/* * (C) Copyright 2008 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. * * Wolfgang Denk <wd@denx.de> * Copyright 2004 Freescale Semiconductor. * (C) Copyright 2002,2003 Motorola,Inc. * Xianghua Xiao <X.Xiao@motorola.com> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA *//* * Socrates */#ifndef __CONFIG_H#define __CONFIG_H/* new uImage format support */#define CONFIG_FIT		1#define CONFIG_OF_LIBFDT	1#define CONFIG_FIT_VERBOSE	1 /* enable fit_format_{error,warning}() *//* High Level Configuration Options */#define CONFIG_BOOKE		1	/* BOOKE			*/#define CONFIG_E500		1	/* BOOKE e500 family		*/#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41		*/#define CONFIG_MPC8544		1#define CONFIG_SOCRATES		1#define CONFIG_PCI#define CONFIG_TSEC_ENET		/* tsec ethernet support	*/#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/#define CONFIG_BOARD_EARLY_INIT_R 1	/* Call board_early_init_r	*/#define CONFIG_FSL_LAW		1	/* Use common FSL init code *//* * Only possible on E500 Version 2 or newer cores. */#define CONFIG_ENABLE_36BIT_PHYS	1/* * sysclk for MPC85xx * * Two valid values are: *    33000000 *    66000000 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. * The board, however, can run at 66MHz.  In any event, this value * must match the settings of some switches.  Details can be found * in the README.mpc85xxads. */#ifndef CONFIG_SYS_CLK_FREQ#define CONFIG_SYS_CLK_FREQ	66666666#endif/* * These can be toggled for performance analysis, otherwise use default. */#define CONFIG_L2_CACHE			/* toggle L2 cache		*/#define CONFIG_BTB			/* toggle branch predition	*/#define CONFIG_ADDR_STREAMING		/* toggle addr streaming	*/#define CFG_INIT_DBCR DBCR_IDM		/* Enable Debug Exceptions	*/#undef	CFG_DRAM_TEST			/* memory test, takes time	*/#define CFG_MEMTEST_START	0x00400000#define CFG_MEMTEST_END		0x00C00000/* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */#define CFG_CCSRBAR_DEFAULT	0xFF700000	/* CCSRBAR Default	*/#define CFG_CCSRBAR		0xE0000000	/* relocated CCSRBAR	*/#define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*//* DDR Setup */#define CONFIG_FSL_DDR2#undef CONFIG_FSL_DDR_INTERACTIVE#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */#define CONFIG_DDR_SPD#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */#define CONFIG_MEM_INIT_VALUE	0xDeadBeef#define CFG_DDR_SDRAM_BASE	0x00000000#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE#define CONFIG_VERY_BIG_RAM#define CONFIG_NUM_DDR_CONTROLLERS	1#define CONFIG_DIMM_SLOTS_PER_CTLR	1#define CONFIG_CHIP_SELECTS_PER_CTRL	2/* I2C addresses of SPD EEPROMs */#define SPD_EEPROM_ADDRESS	0x50	/* CTLR 0 DIMM 0 */#define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*//* Hardcoded values, to use instead of SPD */#define CFG_DDR_CS0_BNDS		0x0000000f#define CFG_DDR_CS0_CONFIG		0x80010102#define CFG_DDR_TIMING_0		0x00260802#define CFG_DDR_TIMING_1		0x3935D322#define CFG_DDR_TIMING_2		0x14904CC8#define CFG_DDR_MODE			0x00480432#define CFG_DDR_INTERVAL		0x030C0100#define CFG_DDR_CONFIG_2		0x04400000#define CFG_DDR_CONFIG			0xC3008000#define CFG_DDR_CLK_CONTROL		0x03800000#define CFG_SDRAM_SIZE			256 /* in Megs *//* * Flash on the LocalBus */#define CFG_LBC_CACHE_BASE	0xf0000000	/* Localbus cacheable	 */#define CFG_FLASH0		0xFE000000#define CFG_FLASH1		0xFC000000#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH1, CFG_FLASH0 }#define CFG_LBC_FLASH_BASE	CFG_FLASH1	/* Localbus flash start	*/#define CFG_FLASH_BASE		CFG_LBC_FLASH_BASE /* start of FLASH	*/#define CFG_BR0_PRELIM		0xfe001001	/* port size 16bit	*/#define CFG_OR0_PRELIM		0xfe000030	/* 32MB Flash		*/#define CFG_BR1_PRELIM		0xfc001001	/* port size 16bit	*/#define CFG_OR1_PRELIM		0xfe000030	/* 32MB Flash		*/#define CFG_FLASH_CFI				/* flash is CFI compat.	*/#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver*/#define CFG_MAX_FLASH_BANKS	2		/* number of banks	*/#define CFG_MAX_FLASH_SECT	256		/* sectors per device	*/#undef	CFG_FLASH_CHECKSUM#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms)	*/#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms)	*/#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor	*/#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg	*/#define CFG_LBC_LBCR		0x00000000    /* LB config reg		*/#define CFG_LBC_LSRT		0x20000000    /* LB sdram refresh timer	*/#define CFG_LBC_MRTPR		0x20000000    /* LB refresh timer presc.*/#define CONFIG_L1_INIT_RAM#define CFG_INIT_RAM_LOCK	1#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address	*/#define CFG_INIT_RAM_END	0x4000		/* End used area in RAM	*/#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data*/#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256kB for Mon */#define CFG_MALLOC_LEN		(4 << 20)	/* Reserve 4 MB for malloc *//* FPGA and NAND */#define CFG_FPGA_BASE		0xc0000000#define CFG_FPGA_SIZE		0x00100000	/* 1 MB		*/#define CFG_HMI_BASE		0xc0010000#define CFG_BR3_PRELIM		0xc0001881	/* UPMA, 32-bit */#define CFG_OR3_PRELIM		0xfff00000	/* 1 MB 	*/#define CFG_NAND_BASE		(CFG_FPGA_BASE + 0x70)#define CFG_MAX_NAND_DEVICE	1#define NAND_MAX_CHIPS		1#define CONFIG_CMD_NAND/* LIME GDC */#define CFG_LIME_BASE		0xc8000000#define CFG_LIME_SIZE		0x04000000	/* 64 MB	*/#define CFG_BR2_PRELIM		0xc80018a1	/* UPMB, 32-bit	*/#define CFG_OR2_PRELIM		0xfc000000	/* 64 MB	*/#define CONFIG_VIDEO#define CONFIG_VIDEO_MB862xx#define CONFIG_CFB_CONSOLE#define CONFIG_VIDEO_LOGO#define CONFIG_VIDEO_BMP_LOGO#define CONFIG_CONSOLE_EXTRA_INFO#define VIDEO_FB_16BPP_PIXEL_SWAP#define CONFIG_VGA_AS_SINGLE_DEVICE#define CFG_CONSOLE_IS_IN_ENV#define CONFIG_VIDEO_SW_CURSOR#define CONFIG_SPLASH_SCREEN#define CONFIG_VIDEO_BMP_GZIP#define CFG_VIDEO_LOGO_MAX_SIZE	(2 << 20)	/* decompressed img *//* Serial Port */#define CONFIG_CONS_INDEX     1#undef	CONFIG_SERIAL_SOFTWARE_FIFO#define CFG_NS16550#define CFG_NS16550_SERIAL#define CFG_NS16550_REG_SIZE	1#define CFG_NS16550_CLK		get_bus_freq(0)#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)#define CONFIG_BAUDRATE         115200#define CFG_BAUDRATE_TABLE  \	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/#define CFG_HUSH_PARSER		1	/* Use the HUSH parser		*/#ifdef	CFG_HUSH_PARSER#define	CFG_PROMPT_HUSH_PS2	"> "#endif/* * I2C */#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */#define CONFIG_HARD_I2C			/* I2C with hardware support	*/#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/#define CFG_I2C_SPEED		102124	/* I2C speed and slave address	*/#define CFG_I2C_SLAVE		0x7F#define CFG_I2C_OFFSET		0x3000#define CONFIG_I2C_MULTI_BUS#define CONFIG_I2C_CMD_TREE#define CFG_I2C2_OFFSET		0x3100/* I2C RTC */#define CONFIG_RTC_RX8025		/* Use Epson rx8025 rtc via i2c	*/#define CFG_I2C_RTC_ADDR	0x32	/* at address 0x32		*//* I2C W83782G HW-Monitoring IC */#define CFG_I2C_W83782G_ADDR	0x28	/* W83782G address 		*//* I2C temp sensor *//* Socrates uses Maxim's	DS75, which is compatible with LM75 */#define CONFIG_DTT_LM75		1#define CONFIG_DTT_SENSORS	{4}		/* Sensor addresses	*/#define CFG_DTT_MAX_TEMP	125#define CFG_DTT_LOW_TEMP	-55#define CFG_DTT_HYSTERESIS	3#define CFG_EEPROM_PAGE_WRITE_BITS	4/* * General PCI * Memory space is mapped 1-1. */#define CFG_PCI_PHYS		0x80000000	/* 1G PCI TLB *//* PCI is clocked by the external source at 33 MHz */#define CONFIG_PCI_CLK_FREQ	33000000#define CFG_PCI1_MEM_BASE	0x80000000#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M			*/#define CFG_PCI1_IO_BASE	0xE2000000#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE#define CFG_PCI1_IO_SIZE	0x01000000	/* 16M			*/#if defined(CONFIG_PCI)#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/#endif	/* CONFIG_PCI */#define CONFIG_NET_MULTI	1#define CONFIG_MII		1	/* MII PHY management */#define CONFIG_TSEC1	1#define CONFIG_TSEC1_NAME	"TSEC0"#define CONFIG_TSEC3	1#define CONFIG_TSEC3_NAME	"TSEC1"#undef CONFIG_MPC85XX_FEC#define TSEC1_PHY_ADDR		0#define TSEC3_PHY_ADDR		1#define TSEC1_PHYIDX		0#define TSEC3_PHYIDX		0#define TSEC1_FLAGS		TSEC_GIGABIT#define TSEC3_FLAGS		TSEC_GIGABIT/* Options are: TSEC[0,1] */#define CONFIG_ETHPRIME		"TSEC0"#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */#define CONFIG_HAS_ETH0#define CONFIG_HAS_ETH1/* * Environment */#define CONFIG_ENV_IS_IN_FLASH	1#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env	*/#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)#define CONFIG_ENV_SIZE		0x4000#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/#define	CONFIG_TIMESTAMP		/* Print image info with ts	*//* * BOOTP options */#define CONFIG_BOOTP_BOOTFILESIZE#define CONFIG_BOOTP_BOOTPATH#define CONFIG_BOOTP_GATEWAY#define CONFIG_BOOTP_HOSTNAME/* * Command line configuration. */#include <config_cmd_default.h>#define CONFIG_CMD_DATE#define CONFIG_CMD_DHCP#define CONFIG_CMD_DTT#undef CONFIG_CMD_EEPROM#define CONFIG_CMD_I2C#define CONFIG_CMD_SDRAM#define CONFIG_CMD_MII#define CONFIG_CMD_NFS#define CONFIG_CMD_PING#define CONFIG_CMD_SNTP#define CONFIG_CMD_USB#define CONFIG_CMD_EXT2		/* EXT2 Support			*/#define CONFIG_CMD_BMP#if defined(CONFIG_PCI)    #define CONFIG_CMD_PCI#endif#undef CONFIG_WATCHDOG			/* watchdog disabled		*//* * Miscellaneous configurable options */#define CFG_LONGHELP			/* undef to save memory		*/#define CFG_LOAD_ADDR	0x2000000	/* default load address		*/#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/#if defined(CONFIG_CMD_KGDB)    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/#else    #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/#endif#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size	*/#define CFG_MAXARGS	16		/* max number of command args	*/#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/#define CFG_HZ		1000		/* decrementer freq: 1ms ticks	*//* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux	*//* * Internal Definitions * * Boot Flags */#define BOOTFLAG_COLD	0x01		/* Power-On: Boot from FLASH	*/#define BOOTFLAG_WARM	0x02		/* Software reboot		*/#if defined(CONFIG_CMD_KGDB)#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/#endif#define CONFIG_LOADADDR	 200000		/* default addr for tftp & bootm*/#define CONFIG_BOOTDELAY 1		/* -1 disables auto-boot	*/#define CONFIG_PREBOOT	"echo;"	\	"echo Welcome on the ABB Socrates Board;" \	"echo"#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs	*/#define	CONFIG_EXTRA_ENV_SETTINGS					\	"netdev=eth0\0"							\	"consdev=ttyS0\0"						\	"uboot_file=/home/tftp/syscon3/u-boot.bin\0"			\	"bootfile=/home/tftp/syscon3/uImage\0"				\	"fdt_file=/home/tftp/syscon3/socrates.dtb\0"			\	"initrd_file=/home/tftp/syscon3/uinitrd.gz\0"			\	"uboot_addr=FFFA0000\0"						\	"kernel_addr=FE000000\0"					\	"fdt_addr=FE1E0000\0"						\	"ramdisk_addr=FE200000\0"					\	"fdt_addr_r=B00000\0"						\	"kernel_addr_r=200000\0"					\	"ramdisk_addr_r=400000\0"					\	"rootpath=/opt/eldk/ppc_85xxDP\0"				\	"ramargs=setenv bootargs root=/dev/ram rw\0"			\	"nfsargs=setenv bootargs root=/dev/nfs rw "			\		"nfsroot=$serverip:$rootpath\0"				\	"addcons=setenv bootargs $bootargs "				\		"console=$consdev,$baudrate\0"				\	"addip=setenv bootargs $bootargs "				\		"ip=$ipaddr:$serverip:$gatewayip:$netmask"		\		":$hostname:$netdev:off panic=1\0"			\	"boot_nor=run ramargs addcons;"					\		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\		"tftp ${fdt_addr_r} ${fdt_file}; "			\		"run nfsargs addip addcons;"				\		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\	"update_uboot=tftp 100000 ${uboot_file};"			\		"protect off fffa0000 ffffffff;"			\		"era fffa0000 ffffffff;"				\		"cp.b 100000 fffa0000 ${filesize};"			\		"setenv filesize;saveenv\0"				\	"update_kernel=tftp 100000 ${bootfile};"			\		"era fe000000 fe1dffff;"				\		"cp.b 100000 fe000000 ${filesize};"			\		"setenv filesize;saveenv\0"				\	"update_fdt=tftp 100000 ${fdt_file};" 				\		"era fe1e0000 fe1fffff;"				\		"cp.b 100000 fe1e0000 ${filesize};"			\		"setenv filesize;saveenv\0"				\	"update_initrd=tftp 100000 ${initrd_file};" 			\		"era fe200000 fe9fffff;"				\		"cp.b 100000 fe200000 ${filesize};"			\		"setenv filesize;saveenv\0"				\	"clean_data=era fea00000 fff5ffff\0"				\	"usbargs=setenv bootargs root=/dev/sda1 rw\0" 			\	"load_usb=usb start;" 						\		"ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0"	\	"boot_usb=run load_usb usbargs addcons;"			\		"bootm ${kernel_addr_r} - ${fdt_addr};"			\		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\	""#define CONFIG_BOOTCOMMAND	"run boot_nor"/* pass open firmware flat tree */#define CONFIG_OF_LIBFDT	1#define CONFIG_OF_BOARD_SETUP	1/* USB support */#define CONFIG_USB_OHCI_NEW		1#define CONFIG_PCI_OHCI			1#define CONFIG_PCI_OHCI_DEVNO		3 /* Number in PCI list */#define CONFIG_PCI_EHCI_DEVNO		(CONFIG_PCI_OHCI_DEVNO / 2)#define CFG_USB_OHCI_MAX_ROOT_PORTS	15#define CFG_USB_OHCI_SLOT_NAME		"ohci_pci"#define CFG_OHCI_SWAP_REG_ACCESS	1#define CONFIG_DOS_PARTITION		1#define CONFIG_USB_STORAGE		1#endif	/* __CONFIG_H */