/* * Definitions for the FTDI USB Single Port Serial Converter -  * known as FTDI_SIO (Serial Input/Output application of the chipset)  * * The example I have is known as the USC-1000 which is available from * http://www.dse.co.nz - cat no XH4214 It looks similar to this: * http://www.dansdata.com/usbser.htm but I can't be sure There are other * USC-1000s which don't look like my device though so beware! * * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,  * USB on the other. * * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details * of the protocol required to talk to the device and ongoing assistence * during development. * * Bill Ryder - bryder@sgi.com of Silicon Graphics, Inc.- wrote the  * FTDI_SIO implementation. * */#define FTDI_VID	0x0403	/* Vendor Id */#define FTDI_SIO_PID	0x8372	/* Product Id SIO application of 8U100AX  */#define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */#define FTDI_SIO_RESET 		0 /* Reset the port */#define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */#define FTDI_SIO_SET_FLOW_CTRL	2 /* Set flow control register */#define FTDI_SIO_SET_BAUD_RATE	3 /* Set baud rate */#define FTDI_SIO_SET_DATA	4 /* Set the data characteristics of the port */#define FTDI_SIO_GET_MODEM_STATUS	5 /* Retrieve current value of modern status register */#define FTDI_SIO_SET_EVENT_CHAR	6 /* Set the event character */#define FTDI_SIO_SET_ERROR_CHAR	7 /* Set the error character *//* Port Identifier Table */#define PIT_DEFAULT 		0 /* SIOA */#define PIT_SIOA		1 /* SIOA *//* The device this driver is tested with one has only one port */#define PIT_SIOB		2 /* SIOB */#define PIT_PARALLEL		3 /* Parallel *//* FTDI_SIO_RESET */#define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET#define FTDI_SIO_RESET_REQUEST_TYPE 0x40#define FTDI_SIO_RESET_SIO 0#define FTDI_SIO_RESET_PURGE_RX 1#define FTDI_SIO_RESET_PURGE_TX 2/* * BmRequestType:  0100 0000B * bRequest:       FTDI_SIO_RESET * wValue:         Control Value  *                   0 = Reset SIO *                   1 = Purge RX buffer *                   2 = Purge TX buffer * wIndex:         Port * wLength:        0 * Data:           None * * The Reset SIO command has this effect: * *    Sets flow control set to 'none' *    Event char = $0D *    Event trigger = disabled *    Purge RX buffer *    Purge TX buffer *    Clear DTR *    Clear RTS *    baud and data format not reset * * The Purge RX and TX buffer commands affect nothing except the buffers *   *//* FTDI_SIO_SET_BAUDRATE */#define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40#define FTDI_SIO_SET_BAUDRATE_REQUEST 3/* * BmRequestType:  0100 0000B * bRequest:       FTDI_SIO_SET_BAUDRATE * wValue:         BaudRate value - see below * wIndex:         Port * wLength:        0 * Data:           None */typedef enum {	sio = 1,	F8U232AM = 2,} ftdi_type_t;typedef enum { ftdi_sio_b300 = 0,  ftdi_sio_b600 = 1,  ftdi_sio_b1200 = 2, ftdi_sio_b2400 = 3, ftdi_sio_b4800 = 4, ftdi_sio_b9600 = 5, ftdi_sio_b19200 = 6, ftdi_sio_b38400 = 7, ftdi_sio_b57600 = 8, ftdi_sio_b115200 = 9} FTDI_SIO_baudrate_t ;typedef enum {  ftdi_8U232AM_12MHz_b300 = 0x09c4,  ftdi_8U232AM_12MHz_b600 = 0x04E2,  ftdi_8U232AM_12MHz_b1200 = 0x0271,  ftdi_8U232AM_12MHz_b2400 = 0x4138,  ftdi_8U232AM_12MHz_b4800 = 0x809c,  ftdi_8U232AM_12MHz_b9600 = 0xc04e,  ftdi_8U232AM_12MHz_b19200 = 0x0027,  ftdi_8U232AM_12MHz_b38400 = 0x4013,  ftdi_8U232AM_12MHz_b57600 = 0x000d,  ftdi_8U232AM_12MHz_b115200 = 0x4006,  ftdi_8U232AM_12MHz_b230400 = 0x8003,} FTDI_8U232AM_12MHz_baudrate_t;/* Apparently all devices are 48MHz */typedef enum {  ftdi_8U232AM_48MHz_b300 = 0x2710,  ftdi_8U232AM_48MHz_b600 = 0x1388,  ftdi_8U232AM_48MHz_b1200 = 0x09c4,  ftdi_8U232AM_48MHz_b2400 = 0x04e2,  ftdi_8U232AM_48MHz_b4800 = 0x0271,  ftdi_8U232AM_48MHz_b9600 = 0x4138,  ftdi_8U232AM_48MHz_b19200 = 0x809c,  ftdi_8U232AM_48MHz_b38400 = 0xc04e,  ftdi_8U232AM_48MHz_b57600 = 0x0034,  ftdi_8U232AM_48MHz_b115200 = 0x001a,  ftdi_8U232AM_48MHz_b230400 = 0x000d,  ftdi_8U232AM_48MHz_b460800 = 0x4006,  ftdi_8U232AM_48MHz_b921600 = 0x8003,} FTDI_8U232AM_48MHz_baudrate_t;#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )#define FTDI_SIO_SET_BREAK (0x1 << 14)/* FTDI_SIO_SET_DATA *//* * BmRequestType:  0100 0000B  * bRequest:       FTDI_SIO_SET_DATA * wValue:         Data characteristics (see below) * wIndex:         Port * wLength:        0 * Data:           No * * Data characteristics * *   B0..7   Number of data bits *   B8..10  Parity *           0 = None *           1 = Odd *           2 = Even *           3 = Mark *           4 = Space *   B11..13 Stop Bits *           0 = 1 *           1 = 1.5 *           2 = 2 *   B14 *           1 = TX ON (break) *           0 = TX OFF (normal state) *   B15 Reserved * *//* FTDI_SIO_MODEM_CTRL */#define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40#define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL/*  * BmRequestType:   0100 0000B * bRequest:        FTDI_SIO_MODEM_CTRL * wValue:          ControlValue (see below) * wIndex:          Port * wLength:         0 * Data:            None * * NOTE: If the device is in RTS/CTS flow control, the RTS set by this * command will be IGNORED without an error being returned * Also - you can not set DTR and RTS with one control message */#define FTDI_SIO_SET_DTR_MASK 0x1#define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))#define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))#define FTDI_SIO_SET_RTS_MASK 0x2#define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))#define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))/* * ControlValue * B0    DTR state *          0 = reset *          1 = set * B1    RTS state *          0 = reset *          1 = set * B2..7 Reserved * B8    DTR state enable *          0 = ignore *          1 = use DTR state * B9    RTS state enable *          0 = ignore *          1 = use RTS state * B10..15 Reserved *//* FTDI_SIO_SET_FLOW_CTRL */#define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40#define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL#define FTDI_SIO_DISABLE_FLOW_CTRL 0x0 #define FTDI_SIO_RTS_CTS_HS (0x1 << 8)#define FTDI_SIO_DTR_DSR_HS (0x2 << 8)#define FTDI_SIO_XON_XOFF_HS (0x4 << 8)/* *   BmRequestType:  0100 0000b *   bRequest:       FTDI_SIO_SET_FLOW_CTRL *   wValue:         Xoff/Xon *   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port *   wLength:        0  *   Data:           None * * hIndex protocol is: *   B0 Output handshaking using RTS/CTS *       0 = disabled *       1 = enabled *   B1 Output handshaking using DTR/DSR *       0 = disabled *       1 = enabled *   B2 Xon/Xoff handshaking *       0 = disabled *       1 = enabled * * A value of zero in the hIndex field disables handshaking * * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character  * and the lValue field contains the XON character. */   /* * FTDI_SIO_SET_EVENT_CHAR  * * Set the special event character for the specified communications port. * If the device sees this character it will immediately return the * data read so far - rather than wait 40ms or until 62 bytes are read * which is what normally happens. */#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40/*  *  BmRequestType:   0100 0000b *  bRequest:        FTDI_SIO_SET_EVENT_CHAR *  wValue:          EventChar *  wIndex:          Port *  wLength:         0 *  Data:            None * * wValue: *   B0..7   Event Character *   B8      Event Character Processing *             0 = disabled *             1 = enabled *   B9..15  Reserved * */          /* FTDI_SIO_SET_ERROR_CHAR *//* Set the parity error replacement character for the specified communications port *//*  *  BmRequestType:  0100 0000b *  bRequest:       FTDI_SIO_SET_EVENT_CHAR *  wValue:         Error Char *  wIndex:         Port *  wLength:        0 *  Data:           None * *Error Char *  B0..7  Error Character *  B8     Error Character Processing *           0 = disabled *           1 = enabled *  B9..15 Reserved * *//* FTDI_SIO_GET_MODEM_STATUS *//* Retreive the current value of the modem status register */#define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0#define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS#define FTDI_SIO_CTS_MASK 0x10#define FTDI_SIO_DSR_MASK 0x20#define FTDI_SIO_RI_MASK  0x40#define FTDI_SIO_RLSD_MASK 0x80/*  *   BmRequestType:   1100 0000b *   bRequest:        FTDI_SIO_GET_MODEM_STATUS *   wValue:          zero *   wIndex:          Port *   wLength:         1 *   Data:            Status *  * One byte of data is returned  * B0..3 0 * B4    CTS *         0 = inactive *         1 = active * B5    DSR *         0 = inactive *         1 = active * B6    Ring Indicator (RI) *         0 = inactive *         1 = active * B7    Receive Line Signal Detect (RLSD) *         0 = inactive *         1 = active  *//* Descriptors returned by the device  *  *  Device Descriptor *  * Offset	Field		Size	Value	Description * 0	bLength		1	0x12	Size of descriptor in bytes * 1	bDescriptorType	1	0x01	DEVICE Descriptor Type * 2	bcdUSB		2	0x0110	USB Spec Release Number * 4	bDeviceClass	1	0x00	Class Code * 5	bDeviceSubClass	1	0x00	SubClass Code * 6	bDeviceProtocol	1	0x00	Protocol Code * 7	bMaxPacketSize0 1	0x08	Maximum packet size for endpoint 0 * 8	idVendor	2	0x0403	Vendor ID * 10	idProduct	2	0x8372	Product ID (FTDI_SIO_PID) * 12	bcdDevice	2	0x0001	Device release number * 14	iManufacturer	1	0x01	Index of man. string desc * 15	iProduct	1	0x02	Index of prod string desc * 16	iSerialNumber	1	0x02	Index of serial nmr string desc * 17	bNumConfigurations 1    0x01	Number of possible configurations *  * Configuration Descriptor *  * Offset	Field			Size	Value * 0	bLength			1	0x09	Size of descriptor in bytes * 1	bDescriptorType		1	0x02	CONFIGURATION Descriptor Type * 2	wTotalLength		2	0x0020	Total length of data * 4	bNumInterfaces		1	0x01	Number of interfaces supported * 5	bConfigurationValue	1	0x01	Argument for SetCOnfiguration() req * 6	iConfiguration		1	0x02	Index of config string descriptor * 7	bmAttributes		1	0x20	Config characteristics Remote Wakeup * 8	MaxPower		1	0x1E	Max power consumption *  * Interface Descriptor *  * Offset	Field			Size	Value * 0	bLength			1	0x09	Size of descriptor in bytes * 1	bDescriptorType		1	0x04	INTERFACE Descriptor Type * 2	bInterfaceNumber	1	0x00	Number of interface * 3	bAlternateSetting	1	0x00	Value used to select alternate * 4	bNumEndpoints		1	0x02	Number of endpoints * 5	bInterfaceClass		1	0xFF	Class Code * 6	bInterfaceSubClass	1	0xFF	Subclass Code * 7	bInterfaceProtocol	1	0xFF	Protocol Code * 8	iInterface		1	0x02	Index of interface string description *  * IN Endpoint Descriptor *  * Offset	Field			Size	Value * 0	bLength			1	0x07	Size of descriptor in bytes * 1	bDescriptorType		1	0x05	ENDPOINT descriptor type * 2	bEndpointAddress	1	0x82	Address of endpoint * 3	bmAttributes		1	0x02	Endpoint attributes - Bulk * 4	bNumEndpoints		2	0x0040	maximum packet size * 5	bInterval		1	0x00	Interval for polling endpoint *  * OUT Endpoint Descriptor *  * Offset	Field			Size	Value * 0	bLength			1	0x07	Size of descriptor in bytes * 1	bDescriptorType		1	0x05	ENDPOINT descriptor type * 2	bEndpointAddress	1	0x02	Address of endpoint * 3	bmAttributes		1	0x02	Endpoint attributes - Bulk * 4	bNumEndpoints		2	0x0040	maximum packet size * 5	bInterval		1	0x00	Interval for polling endpoint *      * DATA FORMAT *  * IN Endpoint *  * The device reserves the first two bytes of data on this endpoint to contain the current * values of the modem and line status registers. In the absence of data, the device  * generates a message consisting of these two status bytes every 40 ms *  * Byte 0: Modem Status *  * Offset	Description * B0	Reserved - must be 1 * B1	Reserved - must be 0 * B2	Reserved - must be 0 * B3	Reserved - must be 0 * B4	Clear to Send (CTS) * B5	Data Set Ready (DSR) * B6	Ring Indicator (RI) * B7	Receive Line Signal Detect (RLSD) *  * Byte 1: Line Status *  * Offset	Description * B0	Data Ready (DR) * B1	Overrun Error (OE) * B2	Parity Error (PE) * B3	Framing Error (FE) * B4	Break Interrupt (BI) * B5	Transmitter Holding Register (THRE) * B6	Transmitter Empty (TEMT) * B7	Error in RCVR FIFO *  */#define FTDI_RS_DR  1#define FTDI_RS_OE (1<<1)#define FTDI_RS_PE (1<<2)#define FTDI_RS_FE (1<<3)#define FTDI_RS_BI (1<<4)#define FTDI_RS_THRE (1<<5)#define FTDI_RS_TEMT (1<<6)#define FTDI_RS_FIFO  (1<<7)/* * OUT Endpoint *  * This device reserves the first bytes of data on this endpoint contain the length * and port identifier of the message. For the FTDI USB Serial converter the port  * identifier is always 1. *  * Byte 0: Line Status *  * Offset	Description * B0	Reserved - must be 1 * B1	Reserved - must be 0 * B2..7	Length of message - (not including Byte 0) *  */