?? 2440addr.h
字號(hào):
#define URXH0 (0x50000024+3)
#define UTXH1 (0x50004020+3)
#define URXH1 (0x50004024+3)
#define UTXH2 (0x50008020+3)
#define URXH2 (0x50008024+3)
#else //Little Endian
#define rUTXH0 (*(volatile unsigned char *)0x50000020) //UART 0 Transmission Hold
#define rURXH0 (*(volatile unsigned char *)0x50000024) //UART 0 Receive buffer
#define rUTXH1 (*(volatile unsigned char *)0x50004020) //UART 1 Transmission Hold
#define rURXH1 (*(volatile unsigned char *)0x50004024) //UART 1 Receive buffer
#define rUTXH2 (*(volatile unsigned char *)0x50008020) //UART 2 Transmission Hold
#define rURXH2 (*(volatile unsigned char *)0x50008024) //UART 2 Receive buffer
#define WrUTXH0(ch) (*(volatile unsigned char *)0x50000020)=(unsigned char)(ch)
#define RdURXH0() (*(volatile unsigned char *)0x50000024)
#define WrUTXH1(ch) (*(volatile unsigned char *)0x50004020)=(unsigned char)(ch)
#define RdURXH1() (*(volatile unsigned char *)0x50004024)
#define WrUTXH2(ch) (*(volatile unsigned char *)0x50008020)=(unsigned char)(ch)
#define RdURXH2() (*(volatile unsigned char *)0x50008024)
#define UTXH0 (0x50000020) //Byte_access address by DMA
#define URXH0 (0x50000024)
#define UTXH1 (0x50004020)
#define URXH1 (0x50004024)
#define UTXH2 (0x50008020)
#define URXH2 (0x50008024)
#endif
// PWM TIMER
#define rTCFG0 (*(volatile unsigned *)0x51000000) //Timer 0 configuration
#define rTCFG1 (*(volatile unsigned *)0x51000004) //Timer 1 configuration
#define rTCON (*(volatile unsigned *)0x51000008) //Timer control
#define rTCNTB0 (*(volatile unsigned *)0x5100000c) //Timer count buffer 0
#define rTCMPB0 (*(volatile unsigned *)0x51000010) //Timer compare buffer 0
#define rTCNTO0 (*(volatile unsigned *)0x51000014) //Timer count observation 0
#define rTCNTB1 (*(volatile unsigned *)0x51000018) //Timer count buffer 1
#define rTCMPB1 (*(volatile unsigned *)0x5100001c) //Timer compare buffer 1
#define rTCNTO1 (*(volatile unsigned *)0x51000020) //Timer count observation 1
#define rTCNTB2 (*(volatile unsigned *)0x51000024) //Timer count buffer 2
#define rTCMPB2 (*(volatile unsigned *)0x51000028) //Timer compare buffer 2
#define rTCNTO2 (*(volatile unsigned *)0x5100002c) //Timer count observation 2
#define rTCNTB3 (*(volatile unsigned *)0x51000030) //Timer count buffer 3
#define rTCMPB3 (*(volatile unsigned *)0x51000034) //Timer compare buffer 3
#define rTCNTO3 (*(volatile unsigned *)0x51000038) //Timer count observation 3
#define rTCNTB4 (*(volatile unsigned *)0x5100003c) //Timer count buffer 4
#define rTCNTO4 (*(volatile unsigned *)0x51000040) //Timer count observation 4
// USB DEVICE
#ifdef __BIG_ENDIAN
<ERROR IF BIG_ENDIAN>
#define rFUNC_ADDR_REG (*(volatile unsigned char *)0x52000143) //Function address
#define rPWR_REG (*(volatile unsigned char *)0x52000147) //Power management
#define rEP_INT_REG (*(volatile unsigned char *)0x5200014b) //EP Interrupt pending and clear
#define rUSB_INT_REG (*(volatile unsigned char *)0x5200015b) //USB Interrupt pending and clear
#define rEP_INT_EN_REG (*(volatile unsigned char *)0x5200015f) //Interrupt enable
#define rUSB_INT_EN_REG (*(volatile unsigned char *)0x5200016f)
#define rFRAME_NUM1_REG (*(volatile unsigned char *)0x52000173) //Frame number lower byte
#define rFRAME_NUM2_REG (*(volatile unsigned char *)0x52000177) //Frame number higher byte
#define rINDEX_REG (*(volatile unsigned char *)0x5200017b) //Register index
#define rMAXP_REG (*(volatile unsigned char *)0x52000183) //Endpoint max packet
#define rEP0_CSR (*(volatile unsigned char *)0x52000187) //Endpoint 0 status
#define rIN_CSR1_REG (*(volatile unsigned char *)0x52000187) //In endpoint control status
#define rIN_CSR2_REG (*(volatile unsigned char *)0x5200018b)
#define rOUT_CSR1_REG (*(volatile unsigned char *)0x52000193) //Out endpoint control status
#define rOUT_CSR2_REG (*(volatile unsigned char *)0x52000197)
#define rOUT_FIFO_CNT1_REG (*(volatile unsigned char *)0x5200019b) //Endpoint out write count
#define rOUT_FIFO_CNT2_REG (*(volatile unsigned char *)0x5200019f)
#define rEP0_FIFO (*(volatile unsigned char *)0x520001c3) //Endpoint 0 FIFO
#define rEP1_FIFO (*(volatile unsigned char *)0x520001c7) //Endpoint 1 FIFO
#define rEP2_FIFO (*(volatile unsigned char *)0x520001cb) //Endpoint 2 FIFO
#define rEP3_FIFO (*(volatile unsigned char *)0x520001cf) //Endpoint 3 FIFO
#define rEP4_FIFO (*(volatile unsigned char *)0x520001d3) //Endpoint 4 FIFO
#define rEP1_DMA_CON (*(volatile unsigned char *)0x52000203) //EP1 DMA interface control
#define rEP1_DMA_UNIT (*(volatile unsigned char *)0x52000207) //EP1 DMA Tx unit counter
#define rEP1_DMA_FIFO (*(volatile unsigned char *)0x5200020b) //EP1 DMA Tx FIFO counter
#define rEP1_DMA_TTC_L (*(volatile unsigned char *)0x5200020f) //EP1 DMA total Tx counter
#define rEP1_DMA_TTC_M (*(volatile unsigned char *)0x52000213)
#define rEP1_DMA_TTC_H (*(volatile unsigned char *)0x52000217)
#define rEP2_DMA_CON (*(volatile unsigned char *)0x5200021b) //EP2 DMA interface control
#define rEP2_DMA_UNIT (*(volatile unsigned char *)0x5200021f) //EP2 DMA Tx unit counter
#define rEP2_DMA_FIFO (*(volatile unsigned char *)0x52000223) //EP2 DMA Tx FIFO counter
#define rEP2_DMA_TTC_L (*(volatile unsigned char *)0x52000227) //EP2 DMA total Tx counter
#define rEP2_DMA_TTC_M (*(volatile unsigned char *)0x5200022b)
#define rEP2_DMA_TTC_H (*(volatile unsigned char *)0x5200022f)
#define rEP3_DMA_CON (*(volatile unsigned char *)0x52000243) //EP3 DMA interface control
#define rEP3_DMA_UNIT (*(volatile unsigned char *)0x52000247) //EP3 DMA Tx unit counter
#define rEP3_DMA_FIFO (*(volatile unsigned char *)0x5200024b) //EP3 DMA Tx FIFO counter
#define rEP3_DMA_TTC_L (*(volatile unsigned char *)0x5200024f) //EP3 DMA total Tx counter
#define rEP3_DMA_TTC_M (*(volatile unsigned char *)0x52000253)
#define rEP3_DMA_TTC_H (*(volatile unsigned char *)0x52000257)
#define rEP4_DMA_CON (*(volatile unsigned char *)0x5200025b) //EP4 DMA interface control
#define rEP4_DMA_UNIT (*(volatile unsigned char *)0x5200025f) //EP4 DMA Tx unit counter
#define rEP4_DMA_FIFO (*(volatile unsigned char *)0x52000263) //EP4 DMA Tx FIFO counter
#define rEP4_DMA_TTC_L (*(volatile unsigned char *)0x52000267) //EP4 DMA total Tx counter
#define rEP4_DMA_TTC_M (*(volatile unsigned char *)0x5200026b)
#define rEP4_DMA_TTC_H (*(volatile unsigned char *)0x5200026f)
#else // Little Endian
#define rFUNC_ADDR_REG (*(volatile unsigned char *)0x52000140) //Function address
#define rPWR_REG (*(volatile unsigned char *)0x52000144) //Power management
#define rEP_INT_REG (*(volatile unsigned char *)0x52000148) //EP Interrupt pending and clear
#define rUSB_INT_REG (*(volatile unsigned char *)0x52000158) //USB Interrupt pending and clear
#define rEP_INT_EN_REG (*(volatile unsigned char *)0x5200015c) //Interrupt enable
#define rUSB_INT_EN_REG (*(volatile unsigned char *)0x5200016c)
#define rFRAME_NUM1_REG (*(volatile unsigned char *)0x52000170) //Frame number lower byte
#define rFRAME_NUM2_REG (*(volatile unsigned char *)0x52000174) //Frame number higher byte
#define rINDEX_REG (*(volatile unsigned char *)0x52000178) //Register index
#define rMAXP_REG (*(volatile unsigned char *)0x52000180) //Endpoint max packet
#define rEP0_CSR (*(volatile unsigned char *)0x52000184) //Endpoint 0 status
#define rIN_CSR1_REG (*(volatile unsigned char *)0x52000184) //In endpoint control status
#define rIN_CSR2_REG (*(volatile unsigned char *)0x52000188)
#define rOUT_CSR1_REG (*(volatile unsigned char *)0x52000190) //Out endpoint control status
#define rOUT_CSR2_REG (*(volatile unsigned char *)0x52000194)
#define rOUT_FIFO_CNT1_REG (*(volatile unsigned char *)0x52000198) //Endpoint out write count
#define rOUT_FIFO_CNT2_REG (*(volatile unsigned char *)0x5200019c)
#define rEP0_FIFO (*(volatile unsigned char *)0x520001c0) //Endpoint 0 FIFO
#define rEP1_FIFO (*(volatile unsigned char *)0x520001c4) //Endpoint 1 FIFO
#define rEP2_FIFO (*(volatile unsigned char *)0x520001c8) //Endpoint 2 FIFO
#define rEP3_FIFO (*(volatile unsigned char *)0x520001cc) //Endpoint 3 FIFO
#define rEP4_FIFO (*(volatile unsigned char *)0x520001d0) //Endpoint 4 FIFO
#define rEP1_DMA_CON (*(volatile unsigned char *)0x52000200) //EP1 DMA interface control
#define rEP1_DMA_UNIT (*(volatile unsigned char *)0x52000204) //EP1 DMA Tx unit counter
#define rEP1_DMA_FIFO (*(volatile unsigned char *)0x52000208) //EP1 DMA Tx FIFO counter
#define rEP1_DMA_TTC_L (*(volatile unsigned char *)0x5200020c) //EP1 DMA total Tx counter
#define rEP1_DMA_TTC_M (*(volatile unsigned char *)0x52000210)
#define rEP1_DMA_TTC_H (*(volatile unsigned char *)0x52000214)
#define rEP2_DMA_CON (*(volatile unsigned char *)0x52000218) //EP2 DMA interface control
#define rEP2_DMA_UNIT (*(volatile unsigned char *)0x5200021c) //EP2 DMA Tx unit counter
#define rEP2_DMA_FIFO (*(volatile unsigned char *)0x52000220) //EP2 DMA Tx FIFO counter
#define rEP2_DMA_TTC_L (*(volatile unsigned char *)0x52000224) //EP2 DMA total Tx counter
#define rEP2_DMA_TTC_M (*(volatile unsigned char *)0x52000228)
#define rEP2_DMA_TTC_H (*(volatile unsigned char *)0x5200022c)
#define rEP3_DMA_CON (*(volatile unsigned char *)0x52000240) //EP3 DMA interface control
#define rEP3_DMA_UNIT (*(volatile unsigned char *)0x52000244) //EP3 DMA Tx unit counter
#define rEP3_DMA_FIFO (*(volatile unsigned char *)0x52000248) //EP3 DMA Tx FIFO counter
#define rEP3_DMA_TTC_L (*(volatile unsigned char *)0x5200024c) //EP3 DMA total Tx counter
#define rEP3_DMA_TTC_M (*(volatile unsigned char *)0x52000250)
#define rEP3_DMA_TTC_H (*(volatile unsigned char *)0x52000254)
#define rEP4_DMA_CON (*(volatile unsigned char *)0x52000258) //EP4 DMA interface control
#define rEP4_DMA_UNIT (*(volatile unsigned char *)0x5200025c) //EP4 DMA Tx unit counter
#define rEP4_DMA_FIFO (*(volatile unsigned char *)0x52000260) //EP4 DMA Tx FIFO counter
#define rEP4_DMA_TTC_L (*(volatile unsigned char *)0x52000264) //EP4 DMA total Tx counter
#define rEP4_DMA_TTC_M (*(volatile unsigned char *)0x52000268)
#define rEP4_DMA_TTC_H (*(volatile unsigned char *)0x5200026c)
#endif // __BIG_ENDIAN
// WATCH DOG TIMER
#define rWTCON (*(volatile unsigned *)0x53000000) //Watch-dog timer mode
#define rWTDAT (*(volatile unsigned *)0x53000004) //Watch-dog timer data
#define rWTCNT (*(volatile unsigned *)0x53000008) //Eatch-dog timer count
// IIC
#define rIICCON (*(volatile unsigned *)0x54000000) //IIC control
#define rIICSTAT (*(volatile unsigned *)0x54000004) //IIC status
#define rIICADD (*(volatile unsigned *)0x54000008) //IIC address
#define rIICDS (*(volatile unsigned *)0x5400000c) //IIC data shift
#define rIICLC (*(volatile unsigned *)0x54000010) //IIC multi-master line control
// IIS
#define rIISCON (*(volatile unsigned *)0x55000000) //IIS Control
#define rIISMOD (*(volatile unsigned *)0x55000004) //IIS Mode
#define rIISPSR (*(volatile unsigned *)0x55000008) //IIS Prescaler
#define rIISFCON (*(volatile unsigned *)0x5500000c) //IIS FIFO control
#ifdef __BIG_ENDIAN
#define IISFIFO ((volatile unsigned short *)0x55000012) //IIS FIFO entry
#else //Little Endian
#define IISFIFO ((volatile unsigned short *)0x55000010) //IIS FIFO entry
#endif
//AC97, Added for S3C2440A
#define rAC_GLBCTRL *(volatile unsigned *)0x5b000000
#define rAC_GLBSTAT *(volatile unsigned *)0x5b000004
#define rAC_CODEC_CMD *(volatile unsigned *)0x5b000008
#define rAC_CODEC_STAT *(volatile unsigned *)0x5b00000C
#define rAC_PCMADDR *(volatile unsigned *)0x5b000010
#define rAC_MICADDR *(volatile unsigned *)0x5b000014
#define rAC_PCMDATA *(volatile unsigned *)0x5b000018
#define rAC_MICDATA *(volatile unsigned *)0x5b00001C
#define AC_PCMDATA 0x5b000018
#define AC_MICDATA 0x5b00001C
// I/O PORT
#define rGPACON (*(volatile unsigned *)0x56000000) //Port A control
#define rGPADAT (*(volatile unsigned *)0x56000004) //Port A data
#define rGPBCON (*(volatile unsigned *)0x56000010) //Port B control
#define rGPBDAT (*(volatile unsigned *)0x56000014) //Port B data
#define rGPBUP (*(volatile unsigned *)0x56000018) //Pull-up control B
#define rGPCCON (*(volatile unsigned *)0x56000020) //Port C control
#define rGPCDAT (*(volatile unsigned *)0x56000024) //Port C data
#define rGPCUP (*(volatile unsigned *)0x56000028) //Pull-up control C
#define rGPDCON (*(volatile unsigned *)0x56000030) //Port D control
#define rGPDDAT (*(volatile unsigned *)0x56000034) //Port D data
#define rGPDUP (*(volatile unsigned *)0x56000038) //Pull-up control D
#define rGPECON (*(volatile unsigned *)0x56000040) //Port E control
#define rGPEDAT (*(volatile unsigned *)0x56000044) //Port E data
#define rGPEUP (*(volatile unsigned *)0x56000048) //Pull-up control E
#define rGPFCON (*(volatile unsigned *)0x56000050) //Port F control
#define rGPFDAT (*(volatile unsigned *)0x56000054) //Port F data
#define rGPFUP (*(volatile unsigned *)0x56000058) //Pull-up control F
#define rGPGCON (*(volatile unsigned *)0x56000060) //Port G control
#define rGPGDAT (*(volatile unsigned *)0x56000064) //Port G data
#define rGPGUP (*(volatile unsigned *)0x56000068) //Pull-up control G
#define rGPHCON (*(volatile unsigned *)0x56000070) //Port H control
#define rGPHDAT (*(volatile unsigned *)0x56000074) //Port H data
#define rGPHUP (*(volatile unsigned *)0x56000078) //Pull-up control H
#define rGPJCON (*(volatile unsigned *)0x560000d0) //Port J control
#define rGPJDAT (*(volatile unsigned *)0x560000d4) //Port J data
#define rGPJUP (*(volatile unsigned *)0x560000d8) //Pull-up control J
?? 快捷鍵說明
復(fù)制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號(hào)
Ctrl + =
減小字號(hào)
Ctrl + -