# wavemode:
#      0=no data
#      1=output to device (system dependent. wave denotes the device driver)
#      2=VOC file output, incl. headers
#      3=output the raw wave stream to the file
# log:  The file to write the sb16 emulator messages to.
# loglevel:
#      0=no log
#      1=only midi program and bank changes
#      2=severe errors
#      3=all errors
#      4=all errors plus all port accesses
#      5=all errors and port accesses plus a lot of extra info
# dmatimer:
#      microseconds per second for a DMA cycle.  Make it smaller to fix
#      non-continous sound.  750000 is usually a good value.  This needs a
#      reasonably correct setting for IPS.
#
# For an example look at the next line:
#=======================================================================

#sb16: midimode=1, midi=/dev/midi00, wavemode=1, wave=/dev/dsp, loglevel=2, log=sb16.log, #dmatimer=600000

#=======================================================================
# VGA_UPDATE_INTERVAL:
# Video memory is scanned for updates and screen updated every so many
# virtual seconds.  The default is 300000, about 3Hz.  This is generally
# plenty.  Keep in mind that you must tweak the 'ips:' directive
# to be as close to the number of emulated instructions-per-second
# your workstation can do, for this to be accurate.
#
# Examples:
#   vga_update_interval: 250000
#=======================================================================
vga_update_interval: 300000

# using for Winstone '98 tests
#vga_update_interval:  100000

#=======================================================================
# KEYBOARD_SERIAL_DELAY:
# Approximate time in microseconds that it takes one character to
# be transfered from the keyboard to controller over the serial path.
# Examples:
#   keyboard_serial_delay: 200
#=======================================================================
keyboard_serial_delay: 200

#=======================================================================
# KEYBOARD_PASTE_DELAY:
# Approximate time in microseconds between attempts to paste
# characters to the keyboard controller. This leaves time for the
# guest os to deal with the flow of characters.  The ideal setting
# depends on how your operating system processes characters.  The
# default of 100000 usec (.1 seconds) was chosen because it works 
# consistently in Windows.
#
# If your OS is losing characters during a paste, increase the paste
# delay until it stops losing characters.
#
# Examples:
#   keyboard_paste_delay: 100000
#=======================================================================
keyboard_paste_delay: 100000

#=======================================================================
# FLOPPY_COMMAND_DELAY:
# Time in microseconds to wait before completing some floppy commands
# such as read/write/seek/etc, which normally have a delay associated.
# I had this hardwired to 50,000 before.
#
# Examples:
#   floppy_command_delay: 50000
#=======================================================================
floppy_command_delay: 50000

#=======================================================================
# IPS:
# Emulated Instructions Per Second.  This is the number of IPS that bochs
# is capable of running on your machine.  Read the note in config.h
# on how to find this.  Make sure to recompile after.
#
# IPS is used to calibrate many time-dependent events within the bochs 
# simulation.  For example, changing IPS affects the frequency of VGA
# updates, the duration of time before a key starts to autorepeat, and 
# the measurement of BogoMips and other benchmarks.
#
# Examples:
# Machine                                         Mips
# ________________________________________________________________
# 650Mhz Athlon K-7 with Linux 2.4.4/egcs-2.91.66 2 to 2.5 Mips
# 400Mhz Pentium II with Linux 2.0.36/egcs-1.0.3  1 to 1.8 Mips
# 166Mhz 64bit Sparc with Solaris 2.x             approx 0.75 Mips
# 200Mhz Pentium with Linux 2.x                   approx 0.5 Mips
#
#=======================================================================
ips: 4000000

#=======================================================================
# mouse: Not used in any of the GUI specific modules, but the option
#        bx_options.mouse_enabled is set to this value.  The idea,
#        is that the GUI code should not generate mouse events when
#        not enabled.  The hardware emualation itself is not disabled
#        by this.  This is to facilitate deterministic runs of bochs.
#
# Examples:
#   mouse: enabled=1
#   mouse: enabled=0
#
# I wouldn't recommend enabling the mouse by default, unless you have a
# really good reason to do so.
#=======================================================================
mouse: enabled=0

#=======================================================================
# private_colormap: Request that the GUI create and use it's own
#                   non-shared colormap.  This colormap will be used
#                   when in the bochs window.  If not enabled, a
#                   shared colormap scheme may be used.  Not implemented
#                   on all GUI's.
#
# Examples:
#   private_colormap: enabled=1
#   private_colormap: enabled=0
#=======================================================================
private_colormap: enabled=0

#=======================================================================
# fullscreen: ONLY IMPLEMENTED ON AMIGA
#             Request that Bochs occupy the entire screen instead of a 
#             window.
#
# Examples:
#   fullscreen: enabled=0
#   fullscreen: enabled=1
#=======================================================================
fullscreen: enabled=0
screenmode: name="sample"

#=======================================================================
# ne2k: NE2000 compatible ethernet adapter
#
# Examples:
# ne2k: ioaddr=IOADDR, irq=IRQ, mac=MACADDR, ethmod=MODULE, ethdev=DEVICE
#
# ioaddr, irc: You probably won't need to change ioaddr and irq, unless there
# are IRQ conflicts.
#
# mac: The MAC address MUST NOT match the address of any machine on the net.
# Also, the first byte must be an even number (bit 0 set means a multicast
# address), and you cannot use ff:ff:ff:ff:ff:ff because that's the broadcast
# address.  For the ethertap module, you must use fe:fd:00:00:00:01.  There may
# be other restrictions too.  To be safe, just use the b0:c4... address.
#
# ethdev: The ethdev value is the name of the network interface on your host
# platform.  On UNIX machines, you can get the name by running ifconfig.  On
# Windows machines, you must run niclist to get the name of the ethdev.
# Niclist source code is in misc/niclist.c and it is included in Windows 
# binary releases.
#=======================================================================
# ne2k: ioaddr=0x280, irq=9, mac=b0:c4:20:00:00:00, ethmod=fbsd, ethdev=xl0
# ne2k: ioaddr=0x280, irq=9, mac=b0:c4:20:00:00:00, ethmod=linux, ethdev=eth0
# ne2k: ioaddr=0x280, irq=9, mac=b0:c4:20:00:00:01, ethmod=win32, ethdev=MYCARD
# ne2k: ioaddr=0x280, irq=9, mac=fe:fd:00:00:00:01, ethmod=tap, ethdev=tap0

#=======================================================================
# KEYBOARD_MAPPING:
# This enables a remap of a physical localized keyboard to a 
# virtualized us keyboard, as the PC architecture expects.
# If enabled, the keymap file must be specified.
# 
# Examples:
#   keyboard_mapping: enabled=1, map=gui/keymaps/x11-pc-de.map
#=======================================================================
#keyboard_mapping: enabled=0, map=

#=======================================================================
# KEYBOARD_TYPE:
# Type of keyboard return by a "identify keyboard" command to the
# keyboard controler. It must be one of "xt", "at" or "mf".
# Defaults to "mf". It should be ok for almost everybody. A known
# exception is french macs, that do have a "at"-like keyboard.
#
# Examples:
#   keyboard_type: mf
#=======================================================================
#keyboard_type: mf

#=======================================================================
# other stuff
#=======================================================================
# magic_break

#load32bitOSImage: os=nullkernel, path=../kernel.img, iolog=../vga_io.log
#load32bitOSImage: os=linux, path=../linux.img, iolog=../vga_io.log, initrd=../initrd.img
i440fxsupport: enabled=0
#time0: 938581955

#=======================================================================
# for Macintosh, use the style of pathnames in the following
# examples.
#
# vgaromimage: :bios:VGABIOS-elpin-2.20
# romimage: file=:bios:BIOS-bochs-981222a, address=0xf0000
# floppya: 1_44=[fd:], status=inserted
#=======================================================================