/* *  Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" * *  Copyright (c) 2006 Olivier DANET <odanet@caramail.com> * *  This program is free software; you can redistribute it and/or modify *  it under the terms of the GNU General Public License as published by *  the Free Software Foundation; either version 2 of the License, or *  (at your option) any later version. * *  This program is distributed in the hope that it will be useful, *  but WITHOUT ANY WARRANTY; without even the implied warranty of *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the * *  GNU General Public License for more details. * *  You should have received a copy of the GNU General Public License *  along with this program; if not, write to the Free Software *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= */#ifndef MT2060_PRIV_H#define MT2060_PRIV_H// Uncomment the #define below to enable spurs checking. The results where quite unconvincing.// #define MT2060_SPURCHECK/* This driver is based on the information available in the datasheet of the   "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map :   I2C Address : 0x60   Reg.No |   B7   |   B6   |   B5   |   B4   |   B3   |   B2   |   B1   |   B0   | ( defaults )   --------------------------------------------------------------------------------       00 | [              PART             ] | [              REV              ] | R  = 0x63       01 | [             LNABAND           ] | [              NUM1(5:2)        ] | RW = 0x3F       02 | [                               DIV1                                ] | RW = 0x74       03 | FM1CA  | FM1SS  | [  NUM1(1:0)  ] | [              NUM2(3:0)        ] | RW = 0x00       04 |                                 NUM2(11:4)                          ] | RW = 0x08       05 | [                               DIV2                       ] |NUM2(12)| RW = 0x93       06 | L1LK   | [        TAD1          ] | L2LK   | [         TAD2         ] | R       07 | [                               FMF                                 ] | R       08 |   ?    | FMCAL  |   ?    |   ?    |   ?    |   ?    |   ?    | TEMP   | R       09 |   0    |   0    | [    FMGC     ] |   0    | GP02   | GP01   |   0    | RW = 0x20       0A | ??       0B |   0    |   0    |   1    |   1    |   0    |   0    | [   VGAG      ] | RW = 0x30       0C | V1CSE  |   1    |   1    |   1    |   1    |   1    |   1    |   1    | RW = 0xFF       0D |   1    |   0    | [                      V1CS                       ] | RW = 0xB0       0E | ??       0F | ??       10 | ??       11 | [             LOTO              ] |   0    |   0    |   1    |   0    | RW = 0x42       PART    : Part code      : 6 for MT2060       REV     : Revision code  : 3 for current revision       LNABAND : Input frequency range : ( See code for details )       NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details )       FM1CA  : Calibration Start Bit       FM1SS  : Calibration Single Step bit       L1LK   : LO1 Lock Detect       TAD1   : Tune Line ADC ( ? )       L2LK   : LO2 Lock Detect       TAD2   : Tune Line ADC ( ? )       FMF    : Estimated first IF Center frequency Offset ( ? )       FM1CAL : Calibration done bit       TEMP   : On chip temperature sensor       FMCG   : Mixer 1 Cap Gain ( ? )       GP01 / GP02 : Programmable digital outputs. Unconnected pins ?       V1CSE  : LO1 VCO Automatic Capacitor Select Enable ( ? )       V1CS   : LO1 Capacitor Selection Value ( ? )       LOTO   : LO Timeout ( ? )       VGAG   : Tuner Output gain*/#define I2C_ADDRESS 0x60#define REG_PART_REV   0#define REG_LO1C1      1#define REG_LO1C2      2#define REG_LO2C1      3#define REG_LO2C2      4#define REG_LO2C3      5#define REG_LO_STATUS  6#define REG_FM_FREQ    7#define REG_MISC_STAT  8#define REG_MISC_CTRL  9#define REG_RESERVED_A 0x0A#define REG_VGAG       0x0B#define REG_LO1B1      0x0C#define REG_LO1B2      0x0D#define REG_LOTO       0x11#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chipsstruct mt2060_priv {	struct mt2060_config *cfg;	struct i2c_adapter   *i2c;	u32 frequency;	u32 bandwidth;	u16 if1_freq;	u8  fmfreq;};#endif