#ifndef _LINUX_FDREG_H#define _LINUX_FDREG_H/* * This file contains some defines for the floppy disk controller. * Various sources. Mostly "IBM Microcomputers: A Programmers * Handbook", Sanches and Canton. *//* Fd controller regs. S&C, about page 340 */#define FD_STATUS	0x3f4#define FD_DATA		0x3f5#define FD_DOR		0x3f2		/* Digital Output Register */#define FD_DIR		0x3f7		/* Digital Input Register (read) */#define FD_DCR		0x3f7		/* Diskette Control Register (write)*//* Bits of main status register */#define STATUS_BUSYMASK	0x0F		/* drive busy mask */#define STATUS_BUSY	0x10		/* FDC busy */#define STATUS_DMA	0x20		/* 0- DMA mode */#define STATUS_DIR	0x40		/* 0- cpu->fdc */#define STATUS_READY	0x80		/* Data reg ready *//* Bits of FD_ST0 */#define ST0_DS		0x03		/* drive select mask */#define ST0_HA		0x04		/* Head (Address) */#define ST0_NR		0x08		/* Not Ready */#define ST0_ECE		0x10		/* Equipment chech error */#define ST0_SE		0x20		/* Seek end */#define ST0_INTR	0xC0		/* Interrupt code mask *//* Bits of FD_ST1 */#define ST1_MAM		0x01		/* Missing Address Mark */#define ST1_WP		0x02		/* Write Protect */#define ST1_ND		0x04		/* No Data - unreadable */#define ST1_OR		0x10		/* OverRun */#define ST1_CRC		0x20		/* CRC error in data or addr */#define ST1_EOC		0x80		/* End Of Cylinder *//* Bits of FD_ST2 */#define ST2_MAM		0x01		/* Missing Addess Mark (again) */#define ST2_BC		0x02		/* Bad Cylinder */#define ST2_SNS		0x04		/* Scan Not Satisfied */#define ST2_SEH		0x08		/* Scan Equal Hit */#define ST2_WC		0x10		/* Wrong Cylinder */#define ST2_CRC		0x20		/* CRC error in data field */#define ST2_CM		0x40		/* Control Mark = deleted *//* Bits of FD_ST3 */#define ST3_HA		0x04		/* Head (Address) */#define ST3_TZ		0x10		/* Track Zero signal (1=track 0) */#define ST3_WP		0x40		/* Write Protect *//* Values for FD_COMMAND */#define FD_RECALIBRATE		0x07	/* move to track 0 */#define FD_SEEK			0x0F	/* seek track */#define FD_READ			0xE6	/* read with MT, MFM, SKip deleted */#define FD_WRITE		0xC5	/* write with MT, MFM */#define FD_SENSEI		0x08	/* Sense Interrupt Status */#define FD_SPECIFY		0x03	/* specify HUT etc */#define FD_FORMAT		0x4D	/* format one track */#define FD_VERSION		0x10	/* get version code */#define FD_CONFIGURE		0x13	/* configure FIFO operation */#define FD_PERPENDICULAR	0x12	/* perpendicular r/w mode *//* DMA commands */#define DMA_READ	0x46#define DMA_WRITE	0x4A/* FDC version return types */#define FDC_TYPE_STD	0x80	/* normal 8272A clone FDC */#define FDC_TYPE_82077	0x90	/* FIFO + perpendicular support */#endif