?? reg2440.a
字號:
;******************************************************************************
;*
;* System On Chip(SOC)
;*
;* Copyright (c) 2002 Software Center, Samsung Electronics, Inc.
;* All rights reserved.
;*
;* This software is the confidential and proprietary information of Samsung
;* Electronics, Inc("Confidential Information"). You Shall not disclose such
;* Confidential Information and shall use it only in accordance with the terms
;* of the license agreement you entered into Samsung.
;*
;*-----------------------------------------------------------------------------
;*
;* S3C2440 BSP
;*
;* 2440.a : S3C2440's Register map (non-translated by MMU) &
;* Memory Configuration Table
;*
;* @author zartoven@samsung.com (SOC, SWC, SAMSUNG Electronics)
;*
;* @date 2002/04/04
;*
;* Log:
;* 2002/04/04 Start
;*
;******************************************************************************
;******************************************************************************
; Memory control
;******************************************************************************
BWSCON EQU 0x48000000 ;Bus width & wait status
BANKCON0 EQU 0x48000004 ;Boot ROM control
BANKCON1 EQU 0x48000008 ;BANK1 control
BANKCON2 EQU 0x4800000c ;BANK2 cControl
BANKCON3 EQU 0x48000010 ;BANK3 control
BANKCON4 EQU 0x48000014 ;BANK4 control
BANKCON5 EQU 0x48000018 ;BANK5 control
BANKCON6 EQU 0x4800001c ;BANK6 control
BANKCON7 EQU 0x48000020 ;BANK7 control
REFRESH EQU 0x48000024 ;DRAM/SDRAM refresh
BANKSIZE EQU 0x48000028 ;Flexible Bank Size
MRSRB6 EQU 0x4800002c ;Mode register set for SDRAM
MRSRB7 EQU 0x48000030 ;Mode register set for SDRAM
vREFRESH EQU 0xB0800024 ;DRAM/SDRAM refresh
;******************************************************************************
; INTERRUPT
;******************************************************************************
SRCPND EQU 0x4a000000 ;Interrupt request status
INTMOD EQU 0x4a000004 ;Interrupt mode control
INTMSK EQU 0x4a000008 ;Interrupt mask control
PRIORITY EQU 0x4a00000c ;IRQ priority control
INTPND EQU 0x4a000010 ;Interrupt request status
INTOFFSET EQU 0x4a000014 ;Interruot request source offset
SUSSRCPND EQU 0x4a000018 ;Sub source pending
INTSUBMSK EQU 0x4a00001c ;Interrupt sub mask
vSRCPND EQU 0xb0a00000 ;Interrupt request status
vINTMOD EQU 0xb0a00004 ;Interrupt mode control
vINTMSK EQU 0xb0a00008 ;Interrupt mask control
vPRIORITY EQU 0xb0a0000c ;IRQ priority control
vINTPND EQU 0xb0a00010 ;Interrupt request status
vINTOFFSET EQU 0xb0a00014 ;Interruot request source offset
vSUSSRCPND EQU 0xb0a00018 ;Sub source pending
vINTSUBMSK EQU 0xb0a0001c ;Interrupt sub mask
vINTBASE EQU 0xb0a00000 ;Interrupt request status
oSRCPND EQU 0x00 ;Interrupt request status
oINTMSK EQU 0x08 ;Interrupt mask control
oINTPND EQU 0x10 ;Interrupt request status
oINTSUBMSK EQU 0x1c ;Interrupt sub mask
;******************************************************************************
; DMA
;******************************************************************************
DISRC0 EQU 0x4b000000 ;DMA 0 Initial source
DISRCC0 EQU 0x4b000004 ;DMA 0 Initial source control
DIDST0 EQU 0x4b000008 ;DMA 0 Initial Destination
DIDSTC0 EQU 0x4b00000c ;DMA 0 Initial Destination control
DCON0 EQU 0x4b000010 ;DMA 0 Control
DSTAT0 EQU 0x4b000014 ;DMA 0 Status
DCSRC0 EQU 0x4b000018 ;DMA 0 Current source
DCDST0 EQU 0x4b00001c ;DMA 0 Current destination
DMASKTRIG0 EQU 0x4b000020 ;DMA 0 Mask trigger
DISRC1 EQU 0x4b000040 ;DMA 1 Initial source
DISRCC1 EQU 0x4b000044 ;DMA 1 Initial source control
DIDST1 EQU 0x4b000048 ;DMA 1 Initial Destination
DIDSTC1 EQU 0x4b00004c ;DMA 1 Initial Destination control
DCON1 EQU 0x4b000050 ;DMA 1 Control
DSTAT1 EQU 0x4b000054 ;DMA 1 Status
DCSRC1 EQU 0x4b000058 ;DMA 1 Current source
DCDST1 EQU 0x4b00005c ;DMA 1 Current destination
DMASKTRIG1 EQU 0x4b000060 ;DMA 1 Mask trigger
DISRC2 EQU 0x4b000080 ;DMA 2 Initial source
DISRCC2 EQU 0x4b000084 ;DMA 2 Initial source control
DIDST2 EQU 0x4b000088 ;DMA 2 Initial Destination
DIDSTC2 EQU 0x4b00008c ;DMA 2 Initial Destination control
DCON2 EQU 0x4b000090 ;DMA 2 Control
DSTAT2 EQU 0x4b000094 ;DMA 2 Status
DCSRC2 EQU 0x4b000098 ;DMA 2 Current source
DCDST2 EQU 0x4b00009c ;DMA 2 Current destination
DMASKTRIG2 EQU 0x4b0000a0 ;DMA 2 Mask trigger
DISRC3 EQU 0x4b0000c0 ;DMA 3 Initial source
DISRCC3 EQU 0x4b0000c4 ;DMA 3 Initial source control
DIDST3 EQU 0x4b0000c8 ;DMA 3 Initial Destination
DIDSTC3 EQU 0x4b0000cc ;DMA 3 Initial Destination control
DCON3 EQU 0x4b0000d0 ;DMA 3 Control
DSTAT3 EQU 0x4b0000d4 ;DMA 3 Status
DCSRC3 EQU 0x4b0000d8 ;DMA 3 Current source
DCDST3 EQU 0x4b0000dc ;DMA 3 Current destination
DMASKTRIG3 EQU 0x4b0000e0 ;DMA 3 Mask trigger
;******************************************************************************=========
; CLOCK & POWER MANAGEMENT
;******************************************************************************=========
LOCKTIME EQU 0x4c000000 ;PLL lock time counter
MPLLCON EQU 0x4c000004 ;MPLL Control
UPLLCON EQU 0x4c000008 ;UPLL Control
CLKCON EQU 0x4c00000c ;Clock generator control
CLKSLOW EQU 0x4c000010 ;Slow clock control
CLKDIVN EQU 0x4c000014 ;Clock divider control
CAMDIVN EQU 0x4c000018
vMPLLCON EQU 0xb0c00004 ;MPLL Control
vCLKCON EQU 0xb0c0000c ;Clock generator control
vCLKDIVN EQU 0xb0c00014 ;Clock divider control
vCAMDIVN EQU 0xb0c00018 ;Camera Clock divider control
;******************************************************************************
; LCD CONTROLLER
;******************************************************************************
LCDCON1 EQU 0x4d000000 ;LCD control 1
LCDCON2 EQU 0x4d000004 ;LCD control 2
LCDCON3 EQU 0x4d000008 ;LCD control 3
LCDCON4 EQU 0x4d00000c ;LCD control 4
LCDCON5 EQU 0x4d000010 ;LCD control 5
LCDSADDR1 EQU 0x4d000014 ;STN/TFT Frame buffer start address 1
LCDSADDR2 EQU 0x4d000018 ;STN/TFT Frame buffer start address 2
LCDSADDR3 EQU 0x4d00001c ;STN/TFT Virtual screen address set
REDLUT EQU 0x4d000020 ;STN Red lookup table
GREENLUT EQU 0x4d000024 ;STN Green lookup table
BLUELUT EQU 0x4d000028 ;STN Blue lookup table
DITHMODE EQU 0x4d00004c ;STN Dithering mode
TPAL EQU 0x4d000050 ;TFT Temporary palette
LCDINTPND EQU 0x4d000054 ;LCD Interrupt pending
LCDSRCPND EQU 0x4d000058 ;LCD Interrupt source
LCDINTMSK EQU 0x4d00005c ;LCD Interrupt mask
;LPCSEL EQU 0x4d000060 ;LPC3600 Control
TCONSEL EQU 0x4d000060 ;LPC3600 Control ;;; SHL
;vLCDCON1 EQU 0x90d00000 ;LCD control 1
;******************************************************************************
; NAND flash
;******************************************************************************
NFCONF EQU 0x4e000000 ;NAND Flash configuration
NFCMD EQU 0x4e000004 ;NADD Flash command
NFADDR EQU 0x4e000008 ;NAND Flash address
NFDATA EQU 0x4e00000c ;NAND Flash data
NFSTAT EQU 0x4e000010 ;NAND Flash operation status
NFECC EQU 0x4e000014 ;NAND Flash ECC
;******************************************************************************
; UART
;******************************************************************************
ULCON0 EQU 0x50000000 ;UART 0 Line control
UCON0 EQU 0x50000004 ;UART 0 Control
UFCON0 EQU 0x50000008 ;UART 0 FIFO control
UMCON0 EQU 0x5000000c ;UART 0 Modem control
UTRSTAT0 EQU 0x50000010 ;UART 0 Tx/Rx status
UERSTAT0 EQU 0x50000014 ;UART 0 Rx error status
UFSTAT0 EQU 0x50000018 ;UART 0 FIFO status
UMSTAT0 EQU 0x5000001c ;UART 0 Modem status
UBRDIV0 EQU 0x50000028 ;UART 0 Baud rate divisor
ULCON1 EQU 0x50004000 ;UART 1 Line control
UCON1 EQU 0x50004004 ;UART 1 Control
UFCON1 EQU 0x50004008 ;UART 1 FIFO control
UMCON1 EQU 0x5000400c ;UART 1 Modem control
UTRSTAT1 EQU 0x50004010 ;UART 1 Tx/Rx status
UERSTAT1 EQU 0x50004014 ;UART 1 Rx error status
UFSTAT1 EQU 0x50004018 ;UART 1 FIFO status
UMSTAT1 EQU 0x5000401c ;UART 1 Modem status
UBRDIV1 EQU 0x50004028 ;UART 1 Baud rate divisor
ULCON2 EQU 0x50008000 ;UART 2 Line control
UCON2 EQU 0x50008004 ;UART 2 Control
UFCON2 EQU 0x50008008 ;UART 2 FIFO control
UMCON2 EQU 0x5000800c ;UART 2 Modem control
UTRSTAT2 EQU 0x50008010 ;UART 2 Tx/Rx status
UERSTAT2 EQU 0x50008014 ;UART 2 Rx error status
UFSTAT2 EQU 0x50008018 ;UART 2 FIFO status
UMSTAT2 EQU 0x5000801c ;UART 2 Modem status
UBRDIV2 EQU 0x50008028 ;UART 2 Baud rate divisor
UTXH0 EQU 0x50000020 ;UART 0 Transmission Hold
URXH0 EQU 0x50000024 ;UART 0 Receive buffer
UTXH1 EQU 0x50004020 ;UART 1 Transmission Hold
URXH1 EQU 0x50004024 ;UART 1 Receive buffer
UTXH2 EQU 0x50008020 ;UART 2 Transmission Hold
URXH2 EQU 0x50008024 ;UART 2 Receive buffer
;******************************************************************************
; PWM TIMER
;******************************************************************************
TCFG0 EQU 0x51000000 ;Timer 0 configuration
TCFG1 EQU 0x51000004 ;Timer 1 configuration
TCON EQU 0x51000008 ;Timer control
TCNTB0 EQU 0x5100000c ;Timer count buffer 0
TCMPB0 EQU 0x51000010 ;Timer compare buffer 0
TCNTO0 EQU 0x51000014 ;Timer count observation 0
TCNTB1 EQU 0x51000018 ;Timer count buffer 1
TCMPB1 EQU 0x5100001c ;Timer compare buffer 1
TCNTO1 EQU 0x51000020 ;Timer count observation 1
TCNTB2 EQU 0x51000024 ;Timer count buffer 2
TCMPB2 EQU 0x51000028 ;Timer compare buffer 2
TCNTO2 EQU 0x5100002c ;Timer count observation 2
TCNTB3 EQU 0x51000030 ;Timer count buffer 3
TCMPB3 EQU 0x51000034 ;Timer compare buffer 3
TCNTO3 EQU 0x51000038 ;Timer count observation 3
TCNTB4 EQU 0x5100003c ;Timer count buffer 4
TCNTO4 EQU 0x51000040 ;Timer count observation 4
;******************************************************************************
; USB DEVICE
;******************************************************************************
FUNC_ADDR_REG EQU 0x52000140 ;Function address
PWR_REG EQU 0x52000144 ;Power management
EP_INT_REG EQU 0x52000148 ;EP Interrupt pending and clear
USB_INT_REG EQU 0x52000158 ;USB Interrupt pending and clear
EP_INT_EN_REG EQU 0x5200015c ;Interrupt enable
USB_INT_EN_REG EQU 0x5200016c
FRAME_NUM1_REG EQU 0x52000170 ;Frame number lower byte
FRAME_NUM2_REG EQU 0x52000174 ;Frame number lower byte
INDEX_REG EQU 0x52000178 ;Register index
MAXP_REG EQU 0x52000180 ;Endpoint max packet
EP0_CSR EQU 0x52000184 ;Endpoint 0 status
IN_CSR1_REG EQU 0x52000184 ;In endpoint control status
IN_CSR2_REG EQU 0x52000188
OUT_CSR1_REG EQU 0x52000190 ;Out endpoint control status
OUT_CSR2_REG EQU 0x52000194
OUT_FIFO_CNT1_REG EQU 0x52000198 ;Endpoint out write count
OUT_FIFO_CNT2_REG EQU 0x5200019c
EP0_FIFO EQU 0x520001c0 ;Endpoint 0 FIFO
EP1_FIFO EQU 0x520001c4 ;Endpoint 1 FIFO
EP2_FIFO EQU 0x520001c8 ;Endpoint 2 FIFO
EP3_FIFO EQU 0x520001cc ;Endpoint 3 FIFO
EP4_FIFO EQU 0x520001d0 ;Endpoint 4 FIFO
EP1_DMA_CON EQU 0x52000200 ;EP1 DMA interface control
EP1_DMA_UNIT EQU 0x52000204 ;EP1 DMA Tx unit counter
EP1_DMA_FIFO EQU 0x52000208 ;EP1 DMA Tx FIFO counter
EP1_DMA_TTC_L EQU 0x5200020c ;EP1 DMA total Tx counter
EP1_DMA_TTC_M EQU 0x52000210
EP1_DMA_TTC_H EQU 0x52000214
EP2_DMA_CON EQU 0x52000218 ;EP2 DMA interface control
EP2_DMA_UNIT EQU 0x5200021c ;EP2 DMA Tx unit counter
EP2_DMA_FIFO EQU 0x52000220 ;EP2 DMA Tx FIFO counter
EP2_DMA_TTC_L EQU 0x52000224 ;EP2 DMA total Tx counter
EP2_DMA_TTC_M EQU 0x52000228
EP2_DMA_TTC_H EQU 0x5200022c
EP3_DMA_CON EQU 0x52000240 ;EP3 DMA interface control
EP3_DMA_UNIT EQU 0x52000244 ;EP3 DMA Tx unit counter
EP3_DMA_FIFO EQU 0x52000248 ;EP3 DMA Tx FIFO counter
EP3_DMA_TTC_L EQU 0x5200024c ;EP3 DMA total Tx counter
EP3_DMA_TTC_M EQU 0x52000250
EP3_DMA_TTC_H EQU 0x52000254
EP4_DMA_CON EQU 0x52000258 ;EP4 DMA interface control
EP4_DMA_UNIT EQU 0x5200025c ;EP4 DMA Tx unit counter
EP4_DMA_FIFO EQU 0x52000260 ;EP4 DMA Tx FIFO counter
EP4_DMA_TTC_L EQU 0x52000264 ;EP4 DMA total Tx counter
EP4_DMA_TTC_M EQU 0x52000268
EP4_DMA_TTC_H EQU 0x5200026c
;******************************************************************************
; WATCH DOG TIMER
;******************************************************************************
WTCON EQU 0x53000000 ;Watch-dog timer mode
WTDAT EQU 0x53000004 ;Watch-dog timer data
WTCNT EQU 0x53000008 ;Eatch-dog timer count
vWTCON EQU 0xB1300000 ;Watch-dog timer mode
vWTDAT EQU 0xB1300004 ;Watch-dog timer data
vWTCNT EQU 0xB1300008 ;Eatch-dog timer count
;******************************************************************************
; IIC
;******************************************************************************
IICCON EQU 0x54000000 ;IIC control
IICSTAT EQU 0x54000004 ;IIC status
IICADD EQU 0x54000008 ;IIC address
IICDS EQU 0x5400000c ;IIC data shift
;******************************************************************************
; IIS
;******************************************************************************
IISCON EQU 0x55000000 ;IIS Control
IISMOD EQU 0x55000004 ;IIS Mode
IISPSR EQU 0x55000008 ;IIS Prescaler
IISFCON EQU 0x5500000c ;IIS FIFO control
IISFIFO EQU 0x55000010 ;IIS FIFO entry
;******************************************************************************
; I/O PORT
;******************************************************************************
GPACON EQU 0x56000000 ;Port A control
GPADAT EQU 0x56000004 ;Port A data
GPBCON EQU 0x56000010 ;Port B control
GPBDAT EQU 0x56000014 ;Port B data
GPBUP EQU 0x56000018 ;Pull-up control B
GPCCON EQU 0x56000020 ;Port C control
GPCDAT EQU 0x56000024 ;Port C data
GPCUP EQU 0x56000028 ;Pull-up control C
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -