/******************************************************************************
Filename:     hal.h
Target:       cc2430
Revised:      16/12-2005
Revision:     1.0

Description:
Hardware Abstraction Layer - Utility Library for CC2430, CC2431, CC1110 and CC2510.

******************************************************************************/

#ifndef HAL_H
#define HAL_H

#include "ioCC2430.h"




/******************************************************************************
*******************              Commonly used types        *******************
******************************************************************************/
typedef unsigned char       BOOL;

// Data
typedef unsigned char       BYTE;
typedef unsigned short      WORD;
typedef unsigned long       DWORD;

// Unsigned numbers
typedef unsigned char       UINT8;
typedef unsigned char       INT8U;
typedef unsigned short      UINT16;
typedef unsigned short       INT16U;
typedef unsigned long       UINT32;
typedef unsigned long       INT32U;
// Signed numbers
typedef signed char         INT8;
typedef signed short        INT16;
typedef signed long         INT32;

//-----------------------------------------------------------------------------
// Common values
#ifndef FALSE
   #define FALSE 0
#endif

#ifndef TRUE
   #define TRUE 1
#endif

#ifndef NULL
   #define NULL 0
#endif

#ifndef HIGH
   #define HIGH 1
#endif

#ifndef LOW
   #define LOW 0
#endif


#define		K_UP		0X20
#define		K_DOWN		0X21
#define		K_LIFT		0X22
#define		K_RIGHT		0X23
#define		K_CANCEL	0X24
#define		K_OK		0X25
//-----------------------------------------------------------------------------
extern INT8U LanguageSel;
#define UPPER_BYTE(a) ((BYTE) (((WORD)(a)) >> 8))
#define HIBYTE(a) UPPER_BYTE(a)

#define LOWER_BYTE(a) ((BYTE) ( (WORD)(a))      )
#define LOBYTE(a) LOWER_BYTE(a)

#define SET_WORD(regH, regL, word) \
   do{                             \
      (regH) = UPPER_BYTE((word)); \
      (regL) = LOWER_BYTE((word)); \
   }while(0)

#define READ_RFR16(reg) ((((WORD) ##reg##H) << 8) + ##reg##L)
#define WRITE_RFR16(reg, value) do { ##reg##H = HIBYTE(value); ##reg##L = LOBYTE(value); } while (0)





/******************************************************************************
*******************             Port functions/macros       *******************
******************************************************************************/

// Macros for simplifying access to I/O pin setup and usage

//*****************************************************************************


// Macros for configuring IO peripheral location:
// Example usage:
//   IO_PER_LOC_TIMER1_AT_PORT0_PIN234();
//   IO_PER_LOC_TIMER4_AT_PORT2_PIN03();
//   IO_PER_LOC_USART1_AT_PORT0_PIN2345();

#define IO_PER_LOC_TIMER1_AT_PORT0_PIN234() do { PERCFG = (PERCFG&~0x40)|0x00; } while (0)
#define IO_PER_LOC_TIMER1_AT_PORT1_PIN012() do { PERCFG = (PERCFG&~0x40)|0x40; } while (0)

#define IO_PER_LOC_TIMER3_AT_PORT1_PIN34()  do { PERCFG = (PERCFG&~0x20)|0x00; } while (0)
#define IO_PER_LOC_TIMER3_AT_PORT1_PIN67()  do { PERCFG = (PERCFG&~0x20)|0x20; } while (0)

#define IO_PER_LOC_TIMER4_AT_PORT1_PIN01()  do { PERCFG = (PERCFG&~0x10)|0x00; } while (0)
#define IO_PER_LOC_TIMER4_AT_PORT2_PIN03()  do { PERCFG = (PERCFG&~0x10)|0x10; } while (0)

#define IO_PER_LOC_SPI1_AT_PORT0_PIN2345()  do { PERCFG = (PERCFG&~0x08)|0x00; } while (0)
#define IO_PER_LOC_SPI1_AT_PORT1_PIN4567()  do { PERCFG = (PERCFG&~0x08)|0x08; } while (0)

#define IO_PER_LOC_SPI0_AT_PORT0_PIN2345()  do { PERCFG = (PERCFG&~0x04)|0x00; } while (0)
#define IO_PER_LOC_SPI0_AT_PORT1_PIN2345()  do { PERCFG = (PERCFG&~0x04)|0x04; } while (0)

#define IO_PER_LOC_UART1_AT_PORT0_PIN2345() do { PERCFG = (PERCFG&~0x02)|0x00; } while (0)
#define IO_PER_LOC_UART1_AT_PORT1_PIN4567() do { PERCFG = (PERCFG&~0x02)|0x02; } while (0)

#define IO_PER_LOC_UART0_AT_PORT0_PIN2345() do { PERCFG = (PERCFG&~0x01)|0x00; } while (0)
#define IO_PER_LOC_UART0_AT_PORT1_PIN2345() do { PERCFG = (PERCFG&~0x01)|0x01; } while (0)


// Actual MCU pin configuration:
//
// Peripheral I/O signal     Alt1       Alt2
// -------------------------------------------
// Timer1 channel0           P0.2       P1.2
// Timer1 channel1           P0.3       P1.1
// Timer1 channel2           P0.4       P1.0
// Timer3 channel0           P1.3       P1.6
// Timer3 channel1           P1.4       P1.7
// Timer4 channel0           P1.0       P2.0
// Timer4 channel1           P1.1       P2.3
// USART0 TXD/MOSI           P0.3       P1.5
// USART0 RXD/MISO           P0.2       P1.4
// USART0 RTS/SCK            P0.5       P1.3
// USART0 CTS/SS_N           P0.4       P1.2
// USART1 TXD/MOSI           P0.4       P1.6
// USART1 RXD/MISO           P0.5       P1.7
// USART1 RTS/SCK            P0.3       P1.5
// USART1 CTS/SS_N           P0.2       P1.4

// Macros for configuring IO direction:
// Example usage:
//   IO_DIR_PORT_PIN(0, 3, IO_IN);    // Set P0_3 to input
//   IO_DIR_PORT_PIN(2, 1, IO_OUT);   // Set P2_1 to output

#define IO_DIR_PORT_PIN(port, pin, dir)  \
   do {                                  \
      if (dir == IO_OUT)                 \
         P##port##DIR |= (0x01<<(pin));  \
      else                               \
         P##port##DIR &= ~(0x01<<(pin)); \
   }while(0)

// Where port={0,1,2}, pin={0,..,7} and dir is one of:
#define IO_IN   0
#define IO_OUT  1

// Macros for configuring IO input mode:
// Example usage:
//   IO_IMODE_PORT_PIN(0,0,IO_IMODE_PUD);
//   IO_IMODE_PORT_PIN(2,0,IO_IMODE_TRI);
//   IO_IMODE_PORT_PIN(1,3,IO_IMODE_PUD);

#define IO_IMODE_PORT_PIN(port, pin, imode) \
   do {                                     \
      if (imode == IO_IMODE_TRI)            \
         P##port##INP |= (0x01<<(pin));     \
      else                                  \
         P##port##INP &= ~(0x01<<(pin));    \
   } while (0)

// where imode is one of:
#define IO_IMODE_PUD  0 // Pull-up/pull-down
#define IO_IMODE_TRI  1 // Tristate

// Macro for configuring IO drive mode:
// Example usage:
//   IIO_PUD_PORT(0, IO_PULLUP);
//   IIO_PUD_PORT(1, IO_PULLDOWN);
//   IIO_PUD_PORT(2, IO_PULLUP);

#define IO_PUD_PORT(port, pud)        \
   do {                               \
      if (pud == IO_PULLDOWN)         \
         P2INP |= (0x01 << (port+5)); \
      else                            \
         P2INP &= ~(0x01 << (port+5));\
   } while (0)

#define IO_PULLUP          0
#define IO_PULLDOWN        1

// Macros for function select (General purpose I/O / Peripheral function):
// Example usage:
//   IO_FUNC_PORT0_PIN0(0, 0, IO_FUNC_PERIPH);
//   IO_FUNC_PORT0_PIN1(0, 1, IO_FUNC_GIO);
//   IO_FUNC_PORT2_PIN3(2, 3, IO_FUNC_PERIPH);

#define IO_FUNC_PORT_PIN(port, pin, func)  \
   do {                                    \
      if((port == 2) && (pin == 3)){       \
         if (func) {                       \
            P2SEL |= 0x02;                 \
         } else {                          \
            P2SEL &= ~0x02;                \
         }                                 \
      }                                    \
      else if((port == 2) && (pin == 4)){  \
         if (func) {                       \
            P2SEL |= 0x04;                 \
         } else {                          \
            P2SEL &= ~0x04;                \
         }                                 \
      }                                    \
      else{                                \
         if (func) {                       \
            P##port##SEL |= (0x01<<(pin)); \
         } else {                          \
            P##port##SEL &= ~(0x01<<(pin));\
        }                                  \
      }                                    \
   } while (0)

// where func is one of:
#define IO_FUNC_GIO     0 // General purpose I/O
#define IO_FUNC_PERIPH  1 // Peripheral function

// Macros for configuring the ADC input:
// Example usage:
//   IO_ADC_PORT0_PIN(0, IO_ADC_EN);
//   IO_ADC_PORT0_PIN(4, IO_ADC_DIS);
//   IO_ADC_PORT0_PIN(6, IO_ADC_EN);

#define IO_ADC_PORT0_PIN(pin, adcEn) \
   do {                              \
      if (adcEn)                     \
         ADCCFG |= (0x01<<pin);      \
      else                           \
         ADCCFG &= ~(0x01<<pin); }   \
   while (0)

// where adcEn is one of:
#define IO_ADC_EN           1 // ADC input enabled
#define IO_ADC_DIS          0 // ADC input disab

/******************************************************************************
*******************       Interrupt functions/macros        *******************
******************************************************************************/

// Macros which simplify access to interrupt enables, interrupt flags and
// interrupt priorities. Increases code legibility.

//******************************************************************************

#define INT_ON   1
#define INT_OFF  0
#define INT_SET  1
#define INT_CLR  0

// Global interrupt enables
#define INT_GLOBAL_ENABLE(on) EA=(!!on)

#define DISABLE_ALL_INTERRUPTS() (IEN0 = IEN1 = IEN2 = 0x00)

#define INUM_RFERR 0
#define INUM_ADC   1
#define INUM_URX0  2
#define INUM_URX1  3
#define INUM_ENC   4
#define INUM_ST    5
#define INUM_P2INT 6
#define INUM_UTX0  7
#define INUM_DMA   8
#define INUM_T1    9
#define INUM_T2    10
#define INUM_T3    11
#define INUM_T4    12
#define INUM_P0INT 13
#define INUM_UTX1  14
#define INUM_P1INT 15
#define INUM_RF    16
#define INUM_WDT   17

#define NBR_OF_INTERRUPTS 18

// Macro used together with the INUM_* constants
// to enable or disable certain interrupts.
// Example usage:
//   INT_ENABLE(INUM_RFERR, INT_ON);
//   INT_ENABLE(INUM_URX0, INT_OFF);
//   INT_ENABLE(INUM_T1, INT_ON);
//   INT_ENABLE(INUM_T2, INT_OFF);
#define INT_ENABLE(inum, on)                        \
   do {                                             \
      if      (inum==INUM_RFERR) { RFERRIE = on; }  \
      else if (inum==INUM_ADC)   { ADCIE   = on; }  \
      else if (inum==INUM_URX0)  { URX0IE  = on; }  \
      else if (inum==INUM_URX1)  { URX1IE  = on; }  \
      else if (inum==INUM_ENC)   { ENCIE   = on; }  \
      else if (inum==INUM_ST)    { STIE    = on; }  \
      else if (inum==INUM_P2INT) { (on) ? (IEN2 |= 0x02) : (IEN2 &= ~0x02); } \
      else if (inum==INUM_UTX0)  { (on) ? (IEN2 |= 0x04) : (IEN2 &= ~0x04); } \
      else if (inum==INUM_DMA)   { DMAIE   = on; }  \
      else if (inum==INUM_T1)    { T1IE    = on; }  \
      else if (inum==INUM_T2)    { T2IE    = on; }  \
      else if (inum==INUM_T3)    { T3IE    = on; }  \
      else if (inum==INUM_T4)    { T4IE    = on; }  \
      else if (inum==INUM_P0INT) { P0IE    = on; }  \
      else if (inum==INUM_UTX1)  { (on) ? (IEN2 |= 0x08) : (IEN2 &= ~0x08); } \
      else if (inum==INUM_P1INT) { (on) ? (IEN2 |= 0x10) : (IEN2 &= ~0x10); } \
      else if (inum==INUM_RF)    { (on) ? (IEN2 |= 0x01) : (IEN2 &= ~0x01); } \
      else if (inum==INUM_WDT)   { (on) ? (IEN2 |= 0x20) : (IEN2 &= ~0x20); } \
   } while (0)



// Macro for setting interrupt group priority