?? w5100.h
字號:
#define S_RX_SIZE 2048 /*定義Socket接收緩沖區的大小，可以根據W5100_RMSR的設置修改 */
#define S_TX_SIZE 2048 /*定義Socket發送緩沖區的大小，可以根據W5100_TMSR的設置修改 */
//W5100 Register definition
#define COMMON_BASE 0x0000 //Base address，根據需要修改
//-----------------------------------------------------------------------------
// Common register
//-----------------------------------------------------------------------------
//Mode register, R/W, Default=0x00
#define W5100_MODE COMMON_BASE
#define MODE_RST 0x80 //Software reset
#define MODE_MT 0x20 //Memory test
#define MODE_PB 0x10 //Ping block mode
#define MODE_PPPOE 0x08 //PPOE mode
#define MODE_LB 0x04 //Little_endian/Big_endian ordering in indirect bus I/F
#define MODE_AI 0x02 //Address auto increment in indirect bus I/F
#define MODE_IND 0x01 //Indirect bus I/F mode
//Gateway address register, R/W, default=0x00
#define W5100_GAR COMMON_BASE+0x01
//Subnet mask address, R/W, default=0x00
#define W5100_SUBR COMMON_BASE+0x05
//Source hardware address, R/W, default=0x00
#define W5100_SHAR COMMON_BASE+0x09
//Source IP address, R/W, default=0x00
#define W5100_SIPR COMMON_BASE+0x0f
//Interrupt and interrupt mask register
#define W5100_IR COMMON_BASE+0x15 //RO, Default=0x00
#define IR_CONFLICT 0x80 //IP conflict
#define IR_UNREACH 0x40 //Destination unreachable
#define IR_PPPOE 0x20 //PPOE close
#define IR_S3_INT 0x08 //Occurrence of socket 3 socket interrupt
#define IR_S2_INT 0x04 //Occurrence of socket 2 socket interrupt
#define IR_S1_INT 0x02 //Occurrence of socket 1 socket interrupt
#define IR_S0_INT 0x01 //Occurrence of socket 0 socket interrupt
#define W5100_IMR COMMON_BASE+0x16 //R/W, Default=0x00
#define IMR_CONFLICT 0x80 //IP conflict
#define IMR_UNREACH 0x40 //Destination unreachable
#define IMR_PPPOE 0x20 //PPOE close
#define IMR_S3_INT 0x08 //Occurrence of socket 3 socket interrupt
#define IMR_S2_INT 0x04 //Occurrence of socket 2 socket interrupt
#define IMR_S1_INT 0x02 //Occurrence of socket 1 socket interrupt
#define IMR_S0_INT 0x01 //Occurrence of socket 0 socket interrupt
//Retry time value. Value 1 means 100us, R/W, default=0x07D0
#define W5100_RTR COMMON_BASE+0x17
//Retry count, R/W, Default=0x08
#define W5100_RCR COMMON_BASE+0X19
//RX memory size register, R/W, default=0x55
//-------------------------------------------------------- S1 S0 Memory size
// Socket3 | Socket2 | Socket1 | Socket0 | 0 0 1KB
//-------------|-------------|-------------|-------------| 0 1 2KB
//S1 S0 |S1 S0 |S1 S0 |S1 S0 | 1 0 4KB
//-------------------------------------------------------- 1 1 8KB
#define W5100_RMSR COMMON_BASE+0x1a
//TX memory size register, R/W, default=0x55
#define W5100_TMSR COMMON_BASE+0x1b
//Authentication type in PPPOE mode, R, default=0x0000
#define W5100_PATR COMMON_BASE+0x1c
//PPP LCP request timer register, R/W, default=0x28
//Value 1 is about 25ms
#define W5100_PTIMER COMMON_BASE+0x28
//PPP LCP magic number register, R/W, default=0x00
#define W5100_PMAGIC COMMON_BASE+0x29
//Unreachable IP address, RO, default=0x00
#define W5100_UIPR COMMON_BASE+0x2a
//Unreachable port register, RO, default=0x0000
#define W5100_UPORT COMMON_BASE+0x2e
//-----------------------------------------------------------------------------
// Socket register
//-----------------------------------------------------------------------------
//Socket mode register, R/W, default=0x00
#define W5100_S0_MR COMMON_BASE+0x0400 //Socket 0
#define W5100_S1_MR COMMON_BASE+0x0500 //Socket 1
#define W5100_S2_MR COMMON_BASE+0x0600 //Socket 2
#define W5100_S3_MR COMMON_BASE+0x0700 //Socket 3
#define S_MR_MULTI 0x80 //Multcasting
#define S_MR_MC 0x20 //Multcast
// P3 P2 P1 P0 Meaning
#define S_MR_CLOSED 0x00 // 0 0 0 0 Closed
#define S_MR_TCP 0x01 // 0 0 0 1 TCP
#define S_MR_UDP 0x02 // 0 0 1 0 UDP
#define S_MR_IPRAW 0x03 // 0 0 1 1 IPRAW
#define S_MR_MACRAW 0x04 // 0 1 0 0 MACRAW
#define S_MR_PPPOE 0x05 // 0 1 0 1 PPPOE
//Socket command register, R/W, default=0x00
#define W5100_S0_CR COMMON_BASE+0x0401 //Socket 0
#define W5100_S1_CR COMMON_BASE+0x0501 //Socket 1
#define W5100_S2_CR COMMON_BASE+0x0601 //Socket 2
#define W5100_S3_CR COMMON_BASE+0x0701 //Socket 3
#define S_CR_OPEN 0x01 //It is used to initialize the socket
#define S_CR_LISTEN 0x02 //In TCP mode, it waits for a connection request from any remote
//peer(Client)
#define S_CR_CONNECT 0x04 //In TCP mode, it sends a connection request to remote peer(SERVER)
#define S_CR_DISCON 0x08 //In TCP mode, it sends a connection termination request
#define S_CR_CLOSE 0x10 //Used to close the socket
#define S_CR_SEND 0x20 //It transmit the data as much as the increase size of write pointer
#define S_CR_SEND_MAC 0x21 //In UDP mode, same as SEND
#define S_CR_SEND_KEEP 0x22 //In TCP mode
#define S_CR_RECV 0x40 //Receiving is processed including the value of socket RX read
//pointer register
/* Definition for PPPOE */
#define S_CR_PCON 0x23 //Start of ADSL connection
#define S_CR_PDISCON 0x24 //End of ADSL connection
#define S_CR_PCR 0x25 //Send REQ message ineach phase
#define S_CR_PCN 0x26 //Send NAK message in each phase
#define S_CR_PCJ 0x27 //Senf REJECT message in each phase
//Socket interrup register, RO, default=0x00
#define W5100_S0_IR COMMON_BASE+0x0402 //Socket 0
#define W5100_S1_IR COMMON_BASE+0x0502 //Socket 1
#define W5100_S2_IR COMMON_BASE+0x0602 //Socket 2
#define W5100_S3_IR COMMON_BASE+0x0702 //Socket 3
#define S_IR_SENDOK 0x10 //Send data complete
#define S_IR_TIMEOUT 0x08 //Set if timeout occurs during connection or termination
//or data transmission
#define S_IR_RECV 0x04 //Set if data is received
#define S_IR_DISCON 0x02 //Set if receiv connection termination request
#define S_IR_CON 0x01 //Set if connetion is established
/* Definition for PPPOE */
#define S_IR_PRECV 0x80 //Indicate receiving no support option data
#define S_IR_PFAIL 0x40 //Indicate PAP Authentication fail
#define S_IR_PNEXT 0x20 //Go next phase
//Socket status register, RO, default=0x00
#define W5100_S0_SSR COMMON_BASE+0x0403 //Socket 0
#define W5100_S1_SSR COMMON_BASE+0x0503 //Socket 1
#define W5100_S2_SSR COMMON_BASE+0x0603 //Socket 2
#define W5100_S3_SSR COMMON_BASE+0x0703 //Socket 3
#define S_SSR_CLOSED 0x00 //In case that OPEN command are given to Sn_CR, Timeout interrupt
//is asserted or connection is terminated
#define S_SSR_INIT 0x13 //In case that Sn_MR is set as TCP and OPEN commands are given to Sn_CR
#define S_SSR_LISTEN 0x14 //In case that under the SOCK_INIT status, LISTEN commands
//are given to Sn_CR
#define S_SSR_ESTABLISHED 0x17 //In case that connection is established
#define S_SSR_CLOSE_WAIT 0x1c //In case that connection temination request is received
#define S_SSR_UDP 0x22 //In case that OPEN command is given to Sn_CR when Sn_MR is set as UDP
#define S_SSR_IPRAW 0x32 //In case that OPEN command is given to Sn_CR when Sn_MR is set as IPRAW
#define S_SSR_MACRAW 0x42 //In case that OPEN command is given to S0_CR when S0_MR is set as MACRAW
#define S_SSR_PPPOE 0x5f //In case that OPEN command is given to S0_CR when S0_MR is set as PPPOE
//Below is shown in the status change, and does not need much attention
#define S_SSR_SYNSEND 0x15
#define S_SSR_SYNRECV 0x16
#define S_SSR_FIN_WAIT 0x18
#define S_SSR_CLOSING 0x1a
#define S_SSR_TIME_WAIT 0x1b
#define S_SSR_LAST_ACK 0x1d
#define S_SSR_ARP0 0x11
#define S_SSR_ARP1 0x21
#define S_SSR_ARP2 0x31
//Socket Source port register, R/W, default=0x00
#define W5100_S0_PORT COMMON_BASE+0x0404 //Socket 0
#define W5100_S1_PORT COMMON_BASE+0x0504 //Socket 1
#define W5100_S2_PORT COMMON_BASE+0x0604 //Socket 2
#define W5100_S3_PORT COMMON_BASE+0x0704 //Socket 3
//Socket destination hardware address register, R/W, default=0x00
#define W5100_S0_DHAR COMMON_BASE+0x0406 //Socket 0
#define W5100_S1_DHAR COMMON_BASE+0x0506 //Socket 1
#define W5100_S2_DHAR COMMON_BASE+0x0606 //Socket 2
#define W5100_S3_DHAR COMMON_BASE+0x0706 //Socket 3
//Socket destination IP address register, R/W, default=0x00
#define W5100_S0_DIPR COMMON_BASE+0x040c //Socket 0
#define W5100_S1_DIPR COMMON_BASE+0x050c //Socket 1
#define W5100_S2_DIPR COMMON_BASE+0x060c //Socket 2
#define W5100_S3_DIPR COMMON_BASE+0x070c //Socket 3
//Socket destionation port register, R/W, default=0x00
#define W5100_S0_DPORT COMMON_BASE+0x0410 //Socket 0
#define W5100_S1_DPORT COMMON_BASE+0x0510 //Socket 1
#define W5100_S2_DPORT COMMON_BASE+0x0610 //Socket 2
#define W5100_S3_DPORT COMMON_BASE+0x0710 //Socket 3
//Socket maximum segment size register, R/W, default=0x00
#define W5100_S0_MSS COMMON_BASE+0x0412 //Socket 0
#define W5100_S1_MSS COMMON_BASE+0x0512 //Socket 1
#define W5100_S2_MSS COMMON_BASE+0x0612 //Socket 2
#define W5100_S3_MSS COMMON_BASE+0x0712 //Socket 3
//Socket IP protocol register, R/W, default=0x00
//See http://www.iana.org/assignments/protocol-number
#define W5100_S0_PROTO COMMON_BASE+0x0414 //Socket 0
#define W5100_S1_PROTO COMMON_BASE+0x0514 //Socket 1
#define W5100_S2_PROTO COMMON_BASE+0x0614 //Socket 2
#define W5100_S3_PROTO COMMON_BASE+0x0714 //Socket 3
//Socket IP type of servce register, R/W, default=0x00
#define W5100_S0_TOS COMMON_BASE+0x0415 //Socket 0
#define W5100_S1_TOS COMMON_BASE+0x0515 //Socket 1
#define W5100_S2_TOS COMMON_BASE+0x0615 //Socket 2
#define W5100_S3_TOS COMMON_BASE+0x0715 //Socket 3
//Socket IP time to live register, R/W, default=0x80
#define W5100_S0_TTL COMMON_BASE+0x0416 //Socket 0
#define W5100_S1_TTL COMMON_BASE+0x0516 //Socket 1
#define W5100_S2_TTL COMMON_BASE+0x0616 //Socket 2
#define W5100_S3_TTL COMMON_BASE+0x0716 //Socket 3
//Socket TX free size register, RO, default=0x0800
//should read upper byte first and lower byte later
#define W5100_S0_TX_FSR COMMON_BASE+0x0420 //Socket 0
#define W5100_S1_TX_FSR COMMON_BASE+0x0520 //Socket 1
#define W5100_S2_TX_FSR COMMON_BASE+0x0620 //Socket 2
#define W5100_S3_TX_FSR COMMON_BASE+0x0720 //Socket 3
//Socket TX read pointer register, RO, default=0x0000
//should read upper byte first and lower byte later
#define W5100_S0_TX_RR COMMON_BASE+0x0422 //Socket 0
#define W5100_S1_TX_RR COMMON_BASE+0x0522 //Socket 1
#define W5100_S2_TX_RR COMMON_BASE+0x0622 //Socket 2
#define W5100_S3_TX_RR COMMON_BASE+0x0722 //Socket 3
//Socket TX write pointer register, R/W, default=0x0000
//should read upper byte first and lower byte later
#define W5100_S0_TX_WR COMMON_BASE+0x0424 //Socket 0
#define W5100_S1_TX_WR COMMON_BASE+0x0524 //Socket 1
#define W5100_S2_TX_WR COMMON_BASE+0x0624 //Socket 2
#define W5100_S3_TX_WR COMMON_BASE+0x0724 //Socket 3
//Socket RX size register, RO, default=0x0000
//should read upper byte first and lower byte later
#define W5100_S0_RX_RSR COMMON_BASE+0x0426 //Socket 0
#define W5100_S1_RX_RSR COMMON_BASE+0x0526 //Socket 1
#define W5100_S2_RX_RSR COMMON_BASE+0x0626 //Socket 2
#define W5100_S3_RX_RSR COMMON_BASE+0x0726 //Socket 3
//Socket RX read pointer register, R/W, default=0x0000
//should read upper byte first and lower byte later
#define W5100_S0_RX_RR COMMON_BASE+0x0428 //Socket 0
#define W5100_S1_RX_RR COMMON_BASE+0x0528 //Socket 1
#define W5100_S2_RX_RR COMMON_BASE+0x0628 //Socket 2
#define W5100_S3_RX_RR COMMON_BASE+0x0728 //Socket 3
//Socket RX read pointer register, R/W, default=0x0000
//should read upper byte first and lower byte later
#define W5100_S0_RX_WR COMMON_BASE+0x042A //Socket 0
#define W5100_S1_RX_WR COMMON_BASE+0x052A //Socket 1
#define W5100_S2_RX_WR COMMON_BASE+0x062A //Socket 2
#define W5100_S3_RX_WR COMMON_BASE+0x072A //Socket 3
//TX memory
#define W5100_TX COMMON_BASE+0x4000
//RX memory
#define W5100_RX COMMON_BASE+0x6000
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -