TOKENRING-MIB DEFINITIONS ::= BEGINIMPORTS    MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,    Counter32, Integer32                 FROM SNMPv2-SMI    transmission                         FROM RFC1213-MIB    MacAddress,TimeStamp                 FROM SNMPv2-TC    MODULE-COMPLIANCE, OBJECT-GROUP      FROM SNMPv2-CONF;dot5 MODULE-IDENTITY    LAST-UPDATED "9410231150Z"    ORGANIZATION "IETF Interfaces MIB Working Group"    CONTACT-INFO            "        Keith McCloghrie             Postal: cisco Systems, Inc.                     170 West Tasman Drive,                     San Jose, CA 95134-1706                     US              Phone: +1 408 526 5260              EMail: kzm@cisco.com"    DESCRIPTION        "The MIB module for IEEE Token Ring entities."    ::= { transmission 9 }--              The 802.5 Interface Table-- This table contains state and parameter information which-- is specific to 802.5 interfaces.  It is mandatory that-- systems having 802.5 interfaces implement this table in-- addition to the ifTable (see RFCs 1213 and 1573).dot5Table       OBJECT-TYPE    SYNTAX      SEQUENCE OF Dot5Entry    MAX-ACCESS  not-accessible    STATUS      current    DESCRIPTION            "This table contains Token Ring interface            parameters and state variables, one entry            per 802.5 interface."    ::= { dot5 1 }dot5Entry       OBJECT-TYPE    SYNTAX      Dot5Entry    MAX-ACCESS  not-accessible    STATUS      current    DESCRIPTION            "A list of Token Ring status and parameter             values for an 802.5 interface."    INDEX       { dot5IfIndex }    ::= { dot5Table 1 }Dot5Entry ::= SEQUENCE {     dot5IfIndex              Integer32,     dot5Commands             INTEGER,     dot5RingStatus           INTEGER,     dot5RingState            INTEGER,     dot5RingOpenStatus       INTEGER,     dot5RingSpeed            INTEGER,     dot5UpStream             MacAddress,     dot5ActMonParticipate    INTEGER,     dot5Functional           MacAddress,     dot5LastBeaconSent       TimeStamp}dot5IfIndex     OBJECT-TYPE    SYNTAX      Integer32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The value of this object identifies the             802.5 interface for which this entry             contains management information.  The             value of this object for a particular             interface has the same value as the             ifIndex object, defined in MIB-II for             the same interface."    ::= { dot5Entry 1 }dot5Commands    OBJECT-TYPE    SYNTAX      INTEGER {                    noop(1),                    open(2),                    reset(3),                    close(4)                }    MAX-ACCESS  read-write    STATUS      current    DESCRIPTION            "When this object is set to the value of             open(2), the station should go into the             open state.  The progress and success of             the open is given by the values of the             objects dot5RingState and             dot5RingOpenStatus.                 When this object is set to the value             of reset(3), then the station should do             a reset.  On a reset, all MIB counters             should retain their values, if possible.             Other side affects are dependent on the             hardware chip set.                 When this object is set to the value             of close(4), the station should go into             the stopped state by removing itself             from the ring.                 Setting this object to a value of             noop(1) has no effect.                 When read, this object always has a             value of noop(1).                 The open(2) and close(4) values             correspond to the up(1) and down(2) values             of MIB-II's ifAdminStatus and ifOperStatus,             i.e., the setting of ifAdminStatus and             dot5Commands affects the values of both             dot5Commands and ifOperStatus."    ::= { dot5Entry 2 }dot5RingStatus  OBJECT-TYPE    SYNTAX      INTEGER (0..262143)    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The current interface status which can            be used to diagnose fluctuating problems            that can occur on token rings, after a            station has successfully been added to            the ring.               Before an open is completed, this            object has the value for the 'no status'            condition.  The dot5RingState and            dot5RingOpenStatus objects provide for            debugging problems when the station            can not even enter the ring.                The object's value is a sum of            values, one for each currently applicable            condition.  The following values are            defined for various conditions:                    0 = No Problems detected                   32 = Ring Recovery                   64 = Single Station                  256 = Remove Received                  512 = reserved                 1024 = Auto-Removal Error                 2048 = Lobe Wire Fault                 4096 = Transmit Beacon                 8192 = Soft Error                16384 = Hard Error                32768 = Signal Loss               131072 = no status, open not completed."    ::= { dot5Entry 3 }dot5RingState   OBJECT-TYPE    SYNTAX      INTEGER {                    opened(1),                    closed(2),                    opening(3),                    closing(4),                    openFailure(5),                    ringFailure(6)                }    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The current interface state with respect            to entering or leaving the ring."    ::= { dot5Entry 4 }dot5RingOpenStatus  OBJECT-TYPE    SYNTAX      INTEGER {                    noOpen(1),     -- no open attempted                    badParam(2),                    lobeFailed(3),                    signalLoss(4),                    insertionTimeout(5),                    ringFailed(6),                    beaconing(7),                    duplicateMAC(8),                    requestFailed(9),                    removeReceived(10),                    open(11)      -- last open successful                }    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This object indicates the success, or the            reason for failure, of the station's most            recent attempt to enter the ring."    ::= { dot5Entry 5 }dot5RingSpeed   OBJECT-TYPE    SYNTAX      INTEGER {                    unknown(1),                    oneMegabit(2),                    fourMegabit(3),                    sixteenMegabit(4)                }    MAX-ACCESS  read-write    STATUS      current    DESCRIPTION            "The ring-speed at the next insertion into            the ring.  Note that this may or may not be            different to the current ring-speed which is            given by MIB-II's ifSpeed.  For interfaces            which do not support changing ring-speed,            dot5RingSpeed can only be set to its current            value.  When dot5RingSpeed has the value            unknown(1), the ring's actual ring-speed is            to be used."    ::= { dot5Entry 6 }dot5UpStream    OBJECT-TYPE    SYNTAX      MacAddress    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The MAC-address of the up stream neighbor             station in the ring."    ::= { dot5Entry 7 }dot5ActMonParticipate OBJECT-TYPE    SYNTAX      INTEGER {                    true(1),                    false(2)                }    MAX-ACCESS  read-write    STATUS      current    DESCRIPTION            "If this object has a value of true(1) then            this interface will participate in the            active monitor selection process.  If the            value is false(2) then it will not.            Setting this object does not take effect            until the next Active Monitor election, and            might not take effect until the next time            the interface is opened."    ::= { dot5Entry 8 }dot5Functional  OBJECT-TYPE    SYNTAX      MacAddress    MAX-ACCESS  read-write    STATUS      current    DESCRIPTION            "The bit mask of all Token Ring functional            addresses for which this interface will            accept frames."    ::= { dot5Entry 9 }dot5LastBeaconSent OBJECT-TYPE    SYNTAX      TimeStamp    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The value of MIB-II's sysUpTime object at which            the local system last transmitted a Beacon frame            on this interface."    ::= { dot5Entry 10 }--   The 802.5 Statistics Table-- This table contains statistics and error counter which are-- specific to 802.5 interfaces.  It is mandatory that systems-- having 802.5 interfaces implement this table.dot5StatsTable  OBJECT-TYPE    SYNTAX      SEQUENCE OF Dot5StatsEntry    MAX-ACCESS  not-accessible    STATUS      current    DESCRIPTION            "A table containing Token Ring statistics,            one entry per 802.5 interface.                All the statistics are defined using            the syntax Counter32 as 32-bit wrap around            counters.  Thus, if an interface's            hardware maintains these statistics in            16-bit counters, then the agent must read            the hardware's counters frequently enough            to prevent loss of significance, in order            to maintain 32-bit counters in software."    ::= { dot5 2 }dot5StatsEntry  OBJECT-TYPE    SYNTAX      Dot5StatsEntry    MAX-ACCESS  not-accessible    STATUS      current    DESCRIPTION            "An entry contains the 802.5 statistics             for a particular interface."    INDEX       { dot5StatsIfIndex }    ::= { dot5StatsTable 1 }Dot5StatsEntry ::= SEQUENCE {     dot5StatsIfIndex              Integer32,     dot5StatsLineErrors           Counter32,     dot5StatsBurstErrors          Counter32,     dot5StatsACErrors             Counter32,     dot5StatsAbortTransErrors     Counter32,     dot5StatsInternalErrors       Counter32,     dot5StatsLostFrameErrors      Counter32,     dot5StatsReceiveCongestions   Counter32,     dot5StatsFrameCopiedErrors    Counter32,     dot5StatsTokenErrors          Counter32,     dot5StatsSoftErrors           Counter32,     dot5StatsHardErrors           Counter32,     dot5StatsSignalLoss           Counter32,     dot5StatsTransmitBeacons      Counter32,     dot5StatsRecoverys            Counter32,     dot5StatsLobeWires            Counter32,     dot5StatsRemoves              Counter32,     dot5StatsSingles              Counter32,     dot5StatsFreqErrors           Counter32}dot5StatsIfIndex  OBJECT-TYPE    SYNTAX      Integer32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "The value of this object identifies the            802.5 interface for which this entry            contains management information.  The            value of this object for a particular            interface has the same value as MIB-II's            ifIndex object for the same interface."    ::= { dot5StatsEntry 1 }dot5StatsLineErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a frame            or token is copied or repeated by a            station, the E bit is zero in the frame            or token and one of the following            conditions exists: 1) there is a            non-data bit (J or K bit) between the SD            and the ED of the frame or token, or            2) there is an FCS error in the frame."    ::= { dot5StatsEntry 2 }dot5StatsBurstErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            detects the absence of transitions for five            half-bit timers (burst-five error)."    ::= { dot5StatsEntry 3 }dot5StatsACErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            receives an AMP or SMP frame in which A is            equal to C is equal to 0, and then receives            another SMP frame with A is equal to C is            equal to 0 without first receiving an AMP            frame. It denotes a station that cannot set            the AC bits properly."    ::= { dot5StatsEntry 4 }dot5StatsAbortTransErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            transmits an abort delimiter while            transmitting."    ::= { dot5StatsEntry 5 }dot5StatsInternalErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            recognizes an internal error."    ::= { dot5StatsEntry 6 }dot5StatsLostFrameErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            is transmitting and its TRR timer expires.            This condition denotes a condition where a            transmitting station in strip mode does not            receive the trailer of the frame before the            TRR timer goes off."    ::= { dot5StatsEntry 7 }dot5StatsReceiveCongestions OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            recognizes a frame addressed to its            specific address, but has no available            buffer space indicating that the station            is congested."    ::= { dot5StatsEntry 8 }dot5StatsFrameCopiedErrors OBJECT-TYPE    SYNTAX      Counter32    MAX-ACCESS  read-only    STATUS      current    DESCRIPTION            "This counter is incremented when a station            recognizes a frame addressed to its            specific address and detects that the FS