/* * (C) Copyright 2005 * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */#include <common.h>#include <asm/processor.h>#include <command.h>#include <malloc.h>DECLARE_GLOBAL_DATA_PTR;int board_early_init_f (void){	unsigned long cntrl0Reg;	/*	 * Setup GPIO pins	 */	cntrl0Reg = mfdcr(cntrl0);	mtdcr(cntrl0, cntrl0Reg | ((CFG_EEPROM_WP | CFG_PB_LED | CFG_SELF_RST | CFG_INTA_FAKE) << 5));	/* set output pins to high */	out32(GPIO0_OR,  CFG_EEPROM_WP);	/* setup for output (LED=off) */	out32(GPIO0_TCR, CFG_EEPROM_WP | CFG_PB_LED);	/*	 * IRQ 0-15  405GP internally generated; active high; level sensitive	 * IRQ 16    405GP internally generated; active low; level sensitive	 * IRQ 17-24 RESERVED	 * IRQ 25 (EXT IRQ 0) PB0; active low; level sensitive	 * IRQ 26 (EXT IRQ 1) PB1; active low; level sensitive	 * IRQ 27 (EXT IRQ 2) PCI SLOT 0; active low; level sensitive	 * IRQ 28 (EXT IRQ 3) PCI SLOT 1; active low; level sensitive	 * IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive	 * IRQ 30 (EXT IRQ 5) PCI SLOT 3; active low; level sensitive	 * IRQ 31 (EXT IRQ 6) unused	 */	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */	mtdcr(uicer, 0x00000000);	/* disable all ints */	mtdcr(uiccr, 0x00000000);	/* set all to be non-critical*/	mtdcr(uicpr, 0xFFFFFF81);	/* set int polarities */	mtdcr(uictr, 0x10000000);	/* set int trigger levels */	mtdcr(uicvcr, 0x00000001);	/* set vect base=0,INT0 highest priority*/	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */	return 0;}int misc_init_f (void){	return 0;  /* dummy implementation */}int misc_init_r (void){	unsigned long cntrl0Reg;	/* adjust flash start and offset */	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;	gd->bd->bi_flashoffset = 0;	/*	 * Select cts (and not dsr) on uart1	 */	cntrl0Reg = mfdcr(cntrl0);	mtdcr(cntrl0, cntrl0Reg | 0x00001000);	return (0);}/* * Check Board Identity: */int checkboard (void){	char str[64];	int i = getenv_r ("serial#", str, sizeof(str));	puts ("Board: ");	if (i == -1) {		puts ("### No HW ID - assuming CPCI2DP");	} else {		puts(str);	}	printf(" (Ver 1.0)");	putc ('\n');	return 0;}/* ------------------------------------------------------------------------- */long int initdram (int board_type){	unsigned long val;	mtdcr(memcfga, mem_mb0cf);	val = mfdcr(memcfgd);	return (4*1024*1024 << ((val & 0x000e0000) >> 17));}/* ------------------------------------------------------------------------- */#if defined(CFG_EEPROM_WREN)/* Input: <dev_addr>  I2C address of EEPROM device to enable. *	   <state>     -1: deliver current state *		       0: disable write *		       1: enable write *  Returns:	       -1: wrong device address *			0: dis-/en- able done *		     0/1: current state if <state> was -1. */int eeprom_write_enable (unsigned dev_addr, int state) {	if (CFG_I2C_EEPROM_ADDR != dev_addr) {		return -1;	} else {		switch (state) {		case 1:			/* Enable write access, clear bit GPIO_SINT2. */			out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP);			state = 0;			break;		case 0:			/* Disable write access, set bit GPIO_SINT2. */			out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);			state = 0;			break;		default:			/* Read current status back. */			state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP));			break;		}	}	return state;}#endif#if defined(CFG_EEPROM_WREN)int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]){	int query = argc == 1;	int state = 0;	if (query) {		/* Query write access state. */		state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1);		if (state < 0) {			puts ("Query of write access state failed.\n");		} else {			printf ("Write access for device 0x%0x is %sabled.\n",				CFG_I2C_EEPROM_ADDR, state ? "en" : "dis");			state = 0;		}	} else {		if ('0' == argv[1][0]) {			/* Disable write access. */			state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0);		} else {			/* Enable write access. */			state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1);		}		if (state < 0) {			puts ("Setup of write access state failed.\n");		}	}	return state;}U_BOOT_CMD(	eepwren,	2,	0,	do_eep_wren,	"eepwren - Enable / disable / query EEPROM write access\n",	NULL	);#endif /* #if defined(CFG_EEPROM_WREN) */