.include Hardware.inc;
.include key.inc;
.include resource.inc;
.external _g_uisum;
                     
.DATA
    C_Address: .DW 0x3f00,0x8600,0xdb00,0xcf00, 0xe600,0xed00,0xfd00,0x8700,0xff00,0xef00;//'0''1''2''3''4''5''6''7''8''9'的代碼
    C_Dig:     .DW 0x0008,0x0020,0x0040,0x0080;//選中LED管
.CODE

//*********************************************************//
//函數:System_Initial()
//描述:鍵盤掃描初始化
//參數:無
//返回:無
//*********************************************************//
.CODE
.public _System_Initial;
.public	F_System_Initial;
_System_Initial: .PROC
F_System_Initial:
  		
		call	F_User_Init;				// 調用鍵盤掃描
		call	F_Key_Scan_Initial;				
		retf;
	   .ENDP;
//*********I/O初始化*****************************//
//*********************************************************//
F_User_Init: 
		R1 = 0xFFF8;
        [P_IOA_Dir] = R1;                    //A口為輸入口
        [P_IOA_Attrib] = R1;
        R1 = 0xF338			 
        [P_IOA_Data] = R1;                   //下拉輸入                     
        
        R1 = 0xFFEF;
        [P_IOB_Dir] = R1;                    //A口為輸入口
        R1=0xFFFB
        [P_IOB_Attrib] = R1;        			 
        [P_IOB_Data] = R1;                   //下拉輸入 
	      
		R1=0x0004 
		[P_FeedBack]=r1	       
        retf; 
    	 

//*********************************************************//
//函數:System_ServiceLoop()
//描述:鍵盤去抖和鍵盤掃描
//參數:無
//返回:無
//*********************************************************//
.public _System_ServiceLoop;
_System_ServiceLoop: .PROC                  

		call	F_Key_DebounceCnt_Down;		//鍵盤去抖
		call    F_Key_Scan_ServiceLoop;		//鍵盤掃描		
		R1=0x0001;                      	// 
		[P_Watchdog_Clear]=R1;       		//
        retf;
        .ENDP;
//*********************************************************//
//函數:Clear_WatchDog()
//描述:看門狗清0
//參數:無
//返回:無
//*********************************************************//
.public _Clear_WatchDog;
_Clear_WatchDog: 	.PROC
		R1=0x0001;                      	
		[P_Watchdog_Clear]=R1;       		
		retf;
		.ENDP
        
    


//=========================================//
//函數名稱：中斷設置
//========================================//

.public _RunTime2Hz; 
_RunTime2Hz:   .proc
	irq off
	r1 = 0x0004;
    [P_INT_Ctrl] = r1; 
    INT IRQ;           //開中斷
    retf
.endp;


.public _SP_INT_32Hz
_SP_INT_32Hz:	.proc

     irq off
     R1 = 0x0002;
     [P_TimeBase_Setup]=r1
    //r1 = [P_INT_Ctrl]
     r1 = 0x0002 						//開中斷IRQ6_TMB1和IRQ6_TMB2
	 [P_INT_Ctrl]= r1 
	 irq on
     retf;
     .endp;
      
.public _Turnoff_INT_32Hz
 _Turnoff_INT_32Hz: .proc
    irq off
    r1 = [P_INT_Ctrl]
	r1 &= 0xfffd;
	[P_INT_Ctrl] = r1;
    irq on
    retf;  
    .endp;  
     
.public _OffTime2Hz
_OffTime2Hz: .proc
   r1 = [P_INT_Ctrl]
   r1 &= 0xfffb;
   [P_INT_Ctrl] = r1;
   r1 = 0x0000
   [_g_uisum] = r1;
   retf;
 .endp;
 
//***************R/C/L通道選擇及二極管點亮******************// 
 .PUBLIC _Rline_on
_Rline_on: .PROC
	 R1=[P_IOA_Data]
	//選擇通道y0，亮紅燈
	 R1&=0xFFE7
	 R1|=0x4000
	 [P_IOA_Data]=r1	 
	 retf;
	 .ENDP
	 
.PUBLIC _Cline_on
_Cline_on: .PROC
	  R1=[P_IOA_Data]
	//選擇通道y1，亮綠黃燈
	 R1&=0xFFEF
	 R1|=0x2000
	 [P_IOA_Data]=r1	 
	 retf;
	 .ENDP
	 
	 
.PUBLIC _Lline_on
_Lline_on: .PROC
	 R1=[P_IOA_Data]
	//選擇通道y2，亮綠燈
	 R1&=0xFFF7
	 R1|=0x1000
	 [P_IOA_Data]=r1
 	 retf;
	 .ENDP
//************************************************//
	 
//***************R/C換檔***************************//
	 
.PUBLIC _R_Above1K
_R_Above1K:	.PROC
	 R1=[P_IOA_Data]
	//IOA5=0,IOA8=0,IOA6=1,IOA7=1
	 R1&=0xFEDF
	 R1|=0x40C0
	 [P_IOA_Data]=r1	 
	 retf;
	 .ENDP	 
	 
	 
.PUBLIC _C_Below1K
_C_Below1K:	.PROC
	  R1=[P_IOA_Data]
	//IOA9=0,IOA10=1
	 R1&=0xFDFF
	 R1|=0x0400
	 [P_IOA_Data]=r1
	 retf;
	 .ENDP
//***********************************************//	


.PUBLIC _TmbCount
_TmbCount:	.PROC
	 R1=0x0000
	 [P_TimerB_Data]=R1;//開始計數	
	 r1 =0x0007   //設置外部時鐘源
	 [P_TimerB_Ctrl]=r1
	 retf;   
	 .ENDP
	 
.PUBLIC _F_Show;
_F_Show: .PROC
	
    PUSH BP TO  [SP];  		      //彈出入口參數共兩個入口參數
    BP = SP + 1     
    R1 = [BP+3]                   //取出第一個入口參數
    R3 = [BP+4]                   //取出第二個入口參數
    R2 =  R1 + C_Dig;             //取LED管的片選地址    
    R2  = [R2]   
    R4 =  R3 + C_Address          //取顯示數據的地址 
    R4 = [R4] 
    R2 |= R4 
    r1=[P_IOB_Buffer]
    r1 &= 0x0017;
    r2 |= r1;    
    [P_IOB_Data] = R2;            //     
    POP BP FROM [SP]
    RETF;
.ENDP