;*******************************************************************************
;   msp430x24x Demo - USCI_B0, SPI 3-Wire Slave Data Echo
;
;   Description: SPI slave talks to SPI master using 3-wire mode. Data received
;   from master is echoed back.  USCI RX ISR is used to handle communication,
;   CPU normally in LPM4.  Prior to initial data exchange, master pulses
;   slaves RST for complete reset.
;   ACLK = n/a, MCLK = SMCLK = DCO ~ 1048kHz
;
;   Use with SPI Master Incremented Data code example.  If the slave is in
;   debug mode, the reset signal from the master will conflict with slave's
;   JTAG; to work around, use IAR's "Release JTAG on Go" on slave device.  If
;   breakpoints are set in slave RX ISR, master must stopped also to avoid
;   overrunning slave RXBUF.
;
;                    MSP430F249
;                 -----------------
;             /|\|              XIN|-
;              | |                 |  
;     Master---|-|RST          XOUT|-
;                |                 |
;                |             P3.1|-> Data Out (UCB0SIMO)
;                |                 |
;                |             P3.2|<- Data In (UCB0SOMI)
;                |                 |
;                |             P3.3|-> Serial Clock Out (UCB0CLK)
;
;   B. Nisarga
;   Texas Instruments Inc.
;   September 2007
;   Built with IAR Embedded Workbench Version: 3.42A
;*******************************************************************************
#include "msp430x24x.h"

#define     MST_Data   R6
#define     SLV_Data   R7
;-------------------------------------------------------------------------------
            RSEG    CSTACK                  ; Define stack segment
;-------------------------------------------------------------------------------
            RSEG    CODE                    ; Assemble to Flash memory
;-------------------------------------------------------------------------------
RESET       mov.w   #SFE(CSTACK),SP         ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop watchdog timer
CheckCal    cmp.b   #0FFh,&CALBC1_1MHZ      ; Calibration constants erased?
            jeq     Trap
            cmp.b   #0FFh,&CALDCO_1MHZ
            jne     Load  
Trap        jmp     $                       ; Trap CPU!!
Load        mov.b   &CALBC1_1MHZ,&BCSCTL1   ; Set DCO to 1MHz
            mov.b   &CALDCO_1MHZ,&DCOCTL    ;                                            
waitForMstr bit.b   #08h,&P3IN              ; If clock sig from mstr stays low,
            jz      waitForMstr             ; it is not yet in SPI mode
                                            ;
SetupP3     bis.b   #00Eh,&P3SEL            ; P3.3,2,1 option select
SetupSPI    mov.b   #UCSWRST,&UCB0CTL1      ; **Put state machine in reset**
            bis.b   #UCCKPL+UCMSB+UCSYNC,&UCB0CTL0;3-pin, 8-bit SPI master
            bic.b   #UCSWRST,&UCB0CTL1      ; **Initialize USCI state machine**
            bis.b   #UCB0RXIE,&IE2          ; Enable USCI_B0 RX interrupt
                                            ;
Mainloop    bis.b   #LPM3+GIE,SR            ; Enter LPM3, enable interrupts
            nop                             ; Required for debugger only
                                            ;
;-------------------------------------------------------------------------------
USCIB0RX_ISR;       Test for valid RX and TX character
;-------------------------------------------------------------------------------
TX1         bit.b   #UCB0TXIFG,&IFG2        ; USCI_B0 TX buffer ready?
            jz      TX1                     ;
            mov.b   &UCB0RXBUF,&UCB0TXBUF   ;
            reti
;-------------------------------------------------------------------------------
            COMMON  INTVEC                  ; Interrupt Vectors
;-------------------------------------------------------------------------------
            ORG     USCIAB0RX_VECTOR        ; USCI_B0 Rx Vector
            DW      USCIB0RX_ISR            ;
            ORG     RESET_VECTOR            ; RESET Vector
            DW      RESET                   ;
            END