?? iic.c
字號(hào):
//====================================================================
// File Name : IIC.c
// Function : S3C2413 IIC-bus Master Tx/Rx mode Test Program
// (Interrupt / Non Interrupt (Polling))
// Program : Shin, On Pil (SOP)
// Date : May 21, 2002
// Version : 0.0
// History
// 0.0 : Programming start (March 11, 2002) -> SOP
//====================================================================
#include <stdio.h>
#include <stdlib.h>
#include "2413addr.h"
#include "System.h"
#include "Exception.h"
#include "Console.h"
#include "def.h"
#include "iic.h"
static U8 _iicData[IICBUFSIZE];
static volatile int _iicDataCount;
static volatile int _iicStatus;
static volatile int _iicMode;
static int _iicPt;
//===================================================================
// SMDK2413 IIC configuration
// GPE15=IICSDA, GPE14=IICSCL
// "Interrupt mode" for IIC block
//===================================================================
void * func_iic_test[][2]=
{
// "0123456789012345" max 15磊 肺茄瀝竅咯 comment竅技夸.
//IIC
(void *)Test_Iic, "IIC(KS24C080)INT",
(void *)Test_Iic2, "IIC(KS24C080)POL",
0,0
};
void Ch20_IIC(void)
{
int i;
printf("\n====== IIC Test program start ======\n");
while(1)
{
i=0;
printf("\n\n");
while(1)
{ //display menu
printf("%2d:%s",i,func_iic_test[i][1]);
i++;
if((int)(func_iic_test[i][0])==0)
{
printf("\n");
break;
}
if((i%4)==0)
printf("\n");
}
printf("\nPress Enter key to exit : ");
i = GetIntNum();
if(i==-1) break; // return.
if(i>=0 && (i<((sizeof(func_iic_test)-1)/8)) ) // select and execute...
( (void (*)(void)) (func_iic_test[i][0]) )();
}
printf("\n====== IIC Test program end ======\n");
}
//******************[ Test_Iic ]**************************************
void Test_Iic(void)
{
unsigned int i,j,save_E,save_PE;
static U8 data[256];
printf("[ IIC Test(Interrupt) using KS24C080 ]\n");
save_E = rGPECON;
save_PE = rGPEDN;
rGPEDN |= 0xc000; //Pull-up disable
rGPECON |= 0xa0000000; //GPE15:IICSDA , GPE14:IICSCL
pISR_IIC = (unsigned)IicInt;
rINTMSK &= ~(BIT_IIC);
//Enable ACK, Prescaler IICCLK=PCLK/16, Enable interrupt, Transmit clock value Tx clock=IICCLK/16
// If PCLK 50.7MHz, IICCLK = 3.17MHz, Tx Clock = 0.198MHz
rIICCON = (1<<7) | (0<<6) | (1<<5) | (0xf);
rIICADD = 0x10; //2413 slave address = [7:1]
rIICSTAT = 0x10; //IIC bus data output enable(Rx/Tx)
rIICLC = (1<<2)|(1); // Filter enable, 15 clocks SDA output delay added by junon
printf("Write test data into KS24C080\n");
for(i=0;i<256;i++)
Wr24C080(0xa0,(U8)i,i);
for(i=0;i<256;i++)
data[i] = 0;
printf("Read test data from KS24C080\n");
for(i=0;i<256;i++)
Rd24C080(0xa0,(U8)i,&(data[i]));
//Line changed 0 ~ f
for(i=0;i<16;i++)
{
for(j=0;j<16;j++)
printf("%2x ",data[i*16+j]);
printf("\n");
}
rINTMSK |= BIT_IIC;
rGPEDN = save_PE;
rGPECON = save_E;
}
//*************************[ Wr24C080 ]****************************
void Wr24C080(U32 slvAddr,U32 addr,U8 data)
{
_iicMode = WRDATA;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicData[1] = data;
_iicDataCount = 2;
rIICDS = slvAddr; //0xa0
rIICSTAT = 0xf0; //MasTx,Start
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1);
_iicMode = POLLACK;
while(1)
{
rIICDS = slvAddr;
_iicStatus = 0x100;
rIICSTAT = 0xf0; //MasTx,Start
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicStatus==0x100);
if(!(_iicStatus&0x1))
break; //When ACK is received
}
rIICSTAT = 0xd0; //Stop MasTx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Write is completed.
}
//**********************[ Rd24C080 ] ***********************************
void Rd24C080(U32 slvAddr,U32 addr,U8 *data)
{
_iicMode = SETRDADDR;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xf0; //MasTx,Start
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1);
_iicMode = RDDATA;
_iicPt = 0;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xb0; //MasRx,Start
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicDataCount!=-1);
*data = _iicData[1];
}
//-------------------------------------------------------------------------
void __irq IicInt(void)
{
U32 iicSt,i;
rSRCPND = BIT_IIC; //Clear pending bit
rINTPND = BIT_IIC;
iicSt = rIICSTAT;
if(iicSt & 0x8){} //When bus arbitration is failed.
if(iicSt & 0x4){} //When a slave address is matched with IICADD
if(iicSt & 0x2){} //When a slave address is 0000000b
if(iicSt & 0x1){} //When ACK isn't received
switch(_iicMode)
{
case POLLACK:
_iicStatus = iicSt;
break;
case RDDATA:
if((_iicDataCount--)==0)
{
_iicData[_iicPt++] = rIICDS;
rIICSTAT = 0x90; //Stop MasRx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Too long time...
//The pending bit will not be set after issuing stop condition.
break;
}
_iicData[_iicPt++] = rIICDS; //The last data has to be read with no ack.
if((_iicDataCount)==0)
rIICCON = 0x2f; //Resumes IIC operation with NOACK.
else
rIICCON = 0xaf; //Resumes IIC operation with ACK
break;
case WRDATA:
if((_iicDataCount--)==0)
{
rIICSTAT = 0xd0; //Stop MasTx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//The pending bit will not be set after issuing stop condition.
break;
}
rIICDS = _iicData[_iicPt++]; //_iicData[0] has dummy.
for(i=0;i<10;i++); //for setup time until rising edge of IICSCL
rIICCON = 0xaf; //resumes IIC operation.
break;
case SETRDADDR:
// printf("[ S%d ]",_iicDataCount);
if((_iicDataCount--)==0)
break; //IIC operation is stopped because of IICCON[4]
rIICDS = _iicData[_iicPt++];
for(i=0;i<10;i++); //For setup time until rising edge of IICSCL
rIICCON = 0xaf; //Resumes IIC operation.
break;
default:
break;
}
}
//===================================================================
// SMDK2413 IIC configuration
// GPE15=IICSDA, GPE14=IICSCL
// "Non-Interrupt" mode for IIC block
//===================================================================
//*********************[ Test_Iic2 ]*********************************
void Test_Iic2(void)
{
unsigned int i,j,save_E,save_PE;
static U8 data[256];
printf("[ IIC Test(Polling) using KS24C080 ]\n");
save_E = rGPECON;
save_PE = rGPEDN;
rGPEDN |= 0xc000; //Pull-up disable
rGPECON |= 0xa0000000; //GPE15:IICSDA , GPE14:IICSCL
//Enable ACK, Prescaler IICCLK=PCLK/16, Enable interrupt, Transmit clock value Tx clock=IICCLK/16
rIICCON = (1<<7) | (0<<6) | (1<<5) | (0xf);
rIICADD = 0x10; //2413 slave address = [7:1]
rIICSTAT = 0x10; //IIC bus data output enable(Rx/Tx)
//rIICLC = (1<<2)|(3); // Filter enable, 15 clocks SDA output delay added by junon
printf("Write test data into KS24C080\n");
for(i=0;i<256;i++)
_Wr24C080(0xa0,(U8)i,255-i);
for(i=0;i<256;i++)
data[i] = 0;
printf("Read test data from KS24C080\n");
for(i=0;i<256;i++)
_Rd24C080(0xa0,(U8)i,&(data[i]));
for(i=0;i<16;i++)
{
for(j=0;j<16;j++)
printf("%2x ",data[i*16+j]);
printf("\n");
}
rGPEDN = save_PE;
rGPECON = save_E;
}
//**************[ _Wr24C080 ]*****************************************
void _Wr24C080(U32 slvAddr,U32 addr,U8 data)
{
_iicMode = WRDATA;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicData[1] = data;
_iicDataCount = 2;
rIICDS = slvAddr; //0xa0
//Master Tx mode, Start(Write), IIC-bus data output enable
//Bus arbitration sucessful, Address as slave status flag Cleared,
//Address zero status flag cleared, Last received bit is 0
rIICSTAT = 0xf0;
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1)
Run_IicPoll();
_iicMode = POLLACK;
while(1)
{
rIICDS = slvAddr;
_iicStatus = 0x100; //To check if _iicStatus is changed
rIICSTAT = 0xf0; //Master Tx, Start, Output Enable, Sucessful, Cleared, Cleared, 0
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicStatus==0x100)
Run_IicPoll();
if(!(_iicStatus & 0x1))
break; //When ACK is received
}
rIICSTAT = 0xd0; //Master Tx condition, Stop(Write), Output Enable
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Write is completed.
}
//************************[ _Rd24C080 ]********************************
void _Rd24C080(U32 slvAddr,U32 addr,U8 *data)
{
_iicMode = SETRDADDR;
_iicPt = 0;
_iicData[0] = (U8)addr;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xf0; //MasTx,Start
//Clearing the pending bit isn't needed because the pending bit has been cleared.
while(_iicDataCount!=-1)
Run_IicPoll();
_iicMode = RDDATA;
_iicPt = 0;
_iicDataCount = 1;
rIICDS = slvAddr;
rIICSTAT = 0xb0; //Master Rx,Start
rIICCON = 0xaf; //Resumes IIC operation.
while(_iicDataCount!=-1)
Run_IicPoll();
*data = _iicData[1];
}
//**********************[ Run_IicPoll ]*********************************
void Run_IicPoll(void)
if(rIICCON & 0x10) //Tx/Rx Interrupt Enable
IicPoll();
}
//**********************[IicPoll ]**************************************
void IicPoll(void)
{
U32 iicSt,i;
iicSt = rIICSTAT;
if(iicSt & 0x8){} //When bus arbitration is failed.
if(iicSt & 0x4){} //When a slave address is matched with IICADD
if(iicSt & 0x2){} //When a slave address is 0000000b
if(iicSt & 0x1){} //When ACK isn't received
switch(_iicMode)
{
case POLLACK:
_iicStatus = iicSt;
break;
case RDDATA:
if((_iicDataCount--)==0)
{
_iicData[_iicPt++] = rIICDS;
rIICSTAT = 0x90; //Stop MasRx condition
rIICCON = 0xaf; //Resumes IIC operation.
Delay(1); //Wait until stop condtion is in effect.
//Too long time...
//The pending bit will not be set after issuing stop condition.
break;
}
_iicData[_iicPt++] = rIICDS;
//The last data has to be read with no ack.
if((_iicDataCount)==0)
rIICCON = 0x2f; //Resumes IIC operation with NOACK.
else
rIICCON = 0xaf; //Resumes IIC operation with ACK
break;
case WRDATA:
if((_iicDataCount--)==0)
{
rIICSTAT = 0xd0; //stop MasTx condition
rIICCON = 0xaf; //resumes IIC operation.
Delay(1); //wait until stop condtion is in effect.
//The pending bit will not be set after issuing stop condition.
break;
}
rIICDS = _iicData[_iicPt++]; //_iicData[0] has dummy.
for(i=0;i<10;i++); //for setup time until rising edge of IICSCL
rIICCON = 0xaf; //resumes IIC operation.
break;
case SETRDADDR:
// printf("[S%d]",_iicDataCount);
if((_iicDataCount--)==0)
{
break; //IIC operation is stopped because of IICCON[4]
}
rIICDS = _iicData[_iicPt++];
for(i=0;i<10;i++); //for setup time until rising edge of IICSCL
rIICCON = 0xaf; //resumes IIC operation.
break;
default:
break;
}
}
?? 快捷鍵說明
復(fù)制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號(hào)
Ctrl + =
減小字號(hào)
Ctrl + -