?? s3c2410x.h
字號:
#define UERSTAT2 0x50008014 //UART 2 Rx error status
#define UFSTAT2 0x50008018 //UART 2 FIFO status
#define UMSTAT2 0x5000801c //UART 2 Modem status
#define UBRDIV2 0x50008028 //UART 2 Baud rate divisor#define UTXH0 0x50000020 //UART 0 Transmission Hold
#define URXH0 0x50000024 //UART 0 Receive buffer
#define UTXH1 0x50004020 //UART 1 Transmission Hold
#define URXH1 0x50004024 //UART 1 Receive buffer
#define UTXH2 0x50008020 //UART 2 Transmission Hold
#define URXH2 0x50008024 //UART 2 Receive buffer
#define OFS_ULCON (ULCON0-ULCON0) //UART Line control
#define OFS_UCON (UCON0-ULCON0) //UART Control
#define OFS_UFCON (UFCON0-ULCON0) //UART FIFO control
#define OFS_UMCON (UMCON0-ULCON0) //UART Modem control
#define OFS_UTRSTAT (UTRSTAT0-ULCON0)//UART Tx/Rx status
#define OFS_UERSTAT (UERSTAT0-ULCON0)//UART Rx error status
#define OFS_UFSTAT (UFSTAT0-ULCON0) //UART FIFO status
#define OFS_UMSTAT (UMSTAT0-ULCON0) //UART Modem status
#define OFS_UBRDIV (UBRDIV0-ULCON0) //UART Baud rate divisor#define OFS_UTXH (UTXH0-ULCON0) //UART Transmission Hold
#define OFS_URXH (URXH0-ULCON0) //UART Receive buffer// ULCON bits
#define SHF_ULCON_WL 0
#define MSK_ULCON_WL (0x3<<SHF_ULCON_WL)
#define VAL_ULCON_WL_5 (0x0<<SHF_ULCON_WL)
#define VAL_ULCON_WL_6 (0x1<<SHF_ULCON_WL)
#define VAL_ULCON_WL_7 (0x2<<SHF_ULCON_WL)
#define VAL_ULCON_WL_8 (0x3<<SHF_ULCON_WL)
#define SHF_ULCON_SB 2
#define MSK_ULCON_SB (0x1<<SHF_ULCON_SB)
#define VAL_ULCON_SB_1 (0x0<<SHF_ULCON_SB)
#define VAL_ULCON_SB_2 (0x1<<SHF_ULCON_SB)
#define SHF_ULCON_PM 3
#define MSK_ULCON_PM (0x7<<SHF_ULCON_PM)
#define VAL_ULCON_PM_N (0x0<<SHF_ULCON_PM)
#define VAL_ULCON_PM_O (0x4<<SHF_ULCON_PM)
#define VAL_ULCON_PM_E (0x5<<SHF_ULCON_PM)
#define VAL_ULCON_PM_FC1 (0x6<<SHF_ULCON_PM)
#define VAL_ULCON_PM_FC0 (0x7<<SHF_ULCON_PM)
#define SHF_ULCON_IRM 6
#define MSK_ULCON_IRM (0x1<<SHF_ULCON_IRM)
#define VAL_ULCON_IRM_N (0x0<<SHF_ULCON_IRM)
#define VAL_ULCON_IRM_IR (0x1<<SHF_ULCON_IRM)
// PWM TIMER
#define TCFG0 0x51000000 //Timer 0 configuration
#define TCFG1 0x51000004 //Timer 1 configuration
#define TCON 0x51000008 //Timer control
#define TCNTB0 0x5100000c //Timer count buffer 0
#define TCMPB0 0x51000010 //Timer compare buffer 0
#define TCNTO0 0x51000014 //Timer count observation 0
#define TCNTB1 0x51000018 //Timer count buffer 1
#define TCMPB1 0x5100001c //Timer compare buffer 1
#define TCNTO1 0x51000020 //Timer count observation 1
#define TCNTB2 0x51000024 //Timer count buffer 2
#define TCMPB2 0x51000028 //Timer compare buffer 2
#define TCNTO2 0x5100002c //Timer count observation 2
#define TCNTB3 0x51000030 //Timer count buffer 3
#define TCMPB3 0x51000034 //Timer compare buffer 3
#define TCNTO3 0x51000038 //Timer count observation 3
#define TCNTB4 0x5100003c //Timer count buffer 4
#define TCNTO4 0x51000040 //Timer count observation 4
// USB DEVICE
#define FUNC_ADDR_REG 0x52000140 //Function address
#define PWR_REG 0x52000144 //Power management
#define EP_INT_REG 0x52000148 //EP Interrupt pending and clear
#define USB_INT_REG 0x52000158 //USB Interrupt pending and clear
#define EP_INT_EN_REG 0x5200015c //Interrupt enable
#define USB_INT_EN_REG 0x5200016c
#define FRAME_NUM1_REG 0x52000170 //Frame number lower byte
#define FRAME_NUM2_REG 0x52000174 //Frame number higher byte
#define INDEX_REG 0x52000178 //Register index
#define MAXP_REG 0x52000180 //Endpoint max packet
#define EP0_CSR 0x52000184 //Endpoint 0 status
#define IN_CSR1_REG 0x52000184 //In endpoint control status
#define IN_CSR2_REG 0x52000188
#define OUT_CSR1_REG 0x52000190 //Out endpoint control status
#define OUT_CSR2_REG 0x52000194
#define OUT_FIFO_CNT1_REG 0x52000198 //Endpoint out write count
#define OUT_FIFO_CNT2_REG 0x5200019c
#define EP0_FIFO 0x520001c0 //Endpoint 0 FIFO
#define EP1_FIFO 0x520001c4 //Endpoint 1 FIFO
#define EP2_FIFO 0x520001c8 //Endpoint 2 FIFO
#define EP3_FIFO 0x520001cc //Endpoint 3 FIFO
#define EP4_FIFO 0x520001d0 //Endpoint 4 FIFO
#define EP1_DMA_CON 0x52000200 //EP1 DMA interface control
#define EP1_DMA_UNIT 0x52000204 //EP1 DMA Tx unit counter
#define EP1_DMA_FIFO 0x52000208 //EP1 DMA Tx FIFO counter
#define EP1_DMA_TTC_L 0x5200020c //EP1 DMA total Tx counter
#define EP1_DMA_TTC_M 0x52000210
#define EP1_DMA_TTC_H 0x52000214
#define EP2_DMA_CON 0x52000218 //EP2 DMA interface control
#define EP2_DMA_UNIT 0x5200021c //EP2 DMA Tx unit counter
#define EP2_DMA_FIFO 0x52000220 //EP2 DMA Tx FIFO counter
#define EP2_DMA_TTC_L 0x52000224 //EP2 DMA total Tx counter
#define EP2_DMA_TTC_M 0x52000228
#define EP2_DMA_TTC_H 0x5200022c
#define EP3_DMA_CON 0x52000240 //EP3 DMA interface control
#define EP3_DMA_UNIT 0x52000244 //EP3 DMA Tx unit counter
#define EP3_DMA_FIFO 0x52000248 //EP3 DMA Tx FIFO counter
#define EP3_DMA_TTC_L 0x5200024c //EP3 DMA total Tx counter
#define EP3_DMA_TTC_M 0x52000250
#define EP3_DMA_TTC_H 0x52000254
#define EP4_DMA_CON 0x52000258 //EP4 DMA interface control
#define EP4_DMA_UNIT 0x5200025c //EP4 DMA Tx unit counter
#define EP4_DMA_FIFO 0x52000260 //EP4 DMA Tx FIFO counter
#define EP4_DMA_TTC_L 0x52000264 //EP4 DMA total Tx counter
#define EP4_DMA_TTC_M 0x52000268
#define EP4_DMA_TTC_H 0x5200026c
// WATCH DOG TIMER
#define WTCON 0x53000000 //Watch-dog timer mode
#define WTDAT 0x53000004 //Watch-dog timer data
#define WTCNT 0x53000008 //Eatch-dog timer count
// IIC
#define IICCON 0x54000000 //IIC control
#define IICSTAT 0x54000004 //IIC status
#define IICADD 0x54000008 //IIC address
#define IICDS 0x5400000c //IIC data shift
// IIS
#define IISCON 0x55000000 //IIS Control
#define IISMOD 0x55000004 //IIS Mode
#define IISPSR 0x55000008 //IIS Prescaler
#define IISFCON 0x5500000c //IIS FIFO control
#define IISFIFO 0x55000010 //IIS FIFO entry
// I/O PORT
#define GPACON 0x56000000 //Port A control
#define GPADAT 0x56000004 //Port A data
#define GPBCON 0x56000010 //Port B control
#define GPBDAT 0x56000014 //Port B data
#define GPBUP 0x56000018 //Pull-up control B
#define GPCCON 0x56000020 //Port C control
#define GPCDAT 0x56000024 //Port C data
#define GPCUP 0x56000028 //Pull-up control C
#define GPDCON 0x56000030 //Port D control
#define GPDDAT 0x56000034 //Port D data
#define GPDUP 0x56000038 //Pull-up control D
#define GPECON 0x56000040 //Port E control
#define GPEDAT 0x56000044 //Port E data
#define GPEUP 0x56000048 //Pull-up control E
#define GPFCON 0x56000050 //Port F control
#define GPFDAT 0x56000054 //Port F data
#define GPFUP 0x56000058 //Pull-up control F
#define GPGCON 0x56000060 //Port G control
#define GPGDAT 0x56000064 //Port G data
#define GPGUP 0x56000068 //Pull-up control G
#define GPHCON 0x56000070 //Port H control
#define GPHDAT 0x56000074 //Port H data
#define GPHUP 0x56000078 //Pull-up control H
#define MISCCR 0x56000080 //Miscellaneous control
#define DCLKCON 0x56000084 //DCLK0/1 control
#define EXTINT0 0x56000088 //External interrupt control register 0
#define EXTINT1 0x5600008c //External interrupt control register 1
#define EXTINT2 0x56000090 //External interrupt control register 2
#define EINTFLT0 0x56000094 //Reserved
#define EINTFLT1 0x56000098 //Reserved
#define EINTFLT2 0x5600009c //External interrupt filter control register 2
#define EINTFLT3 0x560000a0 //External interrupt filter control register 3
#define EINTMASK 0x560000a4 //External interrupt mask
#define EINTPEND 0x560000a8 //External interrupt pending
#define GSTATUS0 0x560000ac //External pin status
#define GSTATUS1 0x560000b0 //Chip ID(0x32410000)
#define GSTATUS2 0x560000b4 //Reset type
#define GSTATUS3 0x560000b8 //Saved data0(32-bit) before entering POWER_OFF mode
#define GSTATUS4 0x560000bc //Saved data0(32-bit) before entering POWER_OFF mode
// RTC
#define RTCCON 0x57000040 //RTC control
#define TICNT 0x57000044 //Tick time count
#define RTCALM 0x57000050 //RTC alarm control
#define ALMSEC 0x57000054 //Alarm second
#define ALMMIN 0x57000058 //Alarm minute
#define ALMHOUR 0x5700005c //Alarm Hour
#define ALMDAY 0x57000060 //Alarm day
#define ALMMON 0x57000064 //Alarm month
#define ALMYEAR 0x57000068 //Alarm year
#define RTCRST 0x5700006c //RTC round reset
#define BCDSEC 0x57000070 //BCD second
#define BCDMIN 0x57000074 //BCD minute
#define BCDHOUR 0x57000078 //BCD hour
#define BCDDAY 0x5700007c //BCD day
#define BCDDATE 0x57000080 //BCD date
#define BCDMON 0x57000084 //BCD month
#define BCDYEAR 0x57000088 //BCD year
// ADC
#define ADCCON 0x58000000 //ADC control
#define ADCTSC 0x58000004 //ADC touch screen control
#define ADCDLY 0x58000008 //ADC start or Interval Delay
#define ADCDAT0 0x5800000c //ADC conversion data 0
#define ADCDAT1 0x58000010 //ADC conversion data 1
// SPI
#define SPCON0 0x59000000 //SPI0 control
#define SPSTA0 0x59000004 //SPI0 status
#define SPPIN0 0x59000008 //SPI0 pin control
#define SPPRE0 0x5900000c //SPI0 baud rate prescaler
#define SPTDAT0 0x59000010 //SPI0 Tx data
#define SPRDAT0 0x59000014 //SPI0 Rx data
#define SPCON1 0x59000020 //SPI1 control
#define SPSTA1 0x59000024 //SPI1 status
#define SPPIN1 0x59000028 //SPI1 pin control
#define SPPRE1 0x5900002c //SPI1 baud rate prescaler
#define SPTDAT1 0x59000030 //SPI1 Tx data
#define SPRDAT1 0x59000034 //SPI1 Rx data
// SD Interface
#define SDICON 0x5a000000 //SDI control
#define SDIPRE 0x5a000004 //SDI baud rate prescaler
#define SDICARG 0x5a000008 //SDI command argument
#define SDICCON 0x5a00000c //SDI command control
#define SDICSTA 0x5a000010 //SDI command status
#define SDIRSP0 0x5a000014 //SDI response 0
#define SDIRSP1 0x5a000018 //SDI response 1
#define SDIRSP2 0x5a00001c //SDI response 2
#define SDIRSP3 0x5a000020 //SDI response 3
#define SDIDTIMER 0x5a000024 //SDI data/busy timer
#define SDIBSIZE 0x5a000028 //SDI block size
#define SDIDCON 0x5a00002c //SDI data control
#define SDIDCNT 0x5a000030 //SDI data remain counter
#define SDIDSTA 0x5a000034 //SDI data status
#define SDIFSTA 0x5a000038 //SDI FIFO status
#define SDIIMSK 0x5a000040 //SDI interrupt mask
#define SDIDAT 0x5a00003c //SDI data
#endif // CYGONCE_SMDK2410_H//-----------------------------------------------------------------------------// end of s3c2410x.h?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -