{
  /* Check the parameters */
  assert_param(IS_RCC_USBCLK_SOURCE(RCC_USBCLKSource));

  *(__IO uint32_t *) CFGR_USBPRE_BB = RCC_USBCLKSource;
}
#else
/**
  * @brief  Configures the USB OTG FS clock (OTGFSCLK).
  *   This function applies only to STM32 Connectivity line devices.
  * @param  RCC_OTGFSCLKSource: specifies the USB OTG FS clock source.
  *   This clock is derived from the PLL output.
  *   This parameter can be one of the following values:
  *     @arg  RCC_OTGFSCLKSource_PLLVCO_Div3: PLL VCO clock divided by 2 selected as USB OTG FS clock source
  *     @arg  RCC_OTGFSCLKSource_PLLVCO_Div2: PLL VCO clock divided by 2 selected as USB OTG FS clock source
  * @retval None
  */
void RCC_OTGFSCLKConfig(uint32_t RCC_OTGFSCLKSource)
{
  /* Check the parameters */
  assert_param(IS_RCC_OTGFSCLK_SOURCE(RCC_OTGFSCLKSource));

  *(__IO uint32_t *) CFGR_OTGFSPRE_BB = RCC_OTGFSCLKSource;
}
#endif /* STM32F10X_CL */ 

/**
  * @brief  Configures the ADC clock (ADCCLK).
  * @param  RCC_PCLK2: defines the ADC clock divider. This clock is derived from 
  *   the APB2 clock (PCLK2).
  *   This parameter can be one of the following values:
  *     @arg RCC_PCLK2_Div2: ADC clock = PCLK2/2
  *     @arg RCC_PCLK2_Div4: ADC clock = PCLK2/4
  *     @arg RCC_PCLK2_Div6: ADC clock = PCLK2/6
  *     @arg RCC_PCLK2_Div8: ADC clock = PCLK2/8
  * @retval None
  */
void RCC_ADCCLKConfig(uint32_t RCC_PCLK2)
{
  uint32_t tmpreg = 0;
  /* Check the parameters */
  assert_param(IS_RCC_ADCCLK(RCC_PCLK2));
  tmpreg = RCC->CFGR;
  /* Clear ADCPRE[1:0] bits */
  tmpreg &= CFGR_ADCPRE_Reset_Mask;
  /* Set ADCPRE[1:0] bits according to RCC_PCLK2 value */
  tmpreg |= RCC_PCLK2;
  /* Store the new value */
  RCC->CFGR = tmpreg;
}

#ifdef STM32F10X_CL
/**
  * @brief  Configures the I2S2 clock source(I2S2CLK).
  * @note
  *   - This function must be called before enabling I2S2 APB clock.
  *   - This function applies only to STM32 Connectivity line devices.
  * @param  RCC_I2S2CLKSource: specifies the I2S2 clock source.
  *   This parameter can be one of the following values:
  *     @arg RCC_I2S2CLKSource_SYSCLK: system clock selected as I2S2 clock entry
  *     @arg RCC_I2S2CLKSource_PLL3_VCO: PLL3 VCO clock selected as I2S2 clock entry
  * @retval None
  */
void RCC_I2S2CLKConfig(uint32_t RCC_I2S2CLKSource)
{
  /* Check the parameters */
  assert_param(IS_RCC_I2S2CLK_SOURCE(RCC_I2S2CLKSource));

  *(__IO uint32_t *) CFGR2_I2S2SRC_BB = RCC_I2S2CLKSource;
}

/**
  * @brief  Configures the I2S3 clock source(I2S2CLK).
  * @note
  *   - This function must be called before enabling I2S3 APB clock.
  *   - This function applies only to STM32 Connectivity line devices.
  * @param  RCC_I2S3CLKSource: specifies the I2S3 clock source.
  *   This parameter can be one of the following values:
  *     @arg RCC_I2S3CLKSource_SYSCLK: system clock selected as I2S3 clock entry
  *     @arg RCC_I2S3CLKSource_PLL3_VCO: PLL3 VCO clock selected as I2S3 clock entry
  * @retval None
  */
void RCC_I2S3CLKConfig(uint32_t RCC_I2S3CLKSource)
{
  /* Check the parameters */
  assert_param(IS_RCC_I2S3CLK_SOURCE(RCC_I2S3CLKSource));

  *(__IO uint32_t *) CFGR2_I2S3SRC_BB = RCC_I2S3CLKSource;
}
#endif /* STM32F10X_CL */

/**
  * @brief  Configures the External Low Speed oscillator (LSE).
  * @param  RCC_LSE: specifies the new state of the LSE.
  *   This parameter can be one of the following values:
  *     @arg RCC_LSE_OFF: LSE oscillator OFF
  *     @arg RCC_LSE_ON: LSE oscillator ON
  *     @arg RCC_LSE_Bypass: LSE oscillator bypassed with external clock
  * @retval None
  */
void RCC_LSEConfig(uint8_t RCC_LSE)
{
  /* Check the parameters */
  assert_param(IS_RCC_LSE(RCC_LSE));
  /* Reset LSEON and LSEBYP bits before configuring the LSE ------------------*/
  /* Reset LSEON bit */
  *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_OFF;
  /* Reset LSEBYP bit */
  *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_OFF;
  /* Configure LSE (RCC_LSE_OFF is already covered by the code section above) */
  switch(RCC_LSE)
  {
    case RCC_LSE_ON:
      /* Set LSEON bit */
      *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_ON;
      break;
      
    case RCC_LSE_Bypass:
      /* Set LSEBYP and LSEON bits */
      *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_Bypass | RCC_LSE_ON;
      break;            
      
    default:
      break;      
  }
}

/**
  * @brief  Enables or disables the Internal Low Speed oscillator (LSI).
  * @note   LSI can not be disabled if the IWDG is running.
  * @param  NewState: new state of the LSI. This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void RCC_LSICmd(FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  *(__IO uint32_t *) CSR_LSION_BB = (uint32_t)NewState;
}

/**
  * @brief  Configures the RTC clock (RTCCLK).
  * @note   Once the RTC clock is selected it can抰 be changed unless the Backup domain is reset.
  * @param  RCC_RTCCLKSource: specifies the RTC clock source.
  *   This parameter can be one of the following values:
  *     @arg RCC_RTCCLKSource_LSE: LSE selected as RTC clock
  *     @arg RCC_RTCCLKSource_LSI: LSI selected as RTC clock
  *     @arg RCC_RTCCLKSource_HSE_Div128: HSE clock divided by 128 selected as RTC clock
  * @retval None
  */
void RCC_RTCCLKConfig(uint32_t RCC_RTCCLKSource)
{
  /* Check the parameters */
  assert_param(IS_RCC_RTCCLK_SOURCE(RCC_RTCCLKSource));
  /* Select the RTC clock source */
  RCC->BDCR |= RCC_RTCCLKSource;
}

/**
  * @brief  Enables or disables the RTC clock.
  * @note   This function must be used only after the RTC clock was selected using the RCC_RTCCLKConfig function.
  * @param  NewState: new state of the RTC clock. This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void RCC_RTCCLKCmd(FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  *(__IO uint32_t *) BDCR_RTCEN_BB = (uint32_t)NewState;
}

/**
  * @brief  Returns the frequencies of different on chip clocks.
  * @param  RCC_Clocks: pointer to a RCC_ClocksTypeDef structure which will hold
  *   the clocks frequencies.
  * @retval None
  */
void RCC_GetClocksFreq(RCC_ClocksTypeDef* RCC_Clocks)
{
  uint32_t tmp = 0, pllmull = 0, pllsource = 0, presc = 0;

#ifdef  STM32F10X_CL
  uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0;
#endif /* STM32F10X_CL */
    
  /* Get SYSCLK source -------------------------------------------------------*/
  tmp = RCC->CFGR & CFGR_SWS_Mask;
  
  switch (tmp)
  {
    case 0x00:  /* HSI used as system clock */
      RCC_Clocks->SYSCLK_Frequency = HSI_Value;
      break;
    case 0x04:  /* HSE used as system clock */
      RCC_Clocks->SYSCLK_Frequency = HSE_Value;
      break;
    case 0x08:  /* PLL used as system clock */

      /* Get PLL clock source and multiplication factor ----------------------*/
      pllmull = RCC->CFGR & CFGR_PLLMull_Mask;
      pllsource = RCC->CFGR & CFGR_PLLSRC_Mask;
      
#ifndef STM32F10X_CL      
      pllmull = ( pllmull >> 18) + 2;
      
      if (pllsource == 0x00)
      {/* HSI oscillator clock divided by 2 selected as PLL clock entry */
        RCC_Clocks->SYSCLK_Frequency = (HSI_Value >> 1) * pllmull;
      }
      else
      {/* HSE selected as PLL clock entry */
        if ((RCC->CFGR & CFGR_PLLXTPRE_Mask) != (uint32_t)RESET)
        {/* HSE oscillator clock divided by 2 */
          RCC_Clocks->SYSCLK_Frequency = (HSE_Value >> 1) * pllmull;
        }
        else
        {
          RCC_Clocks->SYSCLK_Frequency = HSE_Value * pllmull;
        }
      }
#else
      pllmull = pllmull >> 18;
      
      if (pllmull != 0x0D)
      {
         pllmull += 2;
      }
      else
      { /* PLL multiplication factor = PLL input clock * 6.5 */
        pllmull = 13 / 2; 
      }
            
      if (pllsource == 0x00)
      {/* HSI oscillator clock divided by 2 selected as PLL clock entry */
        RCC_Clocks->SYSCLK_Frequency = (HSI_Value >> 1) * pllmull;
      }
      else
      {/* PREDIV1 selected as PLL clock entry */
        
        /* Get PREDIV1 clock source and division factor */
        prediv1source = RCC->CFGR2 & CFGR2_PREDIV1SRC;
        prediv1factor = (RCC->CFGR2 & CFGR2_PREDIV1) + 1;
        
        if (prediv1source == 0)
        { /* HSE oscillator clock selected as PREDIV1 clock entry */
          RCC_Clocks->SYSCLK_Frequency = (HSE_Value / prediv1factor) * pllmull;          
        }
        else
        {/* PLL2 clock selected as PREDIV1 clock entry */
          
          /* Get PREDIV2 division factor and PLL2 multiplication factor */
          prediv2factor = ((RCC->CFGR2 & CFGR2_PREDIV2) >> 4) + 1;
          pll2mull = ((RCC->CFGR2 & CFGR2_PLL2MUL) >> 8 ) + 2; 
          RCC_Clocks->SYSCLK_Frequency = (((HSE_Value / prediv2factor) * pll2mull) / prediv1factor) * pllmull;                         
        }
      }
#endif /* STM32F10X_CL */ 
      break;

    default:
      RCC_Clocks->SYSCLK_Frequency = HSI_Value;
      break;
  }

  /* Compute HCLK, PCLK1, PCLK2 and ADCCLK clocks frequencies ----------------*/
  /* Get HCLK prescaler */
  tmp = RCC->CFGR & CFGR_HPRE_Set_Mask;
  tmp = tmp >> 4;
  presc = APBAHBPrescTable[tmp];
  /* HCLK clock frequency */
  RCC_Clocks->HCLK_Frequency = RCC_Clocks->SYSCLK_Frequency >> presc;
  /* Get PCLK1 prescaler */
  tmp = RCC->CFGR & CFGR_PPRE1_Set_Mask;
  tmp = tmp >> 8;
  presc = APBAHBPrescTable[tmp];
  /* PCLK1 clock frequency */
  RCC_Clocks->PCLK1_Frequency = RCC_Clocks->HCLK_Frequency >> presc;
  /* Get PCLK2 prescaler */
  tmp = RCC->CFGR & CFGR_PPRE2_Set_Mask;
  tmp = tmp >> 11;
  presc = APBAHBPrescTable[tmp];
  /* PCLK2 clock frequency */
  RCC_Clocks->PCLK2_Frequency = RCC_Clocks->HCLK_Frequency >> presc;
  /* Get ADCCLK prescaler */
  tmp = RCC->CFGR & CFGR_ADCPRE_Set_Mask;
  tmp = tmp >> 14;
  presc = ADCPrescTable[tmp];
  /* ADCCLK clock frequency */
  RCC_Clocks->ADCCLK_Frequency = RCC_Clocks->PCLK2_Frequency / presc;
}

/**
  * @brief  Enables or disables the AHB peripheral clock.
  * @param  RCC_AHBPeriph: specifies the AHB peripheral to gates its clock.
  *   
  *   For @b STM32_Connectivity_line_devices, this parameter can be any combination
  *   of the following values:        
  *     @arg RCC_AHBPeriph_DMA1
  *     @arg RCC_AHBPeriph_DMA2
  *     @arg RCC_AHBPeriph_SRAM
  *     @arg RCC_AHBPeriph_FLITF
  *     @arg RCC_AHBPeriph_CRC
  *     @arg RCC_AHBPeriph_OTG_FS    
  *     @arg RCC_AHBPeriph_ETH_MAC   
  *     @arg RCC_AHBPeriph_ETH_MAC_Tx
  *     @arg RCC_AHBPeriph_ETH_MAC_Rx
  * 
  *   For @b other_STM32_devices, this parameter can be any combination of the 
  *   following values:        
  *     @arg RCC_AHBPeriph_DMA1
  *     @arg RCC_AHBPeriph_DMA2
  *     @arg RCC_AHBPeriph_SRAM
  *     @arg RCC_AHBPeriph_FLITF
  *     @arg RCC_AHBPeriph_CRC
  *     @arg RCC_AHBPeriph_FSMC
  *     @arg RCC_AHBPeriph_SDIO
  *   
  * @note SRAM and FLITF clock can be disabled only during sleep mode.
  * @param  NewState: new state of the specified peripheral clock.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void RCC_AHBPeriphClockCmd(uint32_t RCC_AHBPeriph, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_RCC_AHB_PERIPH(RCC_AHBPeriph));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    RCC->AHBENR |= RCC_AHBPeriph;
  }
  else
  {
    RCC->AHBENR &= ~RCC_AHBPeriph;
  }
}

/**
  * @brief  Enables or disables the High Speed APB (APB2) peripheral clock.
  * @param  RCC_APB2Periph: specifies the APB2 peripheral to gates its clock.
  *   This parameter can be any combination of the following values:
  *     @arg RCC_APB2Periph_AFIO, RCC_APB2Periph_GPIOA, RCC_APB2Periph_GPIOB,
  *          RCC_APB2Periph_GPIOC, RCC_APB2Periph_GPIOD, RCC_APB2Periph_GPIOE,
  *          RCC_APB2Periph_GPIOF, RCC_APB2Periph_GPIOG, RCC_APB2Periph_ADC1,
  *          RCC_APB2Periph_ADC2, RCC_APB2Periph_TIM1, RCC_APB2Periph_SPI1,
  *          RCC_APB2Periph_TIM8, RCC_APB2Periph_USART1, RCC_APB2Periph_ADC3
  * @param  NewState: new state of the specified peripheral clock.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void RCC_APB2PeriphClockCmd(uint32_t RCC_APB2Periph, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_RCC_APB2_PERIPH(RCC_APB2Periph));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    RCC->APB2ENR |= RCC_APB2Periph;
  }
  else
  {