_DATA_PORT
		#define GLCD_DATA_PIN	PINC	// PIN register of LCD_DATA_PORT
	#endif
#endif

// GLCD_MEMORY_INTERFACE specifics
#ifdef GLCD_MEMORY_INTERFACE
	// make sure these parameters are not already defined elsewhere
	#ifndef GLCD_CONTROLLER0_CTRL_ADDR
		// absolute address of LCD Controller #0 CTRL and DATA registers
		#define GLCD_CONTROLLER0_CTRL_ADDR	0x1000
		#define GLCD_CONTROLLER0_DATA_ADDR	0x1001
		// offset of other controllers with respect to controller0
		#define GLCD_CONTROLLER_ADDR_OFFSET	0x0002
	#endif
#endif


// LCD geometry defines (change these definitions to adapt code/settings)
#define GLCD_XPIXELS			128		// pixel width of entire display
#define GLCD_YPIXELS			64		// pixel height of entire display
#define GLCD_CONTROLLER_XPIXELS	64		// pixel width of one display controller

// Set text size of display
// These definitions are not currently used and will probably move to glcd.h
#define GLCD_TEXT_LINES           8     // visible lines
#define GLCD_TEXT_LINE_LENGTH    22     // internal line length

#endif