?? 2410lib.c
字號:
//===================================================================
// File Name : 2410lib.c
// Function : S3C2410 PLL,Uart, LED, Port Init
// Program : Shin, On Pil (SOP)
// Date : March 20, 2002
// Version : 0.0
// History
// 0.0 : Programming start (February 20,2002) -> SOP
//===================================================================
#include "def.h"
#include "option.h"
#include "2410addr.h"
#include "2410lib.h"
#include "2410slib.h"
#include "timer.h"
#include <stdarg.h>
#include <string.h>
#include <stdlib.h>
//#include <stdio.h>
#include <ctype.h>
extern char Image$$RW$$Limit[];
void *mallocPt=Image$$RW$$Limit;
//***************************[ SYSTEM ]***************************************************
static int delayLoopCount = 400;
void Delay(int time)
{
// time=0: adjust the Delay function by WatchDog timer.
// time>0: the number of loop time
// resolution of time is 100us.
int i,adjust=0;
if(time==0)
{
time = 200;
adjust = 1;
delayLoopCount = 400;
//PCLK/1M,Watch-dog disable,1/64,interrupt disable,reset disable
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3);
rWTDAT = 0xffff; //for first update
rWTCNT = 0xffff; //resolution=64us @any PCLK
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3)|(1<<5); //Watch-dog timer start
}
for(;time>0;time--)
for(i=0;i<delayLoopCount;i++);
if(adjust==1)
{
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3); //Watch-dog timer stop
i = 0xffff - rWTCNT; //1count->64us, 200*400 cycle runtime = 64*i us
delayLoopCount = 8000000/(i*64); //200*400:64*i=1*x:100 -> x=80000*100/(64*i)
}
}
//***************************[ PORTS ]****************************************************
void Port_Init(void)
{
//CAUTION:Follow the configuration order for setting the ports.
// 1) setting value(GPnDAT)
// 2) setting control register (GPnCON)
// 3) configure pull-up resistor(GPnUP)
//32bit data bus configuration
//*** PORT A GROUP
//Ports : GPA22 GPA21 GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12
//Signal : nFCE nRSTOUT nFRE nFWE ALE CLE nGCS5 nGCS4 nGCS3 nGCS2 nGCS1
//Binary : 1 0 1 , 1 1 1 1 , 1 1 1 1
//Ports : GPA11 GPA10 GPA9 GPA8 GPA7 GPA6 GPA5 GPA4 GPA3 GPA2 GPA1 GPA0
//Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0
//Binary : 1 1 1 1 , 1 1 1 1 , 1 1 1 0
rGPACON = 0x5ffffe;
//**** PORT B GROUP
//Ports : GPB10 GPB9 GPB8 GPB7 GPB6 GPB5 GPB4 GPB3 GPB2 GPB1 GPB0
//Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard
//Setting: INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
//Binary : 00 , 01 00 , 01 00 , 01 01 , 01 01 , 01 01
rGPBCON = 0x044555;
rGPBUP = 0x7ff; // The pull up function is disabled GPB[10:0]
//*** PORT C GROUP
//Ports : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8 GPC7 GPC6 GPC5 GPC4 GPC3 GPC2 GPC1 GPC0
//Signal : VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10
rGPCCON = 0xaaaaaaaa;
rGPCUP = 0xffff; // The pull up function is disabled GPC[15:0]
//*** PORT D GROUP
//Ports : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0
//Signal : VD23 VD22 VD21 VD20 VD19 VD18 VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9 VD8
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,10 10
rGPDCON = 0xaaaaaaaa;
rGPDUP = 0xffff; // The pull up function is disabled GPD[15:0]
//*** PORT E GROUP
//Ports : GPE15 GPE14 GPE13 GPE12 GPE11 GPE10 GPE9 GPE8 GPE7 GPE6 GPE5 GPE4
//Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,
//-------------------------------------------------------------------------------------------------------
//Ports : GPE3 GPE2 GPE1 GPE0
//Signal : I2SSDI CDCLK I2SSCLK I2SLRCK
//Binary : 10 10 , 10 10
rGPECON = 0x5aaaaaaa;
rGPEUP = 0xffff; // The pull up function is disabled GPE[15:0]
//*** PORT F GROUP
//Ports : GPF7 GPF6 GPF5 GPF4 GPF3 GPF2 GPF1 GPF0
//Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0
//Setting: Output Output Output Output EINT3 EINT2 EINT1 EINT0
//Binary : 01 01 , 01 01 , 10 10 , 10 10
rGPFCON = 0x55aa;
rGPFUP = 0xff; // The pull up function is disabled GPF[7:0]
//*** PORT G GROUP
//Ports : GPG15 GPG14 GPG13 GPG12 GPG11 GPG10 GPG9 GPG8 GPG7 GPG6
//Signal : nYPON YMON nXPON XMON EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI
//Setting: nYPON YMON nXPON XMON EINT19 Output Output Output SPICLK1 SPIMOSI1
//Binary : 11 11 , 11 11 , 10 01 , 01 01 , 11 11
//-----------------------------------------------------------------------------------------
//Ports : GPG5 GPG4 GPG3 GPG2 GPG1 GPG0
//Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA
//Setting: SPIMISO1 LCD_PWRDN EINT11 nSS0 EINT9 EINT8
//Binary : 11 11 , 10 11 , 10 10
rGPGCON = 0xff81ffba; //GPG10 input,GPG9 input
rGPGUP = 0xffff; // The pull up function is disabled GPG[15:0]
//*** PORT H GROUP
//Ports : GPH10 GPH9 GPH8 GPH7 GPH6 GPH5 GPH4 GPH3 GPH2 GPH1 GPH0
//Signal : CLKOUT1 CLKOUT0 UCLK nCTS1 nRTS1 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0
//Binary : 10 , 10 10 , 11 11 , 10 10 , 10 10 , 10 10
rGPHCON = 0xfaaa;//0x2afaaa;
rGPHUP = 0x7ff; // The pull up function is disabled GPH[10:0]
//External interrupt will be falling edge triggered.
rEXTINT0 = 0x22222222; // EINT[7:0]
rEXTINT1 = 0x22222222; // EINT[15:8]
rEXTINT2 = 0x22222222; // EINT[23:16]
}
//***************************[ UART ]******************************
extern U32 SYS_PCLK;
static int whichUart=0;
void Uart_Init(int pclk,int baud)
{
int i;
rGPHCON = rGPHCON & (~(0xffff)) ;
rGPHCON = rGPHCON | (0xaaa0) ;
rGPHUP = 0x0; // The pull up function is enable
if(pclk == 0) pclk = SYS_PCLK;
// pclk = PCLK;
rUFCON0 = 0x0; //UART channel 0 FIFO control register, FIFO disable
rUFCON1 = 0x0; //UART channel 1 FIFO control register, FIFO disable
rUFCON2 = 0x0; //UART channel 2 FIFO control register, FIFO disable
rUMCON0 = 0x0; //UART chaneel 0 MODEM control register, AFC disable
rUMCON1 = 0x0; //UART chaneel 1 MODEM control register, AFC disable
//UART0
rULCON0 = 0x3; //Line control register : Normal,No parity,1 stop,8 bits
// [10] [9] [8] [7] [6] [5] [4] [3:2] [1:0]
// Clock Sel, Tx Int, Rx Int, Rx Time Out, Rx err, Loop-back, Send break, Transmit Mode, Receive Mode
// 0 1 0 , 0 1 0 0 , 01 01
// PCLK Level Pulse Disable Generate Normal Normal Interrupt or Polling
rUCON0 = 0x245; // Control register
rUBRDIV0=( (int)(pclk/16./baud+0.5) -1 ); //Baud rate divisior register 0
//UART1
rULCON1 = 0x3;
rUCON1 = 0x245;
rUBRDIV1=( (int)(pclk/16./baud) -1 );
//UART2
rULCON2 = 0x3;
rUCON2 = 0x245;
rUBRDIV2=( (int)(pclk/16./baud) -1 );
for(i=0;i<100;i++);
}
//===================================================================
void Uart_Select(int ch)
{
whichUart = ch;
}
//*****************************************************************************
//在串口1和2之間切換
//*****************************************************************************
void Uart2_Test( void )
{
U8 m ;
U8 n = 0 ;
rGPHCON = rGPHCON & (~(0xffff)) ;
rGPHCON = rGPHCON | (0xaaa0) ;
rGPHUP = 0x0; // The pull up function is enable
SetClockDivider(1, 1);
SetSysFclk(DFT_FCLK_VAL);
Delay( 0 ) ;
Uart_Init(0, UART_BAUD);
Uart_Select(0);
Uart_Printf( "\nUART2 Test\n" ) ;
Uart_Printf( "\nPlease pull out COM cable and plug into the UART2 connector\n" ) ;
Uart_Select( 1 ) ;
while( (m=Uart_GetKey()) != ESC_KEY )
{
if( m != 0 )
{
puts( "'ESC' key return to UART1, The input of you is " ) ;
putch( m ) ; puts( "\n" ) ;
n = 1 ;
}
else
{
if( n==0 )
{
puts( "Now is UART2 output, do you see? Any key to display, 'ESC' key return to UART1 \n" ) ;
n = 0 ;
Delay( 6000 ) ;
}
}
}
Uart_Printf( "\nPlease pull out COM cable and plug into the UART1 connector\n" ) ;
Uart_Select( 0 ) ;
while( (m=Uart_GetKey()) != ESC_KEY )
{
Uart_Printf( "Please Enter 'ESC' key to Main menu \n" ) ;
Delay( 6000 ) ;
}
}
//===================================================================
void Uart_TxEmpty(int ch)
{
if(ch==0)
while(!(rUTRSTAT0 & 0x4)); //Wait until tx shifter is empty.
else if(ch==1)
while(!(rUTRSTAT1 & 0x4)); //Wait until tx shifter is empty.
else if(ch==2)
while(!(rUTRSTAT2 & 0x4)); //Wait until tx shifter is empty.
}
//=====================================================================
char getch(void)
{
if(whichUart==0)
{
while(!(rUTRSTAT0 & 0x1)); //Receive data ready
return RdURXH0();
}
else if(whichUart==1)
{
while(!(rUTRSTAT1 & 0x1)); //Receive data ready
return RdURXH1();
}
else if(whichUart==2)
{
while(!(rUTRSTAT2 & 0x1)); //Receive data ready
return RdURXH2();
}
return 0;
}
//====================================================================
char getkey(void)
{
if(whichUart==0)
{
if(rUTRSTAT0 & 0x1) //Receive data ready
return RdURXH0();
else
return 0;
}
else if(whichUart==1)
{
if(rUTRSTAT1 & 0x1) //Receive data ready
return RdURXH1();
else
return 0;
}
else if(whichUart==2)
{
if(rUTRSTAT2 & 0x1) //Receive data ready
return RdURXH2();
else
return 0;
}
return 0;
}
//====================================================================
void gets(char *string)
{
char *string2 = string;
char c;
while((c = getch())!='\r')
{
if(c=='\b')
{
if( (int)string2 < (int)string )
{
printf("\b \b");
string--;
}
}
else
{
*string++ = c;
putch(c);
}
}
*string='\0';
putch('\n');
}
//=====================================================================
int Uart_GetIntNum(void)
{
char str[30];
char *string = str;
int base = 10;
int minus = 0;
int result = 0;
int lastIndex;
int i;
gets(string);
if(string[0]=='-')
{
minus = 1;
string++;
}
if(string[0]=='0' && (string[1]=='x' || string[1]=='X'))
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -