;******************************************************************************
;   MSP430x24x Demo - Basic Clock, LPM3 Using WDT ISR, VLO ACLK
;
;   Description: This program operates MSP430 normally in LPM3, pulsing P1.0
;   ~ 6 second intervals. WDT ISR used to wake-up system. All I/O configured
;   as low outputs to eliminate floating inputs. Current consumption does
;   increase when LED is powered on P1.0. Demo for measuring LPM3 current.
;   ACLK = VLO/2, MCLK = SMCLK = default DCO ~1.045MHz
;
;                MSP430F249
;             -----------------
;         /|\|              XIN|-
;          | |                 |
;          --|RST          XOUT|-
;            |                 |
;            |             P1.0|-->LED
;
;   B. Nisarga
;   Texas Instruments Inc.
;   September 2007
;   Built with IAR Embedded Workbench Version: 3.42A
;******************************************************************************
#include "msp430x24x.h"
;-------------------------------------------------------------------------------
            RSEG    CSTACK                  ; Define stack segment
;-------------------------------------------------------------------------------
            RSEG    CODE                    ; Assemble to Flash memory
;-------------------------------------------------------------------------------
RESET       mov.w   #SFE(CSTACK),SP         ; Initialize stackpointer
SetupWDT    mov.w   #WDT_ADLY_1000,&WDTCTL  ; WDT 1s*4 interval timer
SetupBCS    bis.b   #DIVA_1,&BCSCTL1        ; ACLK/2
            bis.b   #LFXT1S_2,&BCSCTL3      ; ACLK = VLO
            bis.b   #WDTIE,&IE1             ; Enable WDT interrupt
SetupP1     mov.b   #0FFh,&P1DIR            ; All P1.x outputs
            clr.b   &P1OUT                  ; All P1.x reset
SetupP2     clr.b   &P2SEL                  ; All P2.x GPIO function
            mov.b   #0FFh,&P2DIR            ; All P2.x outputs
            clr.b   &P2OUT                  ; All P2.x reset
SetupP3     mov.b   #0FFh,&P3DIR            ; All P3.x outputs
            clr.b   &P3OUT                  ; All P3.x reset
SetupP4     mov.b   #0FFh,&P4DIR            ; All P4.x outputs
            clr.b   &P4OUT                  ; All P4.x reset
SetupP5     mov.b   #0FFh,&P5DIR            ; All P4.x outputs
            clr.b   &P5OUT 
SetupP6     mov.b   #0FFh,&P6DIR            ; All P4.x outputs
            clr.b   &P6OUT              
Mainloop    bis.w   #LPM3+GIE,SR            ; Enter LPM3, enable interrupts
            bis.b   #001h,&P1OUT            ; Set P1.0
            push.w  #20000                   ; Delay to TOS
Delay       dec.w   0(SP)                   ; Decrement TOS
            jnz     Delay                   ; Delay over?
            incd.w  SP                      ; Clean stack
            bic.b   #001h,&P1OUT            ; Reset P1.0
            jmp     Mainloop                ; Again
                                            ;
;-------------------------------------------------------------------------------
WDT_ISR;    Exit LPM3 on reti
;-------------------------------------------------------------------------------
            bic.w   #LPM3,0(SP)             ; Clear LPM3 from TOS
            reti                            ;
                                            ;
;-------------------------------------------------------------------------------
            COMMON  INTVEC                  ; Interrupt Vectors
;-------------------------------------------------------------------------------
            ORG     WDT_VECTOR              ; WDT Vector
            DW      WDT_ISR
            ORG     RESET_VECTOR            ; POR, ext. Reset
            DW      RESET
            END