HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Counter32,Unsigned32,Gauge32,NOTIFICATION-TYPE,Integer32,transmission                  FROM SNMPv2-SMIRowStatus,TEXTUAL-CONVENTION            FROM SNMPv2-TCifIndex                       FROM IF-MIBPerfCurrentCount,PerfIntervalCount             FROM PerfHist-TC-MIBSnmpAdminString               FROM SNMP-FRAMEWORK-MIBMODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUP            FROM SNMPv2-CONF;hdsl2ShdslMIB MODULE-IDENTITY    LAST-UPDATED "200205090000Z" -- May 9, 2002    ORGANIZATION "ADSLMIB Working Group"    CONTACT-INFO "WG-email:  adslmib@ietf.org               Info:      https://www1.ietf.org/mailman/listinfo/adslmib               Chair:     Mike Sneed               Postal:    P.O. Box 37324                          Raleigh NC 27627-7324               Email:     sneedmike@hotmail.com               Co-editor: Bob Ray                          PESA Switching Systems, Inc.               Postal:    330-A Wynn Drive                          Huntsville, AL 35805 USA               Email:     rray@pesa.com               Phone:     +1 256 726 9200 ext. 142               Co-editor: Rajesh Abbi                          Alcatel USA               Postal:    2912 Wake Forest Road                          Raleigh, NC 27609-7860 USA               Email:     Rajesh.Abbi@alcatel.com               Phone:     +1 919 850 6194              "DESCRIPTION     "This MIB module defines a collection of objects for managing      HDSL2/SHDSL lines.  An agent may reside at either end of the      line, however the MIB is designed to require no management      communication between the modems beyond that inherent in the      low-level EOC line protocol as defined in ANSI T1E1.4/2000-006      (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)." REVISION "200205090000Z" -- May 9, 2002 DESCRIPTION "Initial version, published as RFC 3276." ::= { transmission 48 }hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }-- Textual Conventions used in this MIB--Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "A gauge associated with interface performance measurements in      a current 1-day (24 hour) measurement interval.      The value of this gauge starts at zero at the beginning of an      interval and is increased when associated events occur, until      the end of the 1-day interval.  At that time the value of the      gauge is stored in the previous 1-day history interval, as      defined in a companion object of type      Hdsl2Shdsl1DayIntevalCount, and the current interval gauge      is restarted at zero.      In the case where the agent has no valid data available for      this interval the corresponding object instance is not      available and upon a retrieval request a corresponding error      message shall be returned to indicate that this instance does      not exist.  Please note that zero is a valid value."   SYNTAX  Gauge32Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "A counter associated with interface performance measurements      during the most previous 1-day (24 hour) measurement interval.      The value of this gauge is equal to the value of the current      day gauge, as defined in a companion object of type      Hdsl2ShdslPerfCurrDayCount, at the end of its most recent      interval.      In the case where the agent has no valid data available for      this interval the corresponding object instance is not      available and upon a retrieval request a corresponding error      message shall be returned to indicate that this instance does      not exist."   SYNTAX  Gauge32Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "The number of seconds that have elapsed since the beginning of      the current measurement period.  If, for some reason, such as      an adjustment in the system's time-of-day clock or the addition      of a leap second, the current interval exceeds the maximum      value, the agent will return the maximum value.      For 15 minute intervals, the range is limited to (0..899).      For 24 hour intervals, the range is limited to (0..86399)."   SYNTAX    Unsigned32(0..86399)Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "This convention defines a range of values that may be set in      a fault threshold alarm control.  As the number of seconds in      a 15-minute interval numbers at most 900, objects of this type      may have a range of 0...900, where the value of 0 disables the      alarm."   SYNTAX    Unsigned32(0..900)Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "This is the unique identification for all units in a      HDSL2/SHDSL Span.  It is based on the EOC unit addressing      scheme with reference to the xtuC."   SYNTAX    INTEGER           {           xtuC(1),           xtuR(2),           xru1(3),           xru2(4),           xru3(5),           xru4(6),           xru5(7),           xru6(8),           xru7(9),           xru8(10)           }Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "This is the referenced side of a HDSL2/SHDSL unit - Network      or Customer side.  The side facing the Network is the Network      side, while the side facing the Customer is the Customer side."   SYNTAX    INTEGER           {           networkSide(1),           customerSide(2)           }Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "This is the referenced pair of wires in a HDSL2/SHDSL Segment.      HDSL2 only supports a single pair (wirePair1), while SHDSL      supports an optional second pair (wirePair2)."   SYNTAX    INTEGER           {           wirePair1(1),           wirePair2(2)           }Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "Contains the regional setting of the HDSL2/SHDSL span,     represented as a bit-map of possible settings. The various     bit positions are:     Bit   Meaning      Description     1     region 1     Indicates ITU-T G.991.2 Annex A.     2     region 2     Indicates ITU-T G.991.2 Annex B."   SYNTAX      BITS           {           region1(0),           region2(1)           }Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION   STATUS    current   DESCRIPTION     "The various STU-C symbol clock references for the     HDSL2/SHDSL span, represented as an enumeration."   SYNTAX    INTEGER          {          localClk(1),          -- Mode-1 per G991.2          networkClk(2),        -- Mode-2 per G991.2          dataOrNetworkClk(3),  -- Mode-3a per G991.2          dataClk(4)            -- Mode-3b per G991.2          }-- Span Configuration Group--hdsl2ShdslSpanConfTable OBJECT-TYPE   SYNTAX     SEQUENCE OF Hdsl2ShdslSpanConfEntry   MAX-ACCESS not-accessible   STATUS     current   DESCRIPTION     "This table supports overall configuration of HDSL2/SHDSL      Spans.  Entries in this table MUST be maintained in a      persistent manner."   ::= { hdsl2ShdslMibObjects 1 }hdsl2ShdslSpanConfEntry OBJECT-TYPE   SYNTAX      Hdsl2ShdslSpanConfEntry   MAX-ACCESS  not-accessible   STATUS      current   DESCRIPTION     "An entry in the hdsl2ShdslSpanConfTable.  Each entry      represents the complete Span in a single HDSL2/SHDSL line.      It is indexed by the ifIndex of the associated HDSL2/SHDSL      line."   INDEX { ifIndex }   ::= { hdsl2ShdslSpanConfTable 1 }Hdsl2ShdslSpanConfEntry ::=   SEQUENCE   {   hdsl2ShdslSpanConfNumRepeaters          Unsigned32,   hdsl2ShdslSpanConfProfile               SnmpAdminString,   hdsl2ShdslSpanConfAlarmProfile          SnmpAdminString   }   hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE   SYNTAX      Unsigned32(0..8)   UNITS       "repeaters"   MAX-ACCESS  read-write   STATUS      current   DESCRIPTION     "This object provisions the number of repeaters/regenerators     in this HDSL2/SHDSL Span."   ::= { hdsl2ShdslSpanConfEntry 1 }hdsl2ShdslSpanConfProfile OBJECT-TYPE   SYNTAX      SnmpAdminString (SIZE(1..32))   MAX-ACCESS  read-write   STATUS      current   DESCRIPTION     "This object is a pointer to a span configuration profile in     the hdsl2ShdslSpanConfProfileTable, which applies to this span.     The value of this object is the index of the referenced profile     in the hdsl2ShdslSpanConfProfileTable.  Note that span     configuration profiles are only applicable to SHDSL lines.     HDSL2 lines MUST reference the default profile, 'DEFVAL'.     By default, this object will have the value 'DEFVAL' (the index     of the default profile).     Any attempt to set this object to a value that is not the value     of the index for an active entry in the profile table,     hdsl2ShdslSpanConfProfileTable, MUST be rejected."   ::= { hdsl2ShdslSpanConfEntry 2 }hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE   SYNTAX      SnmpAdminString (SIZE(1..32))   MAX-ACCESS  read-write   STATUS      current   DESCRIPTION     "This object is a pointer to an Alarm configuration profile in     the hdsl2ShdslEndpointAlarmConfProfileTable.  The value of this     object is the index of the referenced profile in the     hdsl2ShdslEndpointAlarmConfProfileTable.  The alarm threshold     configuration in the referenced profile will be used by default     for all segment endpoints in this span.  Individual endpoints     may override this profile by explicitly specifying some other     profile in the hdsl2ShdslEndpointConfTable.  By default, this     object will have the value 'DEFVAL' (the index of the default     profile).     Any attempt to set this object to a value that is not the value     of the index for an active entry in the profile table,     hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."   ::= { hdsl2ShdslSpanConfEntry 3 }-- Span Status Group--hdsl2ShdslSpanStatusTable OBJECT-TYPE   SYNTAX     SEQUENCE OF Hdsl2ShdslSpanStatusEntry   MAX-ACCESS not-accessible   STATUS     current   DESCRIPTION     "This table provides overall status information of      HDSL2/SHDSL spans.  This table contains live data from      equipment.  As such, it is NOT persistent."   ::= { hdsl2ShdslMibObjects 2 }hdsl2ShdslSpanStatusEntry OBJECT-TYPE   SYNTAX      Hdsl2ShdslSpanStatusEntry   MAX-ACCESS  not-accessible   STATUS      current   DESCRIPTION     "An entry in the hdsl2ShdslSpanStatusTable.  Each entry      represents the complete span in a single HDSL2/SHDSL line.      It is indexed by the ifIndex of the associated HDSL2/SHDSL      line."   INDEX { ifIndex }   ::= { hdsl2ShdslSpanStatusTable 1 }Hdsl2ShdslSpanStatusEntry ::=   SEQUENCE   {   hdsl2ShdslStatusNumAvailRepeaters        Unsigned32,   hdsl2ShdslStatusMaxAttainableLineRate    Unsigned32,   hdsl2ShdslStatusActualLineRate           Unsigned32,   hdsl2ShdslStatusTransmissionModeCurrent             Hdsl2ShdslTransmissionModeType   }hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE   SYNTAX      Unsigned32(0..8)   MAX-ACCESS  read-only   STATUS      current   DESCRIPTION     "Contains the actual number of repeaters/regenerators      discovered in this HDSL2/SHDSL span."   ::= { hdsl2ShdslSpanStatusEntry 1 }hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE   SYNTAX      Unsigned32(0..4112000)   UNITS       "bps"   MAX-ACCESS  read-only   STATUS      current   DESCRIPTION     "Contains the maximum attainable line rate in this HDSL2/SHDSL      span.  This object provides the maximum rate the line is      capable of achieving.  This is based upon measurements made      during line probing."   ::= { hdsl2ShdslSpanStatusEntry 2 }hdsl2ShdslStatusActualLineRate OBJECT-TYPE   SYNTAX      Unsigned32(0..4112000)   UNITS       "bps"   MAX-ACCESS  read-only   STATUS      current   DESCRIPTION     "Contains the actual line rate in this HDSL2/SHDSL span.  This     should equal ifSpeed."   ::= { hdsl2ShdslSpanStatusEntry 3 }hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE   SYNTAX      Hdsl2ShdslTransmissionModeType   MAX-ACCESS  read-only   STATUS      current   DESCRIPTION     "Contains the current Power Spectral Density (PSD) regional      setting of the HDSL2/SHDSL span."   ::= { hdsl2ShdslSpanStatusEntry 4 }-- Unit Inventory Group--hdsl2ShdslInventoryTable OBJECT-TYPE   SYNTAX     SEQUENCE OF Hdsl2ShdslInventoryEntry   MAX-ACCESS not-accessible   STATUS     current   DESCRIPTION     "This table supports retrieval of unit inventory information