//連上J15短路環.
//-----------------------------------------------------------------------------
// Includes
//-----------------------------------------------------------------------------
#include <c8051f350.h>                 // SFR declarations
#include <INTRINS.H>
#include <stdio.h>
//-----------------------------------------------------------------------------
// Global CONSTANTS
//-----------------------------------------------------------------------------
#define  uchar unsigned char
#define  uint  unsigned int

#define SYSCLK    24500000            // SYSCLK frequency in Hz

//----------------------------------------------------------------------------

void writelcd(uchar disdata);

unsigned char xdata discode;           //開關顯示、光標、閃爍的命令字暫存單元
unsigned long x;
unsigned char  virt_port;

unsigned char xdata tab1[16]   ={0x20,0x20,0x42,0x54,0x20,0x46,0x33,0x33,0x30,0x20,0x56,0x31,0x2e,0x30
                                  ,0x20,0x20};
unsigned char xdata Netdata[16]={0x77,0x77,0x77,0x2e,0x78,0x68,0x6c,0x2e,0x63,0x6f,
                                  0x6d,0x2e,0x63,0x6e,0x20,0x20}; 

sbit   LCDCS  = P1^2; 
                  

//-----------------------------------------------------------------------------
// PORT_Init
//-----------------------------------------------------------------------------


void PORT_Init (void)
{  P0SKIP    = 0x7E;
    
   XBR0 = 0x02;                       // Enable SMBus pins
   XBR1 = 0x40;                       // Enable crossbar and weak pull-ups

   P0MDOUT |= 0x01;                    // All P0 pins open-drain output
   P1MDOUT = 0x05;
 

}
//-----------------------------------------------------------------------------
//SPI_INIT
//-----------------------------------------------------------------------------
void SPI0_Init (void)
{
   SPI0CFG = 0x70;                     // data sampled on 1st SCK rising edge
                                       // 8-bit data words

   SPI0CN = 0x09;                      // Master mode; SPI enabled; flags
                                       // cleared
   SPI0CKR = 0x03;//SYSCLK/2/3000000-1;// SPI clock <= 8MHz (limited by 
                                       // EEPROM spec.)
}
//-----------------------------------------------------------------------------
//write com
//-----------------------------------------------------------------------------
void Write_COM(uchar ins)
     {
      uchar xdata i,t;
	  uint xdata j;
	 
	  for(j=0;j<500;j++);	            	//用延時代替查詢
	  virt_port|=ins&0xf0;
	  writelcd(virt_port);
     
	  virt_port|=0x08;
	  writelcd(virt_port);
      for(i=3;i>0;i--);
     
	  virt_port&=~0x08;
	  writelcd(virt_port);

      virt_port&=0x07;
	  writelcd(virt_port);
      t=ins<<4;             
      virt_port|=t&0xf0;           
	  writelcd(virt_port);
    
	  virt_port|=0x08;
	  writelcd(virt_port);
      for(i=3;i>0;i--);
    
	  virt_port&=~0x08;
	  writelcd(virt_port);
      virt_port=0;
	  writelcd(virt_port);
     }
//----------------------------------------------------------------------------------
//write data
//----------------------------------------------------------------------------------
void Write_CHAR(uchar d)
    {
      uchar xdata i,t;
	  uint xdata j;
	 
      for(j=0;j<500;j++);		//用延時代替查詢
	  virt_port|=0x02;
	  writelcd(virt_port);
      virt_port|=d&0xf0;
	  writelcd(virt_port);
      virt_port|=0x08;//E=1
	  writelcd(virt_port);
      for(i=3;i>0;i--);
      virt_port&=0xf7; //E=0
	  writelcd(virt_port);
      virt_port&=0x07;				
	  writelcd(virt_port);
	       
      t=d&0x0f;
      virt_port|=t<<4;
	  writelcd(virt_port);

	  virt_port|=0x08; //E=1
	  writelcd(virt_port);
      for(i=3;i>0;i--); 
      virt_port&=0xf7; //E=0
	  writelcd(virt_port);
      virt_port=0;
	  writelcd(virt_port);
    }



//------------------------------------------------------------------------------------------
void YJ_Init(void)
     {
      uint xdata i;
                                     // setting (24500000)
   PORT_Init ();                        // initialize crossbar and GPIO
   SPI0_Init ();
      virt_port=0;
	  writelcd(virt_port);
      virt_port|=0x08;       	//E=1，第一步
	  writelcd(virt_port);
      virt_port|=0x30;
	  writelcd(virt_port);
	  for(i=20;i>0;i--); 
      virt_port&=0xf7;    		//E=0
	  writelcd(virt_port);
      virt_port=0;
	  writelcd(virt_port);
      for(i=20000;i>0;i--);
      for(i=20000;i>0;i--);
	  	
      virt_port|=0x08;     	    //E=1，第二步
	  writelcd(virt_port);
      virt_port|=0x30;
	  writelcd(virt_port);
	  for(i=20;i>0;i--); 
      virt_port&=0xf7;    		//E=0
	  writelcd(virt_port);
      virt_port=0;
	  writelcd(virt_port);
      for(i=1000;i>0;i--);

      virt_port|=0x08;     	    //E=1，第三步
	  writelcd(virt_port);
      virt_port|=0x30;
	  writelcd(virt_port);
	  for(i=20;i>0;i--); 
      virt_port&=0xf7;    		//E=0
	  writelcd(virt_port);
      virt_port=0;
	  writelcd(virt_port);
      for(i=1000;i>0;i--);	    //3次延時，重要！
	
	  for(i=8000;i>0;i--);		//用延時代替查詢	  

    
      virt_port=0;				//第五步，寫入20碼，設置為4位總線方式,非常重要！！！！！
	  writelcd(virt_port);
      virt_port|=0x20;			//只寫高字節
	  writelcd(virt_port);
      virt_port|=0x08;          //E=1
	  writelcd(virt_port);
	  for(i=20;i>0;i--);
      virt_port&=0xf7;          //E=0
	  writelcd(virt_port);
	  for(i=10;i>0;i--);
      virt_port=0;
	  writelcd(virt_port);

      Write_COM(0x28);		    //第六步。。。。
      for(i=50;i>0;i--);

	  Write_COM(0x01);
      for(i=50;i>0;i--);

      Write_COM(0x0e);
      for(i=50;i>0;i--);     

      Write_COM(0x06);
      for(i=50;i>0;i--);

     }
//-----------------------------------------------------
void writelcd(uchar disdata)     //write 595
	{
	uint xdata i;

	for(i=0;i<3;i++);
	LCDCS=1;
    SPIF = 0;
    for(x=0;x<50;x++);
	SPI0DAT=disdata;

    while (SPIF == 0);	 		// 等待寫結束
    for(x=0;x<500;x++);
	LCDCS=0;
    for(x=0;x<500;x++);	
	}
//----------------------------------------------------------
//end