///////////菜單顯示，鍵盤輸入例程////////////////
///////////lcd_menu.c////////////////////////////
#include "lcd.h"
#include "stdio.h"
#define SUB_MENU_NUM 3
#define MAIN_MENU_NUM 5
code uchar mainmenu[MAIN_MENU_NUM][16] ={"target1","sub_menu_demo","get int from key","get float  key","show key data"};
code uchar submenu0[SUB_MENU_NUM][16]={"submenu1","submenu2","submenu3"};
extern bit isline0;
xdata int intnumber;
xdata float floatnumber;
void get_int_number();
void showkeydata();
void target1();
void sub_target1();
void sub_target1();
void sub_target3();
void sub_menu_demo();
void config (void) ;
void get_int_number(){//從鍵盤獲取int型數據，并將之存入intnumber全局變量中
	showline("entry",0);//利用筆者自定義函數實現顯示
	while(scankey()==2);
	intnumber=getint();//獲取int型數據
	showline("number has saved",0);
	while(scankey()==2);
}
void get_float_number(){//從鍵盤獲取float型數據，并將之存入floatnumber全局變量中
	showline("entry",0);
	while(scankey()==2);
	floatnumber=getfloat();//獲取float型數據
	showline("number has saved",0);
	while(scankey()==2);
}
void showkeydata(){//顯示intnumber數據
	showline("entry",0);
	while(scankey()==2);
	isline0=1;//將顯示行控制到第一行
	printf("\nkey_int=%d",intnumber);//顯示于第一行,利用庫函數實現顯示
	printf("\nfloat=%.4f",floatnumber);//顯示于第二行
	delay1ms(3000);
}
void target1(){//任務1，顯示浮點數，事實上是顯示長整型數，并將小數點移位
	showline("entry",0);
	while(scankey()==2);
	showpage("show float",0);
	showf(intnumber,3,1);//小數點左移3位，即顯示數據帶3位小數
	delay1ms(3000);
}
void sub_target1(){//子任務1，調用showpage函數一次性顯示兩行內容
	showpage("sub_target1 start...","^_^");
	delay1ms(2000);
}
void sub_target2(){//子任務2，調用showline函數單行顯示
	showline("sub_target2 start...",0);//在第一行顯示內容
	showline("hello world",1);//在第二行顯示內容
	delay1ms(2000);
}
void sub_target3(){//子任務3
	int t=-346;
	showline("sub_target3 start...",0);//第一行顯示字符串
	showint(t,1);//第二行顯示int型數據（負數）
	delay1ms(2000);
}
void sub_menu_demo(){//二級菜單
	xdata uchar submenu;
	showline("entry",0);
	while(scankey()==2);
	while(1){
		submenu=menu_sec("SUB_MENU ",submenu0,SUB_MENU_NUM);
		if(submenu==0){
				showline("entry_M1",0);
				while(scankey()==2);
				sub_target1();
				goto sub_end;
		}
		if(submenu==1){
				showline("entry_M2",0);
				while(scankey()==2);
				sub_target2();
				goto sub_end;
		}
		if(submenu==2){
				showline("entry_M3",0);
				while(scankey()==2);
				sub_target3();
				goto sub_end;
		}
	}
	sub_end:;
}
void config (void) {
//看門狗禁止
    WDTCN = 0x07;	
    WDTCN = 0xDE;   
    WDTCN = 0xAD;
    SFRPAGE = 0x0F;
    XBR0 = 0x00;	
    XBR1 = 0x00;	
    XBR2 = 0x40;	//交叉開關使能，使得P0-P3口能輸出
    XBR3 = 0x00;    
    SFRPAGE = 0x0F;
    P0MDOUT = 0x00; //端口配置，P0-P3，P6-P7口為開漏輸出
    P1MDOUT = 0x00; 
    P2MDOUT = 0x00; 
    P3MDOUT = 0x00; 
    P4MDOUT = 0x00; //P4口為開漏，也可推挽
    P5MDOUT = 0x07; 
    P6MDOUT = 0x00; 
    P7MDOUT = 0x00; 
    P1MDIN = 0xFF;  //所有端口為數字輸入，沒有模擬輸入端口
    P2MDIN = 0xFF;  
    P3MDIN = 0xFF; 
    SFRPAGE = 0x0F;
    CLKSEL = 0x00;  
    OSCXCN = 0x00;	
    OSCICN = 0x84;	
    //采用內部晶振，為24.5MHZ8分頻
}   
main(){
	xdata uchar menuval;
	config();
	dispini();
	for(;;){//按左右翻頁鍵選擇菜單，按確認鍵進入菜單調用相應函數
		menuval=menu_sec("MAIN_MENU ",mainmenu,MAIN_MENU_NUM);//主菜單
		if(menuval==0){
			target1();
		}
		if(menuval==1){
			sub_menu_demo();//進入二級菜單
		}
		if(menuval==2){
			get_int_number();//從鍵盤輸入數據
		}
		if(menuval==3){
			get_float_number();//從鍵盤輸入數據
		}
		if(menuval==4){
			showkeydata();//顯示鍵盤所輸入的數據
		}
	}
}