#include "GloblDef.h"
#include "key.h"

struct SKeyValue xdata KeyValue[KEY_NUM]={	
	{1,{0}},	//功能鍵1	KEY_FUN1
	{1,{1}},	//退格鍵	KEY_C
	{1,{2}},	//功能鍵2	KEY_FUN2
	{2,{'1','.'}},
	{4,{'2','a','b','c'}},
	{4,{'3','d','e','f'}},
	{4,{'4','g','h','i'}},
	{4,{'5','j','k','l'}},
	{4,{'6','m','n','o'}},
	{5,{'7','p','q','r','s'}},
	{4,{'8','t','u','v'}},
	{5,{'9','w','x','y','z'}},
	{1,{'0'}}
};

BYTE xdata ScanKeyInterval;				//鍵掃描時間
BYTE xdata PreTimeKeyPressed;				//上一次鍵是否按下
BYTE xdata WhichKey;						//按下了什么鍵
BYTE xdata IndexInWhichKey;				//采用這個鍵的第幾個鍵值
BYTE xdata TimeIntervalOfNoKeyPress;	//沒有鍵按下的時間間隔
BYTE xdata KeyOutPort _at_ KEY_ADDRESS;

sbit KeyPort0 = KEY_PORT0;
sbit KeyPort1 = KEY_PORT1;

void KeyInitial()
{
	ScanKeyInterval = 0;
	PreTimeKeyPressed = FALSE;
	WhichKey = 0;
	IndexInWhichKey = 0;
	TimeIntervalOfNoKeyPress = 0;
}
												//是否處于按下狀態
BYTE IsKeyPressed()
{
												//373給高低電平
	KeyOutPort = 0;
	KeyPort0 = 1;
	KeyPort1 = 1;
												//輸入端口是否出現 0
	if(KeyPort0 == 0 || KeyPort1 == 0)
		return TRUE;
	else
		return FALSE;
}

BYTE GetKey()
{
	BYTE i,veil;
	KeyPort0 = 1;
	KeyPort1 = 1;
												//假設鍵值，port0為0－7，port1為8－15
	for(i = 0, veil = 0xFE; i < 8; i++, veil <<= 1)
	{
		KeyOutPort = veil;
		if(KeyPort0 == 0 || KeyPort1 == 0)
			break;
	}
	if(KeyPort1 == 0)
		i += 8;
	return i;
}
											// 返回ASCII碼
BYTE GetKeyValue()
{
	return KeyValue[WhichKey].value[IndexInWhichKey];
}

BYTE ScanKey()
{
	BYTE tWhichKey;
											//檢測是否ScanKeyInterval==0
	if(ScanKeyInterval != 0)
		return SCAN_KEY_NO_KEY_PRESSED;
	else
	{
		#ifdef KEY_DEBUG
		printf(".");
		#endif
					//是則表明從上次檢測到鍵盤按下一個SCAN_KEY_INTERVAL時間已到
					//將ScanKeyInterval置成SCAN_KEY_INTERVAL
		ScanKeyInterval = SCAN_KEY_INTERVAL;

		tWhichKey = GetKey();

					//檢測鍵盤是否按下，而且鍵值要有效（防止后面出錯）
		if(IsKeyPressed() && (tWhichKey >= 0 && tWhichKey < KEY_NUM))
		{
			#ifdef KEY_DEBUG
			printf("\npressed");
			#endif
					//檢測PreTimeKeyPressed是否為0
			if(PreTimeKeyPressed == TRUE)
			{
				return SCAN_KEY_NO_KEY_PRESSED;
			}
			else
			{
							//是則表明這是一次新的按下
				#ifdef KEY_DEBUG
				printf("\nagain");
				#endif
				PreTimeKeyPressed = TRUE;
				
				if(tWhichKey == WhichKey && TimeIntervalOfNoKeyPress > 0)
				{
					#ifdef KEY_DEBUG
					printf("\nshift");
					#endif
																//是，改變鍵值
					IndexInWhichKey++;
					if(IndexInWhichKey == KeyValue[WhichKey].ValueNum)
						IndexInWhichKey = 0;
					
					TimeIntervalOfNoKeyPress = TIME_INTERVAL_CHANGE_KEY_VALUE;	
					return SCAN_KEY_CHANGE_KEY_VALUE;
				}
				else
				{
													//否，新的鍵
					WhichKey = tWhichKey;
					IndexInWhichKey = 0;
					
					TimeIntervalOfNoKeyPress = TIME_INTERVAL_CHANGE_KEY_VALUE;	
					return SCAN_KEY_NEW_KEY_PRESSED;
				}
			}	
		}
		else
		{
											//將PreTimeKeyPressed置0
			PreTimeKeyPressed = FALSE;
								//TimeIntervalOfNoKeyPress減一，最小到0
			if(TimeIntervalOfNoKeyPress > 0)
				TimeIntervalOfNoKeyPress--;
			return SCAN_KEY_NO_KEY_PRESSED;
		}
	}