?? 12232.c
字號:
/*============================================================
功能：使用12232液晶顯示圖片演示
作者: Mingtree ycxms88@163.com http://www.mcu123.com
==============================================================
硬件：TG12232B （122*32）模擬口線接線方式
連接線圖:
--------------------------------------------------|
|DB0-----P0.0 | DB4-----P0.4 | RW-------P1.1 | A0--------P1.0 |
|DB1-----P0.1 | DB5-----P0.5 | RS-------P2.1 | V0接1K電阻到GND |
|DB2-----P0.2 | DB6-----P0.6 | E1-------P1.3 |
|DB3-----P0.3 | DB7-----P0.7 | E2-------P1.2 |
---------------------------------------------------
本程序源碼只供學習參考,如有需要請聯系作者。
[注:AT89x52使用22.1184M或11.0592M晶振,實測使用22.1184M或11.0592都可以]
編譯平臺：Keil uV2 7.08
//可能看起來有點亂，不過效果還是不錯的，顯示圖形總的來說比顯示漢字要簡單,當然顯示漢字也不難。
希望此程序能給你一些幫助。
有什么問題可以發email 給我或到我的論壇發問.
http://www.mcu123.com/bbs
=============================================================*/
#include <SST89x5x4.h>
#include <stdio.h>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
#define lcd_data P0 //數據
#define NOP() _nop_()
sfr P4=0xA5;
sbit E1 =P2^7; //塊1 左邊
sbit E2 =P2^6; //塊2 右邊
sbit RW =P2^1; //1-read,0-write
sbit A0 =P2^0; //A0為1時是數據，0時為指令數據
sbit W_R= P3^6;
extern unsigned char code Bmpt1[];
extern unsigned char code Bmpt2[];
extern unsigned char code Bmpt3[];
extern unsigned char code Bmpt4[];
extern unsigned char code Bmpt5[];
extern unsigned char code Bmpt6[];
extern unsigned char code Bmpt7[];
extern unsigned char code Bmptc[];
extern unsigned char code bmp001[];
extern unsigned char code Bmp08[];
extern unsigned char code Bmp07[];
extern unsigned char code Bmp06[];
extern unsigned char code Bmp05[];
extern unsigned char code Bmp04[];
extern unsigned char code Bmp03[];
extern unsigned char code Bmp02[];
extern unsigned char code Bmp01[];
extern unsigned char code Bmp012[];
extern unsigned char code Bmp003[];
extern unsigned char code Bmp002[];
//延時
void delay(unsigned int i)
{
unsigned char k=200;
while(i>0)
{
i--;
}
while(k>1)k--;
}
//左頁
//發送數據
void OUTMD(unsigned char i)
{
E2=0; //關S
E1=1; //開M
delay(5);
A0=1; //數據
WR=0; //寫觸發
NOP();
lcd_data = i;
NOP();
E1=0; //關M
}
//左頁
//發送命令
void OUTMI(unsigned char i)
{
E2=0; //關S
E1=1; //開M
delay(5);
A0=0; //指令
WR=0; //寫觸發
NOP();
lcd_data = i;
NOP();
E1=0; //關M
}
//右頁
//發送數據
void OUTSD(unsigned char i)
{
E1=0; //關S
E2=1; //開M
delay(5);
A0=1; //數據
WR=0; //寫觸發
NOP();
lcd_data = i;
NOP();
E2=0; //關M
}
//右頁
//發送命令
void OUTSI(unsigned char i)
{
E1=0; //關S
E2=1; //開M
delay(5);
A0=0; //指令
WR=0; //寫觸發
NOP();
lcd_data = i;
NOP();
E2=0; //關M
}
//初始化
void lcdini(void)
{
RW=0;
OUTMI(0XE2);
OUTSI(0XE2);//復位
OUTMI(0XAE);
OUTSI(0XAE);//POWER SAVE
OUTMI(0XA4);
OUTSI(0XA4);//動態驅動
OUTMI(0XA9);
OUTSI(0XA9);//1/32占空比
OUTMI(0XA0);
OUTSI(0XA0);//時鐘線輸出
OUTMI(0XEE);
OUTSI(0XEE);//寫模式
OUTMI(0X00);
OUTMI(0XC0);
OUTSI(0X00);
OUTSI(0XC0);
OUTMI(0XAF);
OUTSI(0XAF);
}
/*
函數說明：同時設置主從顯示頁為0－3頁。（內函數，私有，用戶不直接調用）
------------------------------------------------------------------------
*/
void SetPage(uchar page0,uchar page1)
{
OUTMI(0xB8|page1);OUTSI(0xB8|page0);
}
/*
--------------------------------------------------------------------------------
函數說明：同時設置主從列地址為0－121。（內函數，私有，用戶不直接調用）
--------------------------------------------------------------------------------
*/
void SetAddress(uchar address0,uchar address1)
{
OUTMI(address1);OUTSI(address0);
}
/*
--------------------------------------------------------------------------------
調用方式：void PutChar0(uchar ch)
函數說明：在右頁當前地址畫一個字節8個點。（內函數，私有，用戶不直接調用）
--------------------------------------------------------------------------------
-*/
void PutCharR(unsigned char ch_buffer1)//unsigned char ch_buffer
{
OUTSD(ch_buffer1);
}
/*
--------------------------------------------------------------------------------
調用方式：void PutChar1(uchar ch)
函數說明：在左頁當前地址畫一個字節8個點。（內函數，私有，用戶不直接調用）
--------------------------------------------------------------------------------
-*/
void PutCharL(unsigned char ch_buffer2)//unsigned char ch_buffer
{
OUTMD(ch_buffer2);
}
/*
--------------------------------------------------------------------------------
調用方式：void DrawBmp(bit layer,uchar width,uchar *bmp)
函數說明：畫一個圖,layer表示上下層，width是圖形的寬，高都是16，bmp是
圖形指針
使用zimo3軟件，縱向取模，字節倒序/240字節
--------------------------------------------------------------------------------
-*/
void DrawBmp(bit layer,uchar width,uchar *bmp)
{
uchar x,address,i=0; //address表示顯存的物理地址
uchar page=0; //page表示上下兩頁
bit window=0; //window表示左右兩頁
//putcharR //右邊
//putcharL //左邊
for (x=width;x>1;x--)
{
if (i>60) {window=1;address=i%61;}
else address=i;
if(layer==0) //顯示一行八個字
{
SetPage(0,0);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i]);
else PutCharL(bmp[i]);
SetPage(1,1);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i+width]);
else PutCharL(bmp[i+width]);
}
else
{ //顯示第二行八個漢字
SetPage(2,2);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i]);
else PutCharL(bmp[i]);
SetPage(3,3);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i+width]);
else PutCharL(bmp[i+width]);
}
i++;
}
}
/*
--------------------------------------------------------------------------------
調用方式：void clrscr(void)
函數說明：清屏
--------------------------------------------------------------------------------
-*/
void clrscr(void)
{
uchar i;
uchar page;
for (page=0;page<4;page++)
{
SetPage(page,page);
SetAddress(0,0);
for (i=0;i<61;i++){PutCharR(0);PutCharL(0);}
}
}
//-----------------------------------------------------------
//圖片顯示
//采用字模2生成或字模3生成的都可以.
//-----------------------------------------------------------
void DrawBmp1(uint x_add, uchar width,uchar *bmp)
{
uchar x,address,i=0; //address表示顯存的物理地址
uchar page=0; //page表示上下兩頁
bit window=0; //window表示左右兩頁
//putcharR //右邊
//putcharL //左邊
for (x=width;x>1;x--)
{
if (x_add>60) {window=1;address=x_add%61;}
else address=x_add;
SetPage(0,0);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i]);
else PutCharL(bmp[i]);
SetPage(1,1);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i+width]);
else PutCharL(bmp[i+width]);
SetPage(2,2);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i+width+width]);
else PutCharL(bmp[i+width+width]);
SetPage(3,3);
SetAddress(address,address);
if(window==1)PutCharR(bmp[i+width+width+width]);
else PutCharL(bmp[i+width+width+width]);
i++;
x_add++;
}
}
//---------------------------------------------------------------
//---------------------------------------------------------------
//采用zimo2 顯示漢字,以漢字的顯示方式
//void Draw_word(uchar d_where,uint x_add,bit layer,uchar width)
//d_where表示在碼表中第幾個漢字，x_add橫坐標位置,layer顯示的層, width顯示的寬度。
//---------------------------------------------------------------
void Draw_word(uchar d_where,uint x_add,bit layer,uchar width)
{
uchar x,i=0,address; //address表示顯存的物理地址
uchar page=0; //page表示上下兩頁
bit window=0; //window表示左右兩頁
//putcharR //右邊
//putcharL //左邊
d_where=d_where*32;
for (x=width;x>1;x--)
{
if (x_add>60) {window=1;address=x_add%61;}
else address=x_add;
if(layer==0) //顯示一行八個字
{
SetPage(0,0);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[d_where]);//右邊
else PutCharL(bmp001[d_where]);//左邊
SetPage(1,1);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[d_where+width]);
else PutCharL(bmp001[d_where+width]);
}
else
{ //顯示第二行八個漢字
SetPage(2,2);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[d_where]);//右邊
else PutCharL(bmp001[d_where]);//左邊
SetPage(3,3);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[d_where+width]);
else PutCharL(bmp001[d_where+width]);
}
x_add++;
d_where++;
}
}
/*
//------------------------------------------------------------------
//字模2顯示一個漢字
//縱向取模，字節倒序
void disp_one(bit top_low,bit widows,uchar address,uchar width,uchar*bmp)
{
if(top_low==0)
{
SetPage(0,0);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[next][i]);
else PutCharL(bmp001[next][i]);
SetPage(1,1);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[next][i+width]);
else PutCharL(bmp001[next][i+width]);
}
else
{
SetPage(0,0);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[next][i]);
else PutCharL(bmp001[next][i]);
SetPage(1,1);
SetAddress(address,address);
if(window==1)PutCharR(bmp001[next][i+width]);
else PutCharL(bmp001[next][i+width]);
}
}
*/
//液晶顯示規則
// M(左) S(右)
// page page
// 0 | 0
// 1 | 1
// 2 | 2
// 3 | 3
void delay1s(unsigned char i)
{
while(i>1)
{
i--;
delay(65530);
}
}
//顯示動態的等待圖標
void wait1(unsigned char i)
{
for(;i>1;i--)
{delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt1); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt2); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt3); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt4); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt5); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt6); //.
delay1s(2);
clrscr(); //.
DrawBmp1(0,60,Bmptc); //.
DrawBmp1(76,19,Bmpt7); //.
}
}
//演示程序
void main()
{
//W_R=0;
AUXR=0x02;
lcdini(); //reset
clrscr(); //clr
/*Draw_word(0,0,0,16); //
Draw_word(1,16,0,16); //
Draw_word(2,32,0,16); //
Draw_word(3,48,0,16); //
Draw_word(0,64,0,16); //
Draw_word(1,80,0,16); //
Draw_word(2,96,0,16); //
DrawBmp(1,120,Bmp002); //
clrscr(); //
delay1s(3);
DrawBmp1(0,122,Bmp012); //LOGO*/
while(1)
{
if(W_R==0)
{
P4 &= 0xFB;
delay(50);
//P4 |= 0xFF;
P4 &= 0xFD;
delay(50);
//P4 |= 0xFF;
}
Draw_word(0,0,0,16); //.
Draw_word(1,16,0,16); //.
Draw_word(2,32,0,16); //.
Draw_word(3,48,0,16); //.
Draw_word(0,64,0,16); //.
Draw_word(1,80,0,16); //.
Draw_word(2,96,0,16); //.
/* delay1s(3);
clrscr();
DrawBmp1(10,101,Bmp07);
//delay1s(8);
clrscr();
//wait1(3);
DrawBmp1(0,122,Bmp04);
//delay1s(8);
clrscr();
//wait1(3);
DrawBmp1(0,122,Bmp03); //合能電氣
//delay1s(8);
clrscr();
//wait1(3);
clrscr();
DrawBmp1(10,101,Bmp05);
//delay1s(8);
clrscr();
//wait1(3);
clrscr();
DrawBmp1(10,101,Bmp06);
//delay1s(8);
clrscr();
//wait1(3);
clrscr();
DrawBmp1(10,101,Bmp08);
//delay1s(8);
clrscr();
//wait1(3);
clrscr();
DrawBmp1(0,122,Bmp01); //這仿真器真不錯,用過都說好.
//wait1(8);*/
}
}
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -