#include <C8051F330.h>

//sfr16 TMR3RL = 0x92;                        //定時器3重裝載寄存器
//sfr16 TMR3 = 0x94;                          //定時器3計數器

#define uchar unsigned char
#define uint unsigned int


//----------------------------------------------------------------------
//參數設置區
//----------------------------------------------------------------------
#define BAUDRATE 9600                              //波特率bps
#define CLKOUT 11059200                 //外部晶振,修改也要修改OSCXCN
#define SMODVAL 0                                   //SMOD的值,修改請也修改PCONVAL
#define PCONVAL 0x00                                //PCON的值,=0x00時SMOD0=0; =0x80時SMOD0=1
#define TXVAL (256-CLKOUT*(SMODVAL+1)/BAUDRATE/384)        //定時器初值
#define MAX_LEN 10                               //每次接收/發送字符串的長度

//---------------------------------------------------------------------
//全局變量
//---------------------------------------------------------------------
sbit LED = P0^6;                             //LED \'1\'亮 \'0\'滅
bit  readFlag = 0;                           //讀標志
uchar readCounts = 0;                        //已經讀取的字符個數,與MAX_LEN比較
uchar checksum;
uchar count3 ;

uchar idata trdata[MAX_LEN];                 //要接收/發送的字符串
uint k;
//----------------------------------------------------------------------
//子函數聲明
//----------------------------------------------------------------------
void SYSCLK_Init(void);                      //系統時鐘初始化
void PORT_Init(void);                        //端口初始化
void UART0_Init(void);                       //串口UART0初始化
void Send_Char(uchar ch);                    //發送單個字符
void Send_String(uchar * str, uint len);     //發送一個字符串
void UART0_ISR();                            //串口中斷服務程序,接收字符

//----------------------------------------------------------------------
//主函數
//----------------------------------------------------------------------
void main(void)
{

   PCA0MD &= ~0x40;                          //禁止看門狗
   SYSCLK_Init();                            //時鐘初始化
   PORT_Init();                              //端口初始化
   UART0_Init();                             //串口初始化                                           
   EA = 1;                                   //開全局中斷
   while(1)
   {
      if(readFlag)                           //已經讀取
      {
       readFlag = 0;                         //清零
       Send_String(trdata,MAX_LEN);          //發送字符串
      }
   }
}

//----------------------------------------------------------------------
//子函數具體實現
//----------------------------------------------------------------------

//系統時鐘初始化
/*void SYSCLK_Init (void)
{
   OSCICN |= 0x03;                     // 配置內部振蕩器的的最大頻率
                                       
   RSTSRC  = 0x04;                     // 使能始終丟失檢測寄存器

}*/
//系統時鐘初始化
void SYSCLK_Init(void)
{
   uint i;
   OSCXCN = 0x67;                            //采用外部晶振22.1184MHz,不分頻. 選型OSCXCN=0110,0111
   for(i=0;i<256;i++);                       //等待>1ms
   while(!(OSCXCN&0x80));
                                              //查詢直到XTLVLD=1,晶振穩定
   OSCICN = 0x88;                            //切換到外部振蕩器,允許時鐘失效監測器. OSCICN=1000,1000
}

/*void SYSCLK_Init(void)
{
  OSCICN    = 0x83;
}*/

//端口初始化
void PORT_Init(void)
{
   P0SKIP  = 0x0C;
   XBR0 = 0x01;                             //允許UART0,RX,TX連到2個端口引腳. XBR0=0000,0100
   XBR1 = 0x40;
   P0MDOUT |= 0x10;
}

//串口初始化
void UART0_Init(void)

{
   CKCON = 0x00;
   SCON0 = 0x50;
   TCON = 0x40;                          
   TMOD = 0x20;                             //選擇T1,方式2,自動再裝入8位計數器
   TH1 = (int)TXVAL;
   TL1 = (int)TXVAL;
  // IE|=0x10;
  // IP|=0x10;
  // RI0=0;                      
  
   ES0 = 1;                                 //UART0中斷開啟
   TR1 = 1;                                 //啟動定時器T1
   PCON |= PCONVAL;                         //PCON=0x00,SMOD = 0 ; PCON=0x80,SMOD=1
   TI0 = 1;                                 //聲明TX0就緒,可以發送
   TR0 = 1;

}

 

//發送單個字符
void Send_Char(uchar ch)
{
   
 SBUF0 = ch;                             //送入緩沖區
 while(TI0 == 0);                        //等待發送完畢
 TI0 = 0;                                //軟件清零

}

//發送字符串,調用Send_Char() len字符串長度
void Send_String(uchar * str,uint len)
{
    uint k = 0;
    do
    {
        Send_Char(*(str + k));
        k++;
    } while(k < len);
 
}


//UART0中斷服務程序. 接收字符
void UART0_ISR(void) interrupt 4 using 1
{
   uchar rxch;
   if(RI0)                                   //中斷標志 RI0=1 數據完整接收
   {
     RI0 = 0;                              //軟件清零
     rxch = SBUF0;                         //讀緩沖
   if(readCounts>=MAX_LEN)
    {
      readCounts = 0;
      readFlag = 1;
    }
  
    trdata[readCounts] = rxch;          //存入數組,供發送
    readCounts++;
 }
}
/*void serial () interrupt 4 using 1
{   if (RI0)
   {
   unsigned char ch;
        RI0 = 0;
        ch=SBUF0;
        if(ch>127)
        {
             count3=0;
             trdata[count3]=ch;
             checksum= ch-128;
        }
        else
        {
             count3++;
             trdata[count3]=ch;
             checksum ^= ch;
   
             if( (count3==(MAX_LEN-1)) && (!checksum) )
             {
                 readFlag=1;  //如果串口接收的數據達到INBUF_LEN個，且校驗沒錯，
                               //就置位取數標志
             }
        }
    }
}*/