;-  ----------------------------------------------------------------------------
;-          ATMEL Microcontroller Software Support  -  ROUSSET  -
;-  ----------------------------------------------------------------------------
;-  DISCLAIMER:  THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
;-  IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
;-  MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
;-  DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
;-  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
;-  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
;-  OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
;-  LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
;-  NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
;-  EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
;-  ----------------------------------------------------------------------------
;- File source          : Cstartup.s79
;- Object               : Generic CStartup
;- 1.0 01/Sep/05 FBr    : Creation
;------------------------------------------------------------------------------

;------------------------------------------------------------------------------
; Include your AT91 Library files
;------------------------------------------------------------------------------
#include "include/AT91SAM7X256_inc.h"
;------------------------------------------------------------------------------

;------------------------------------------------------------------------------
; ?RESET
; Reset Vector.
; Normally, segment INTVEC is linked at address 0.
; For debugging purposes, INTVEC may be placed at other addresses.
; A debugger that honors the entry point will start the
; program in a normal way even if INTVEC is not at address 0.
;------------------------------------------------------------------------------

    PROGRAM	?RESET              ;- Begins a program module
    RSEG	INTRAMEND_REMAP     ;- Begins a relocatable segment
    RSEG	ICODE:CODE (2)      ;- Begins a relocatable segment : corresponding address is 32-bit aligned
    CODE32	                    ;- Always ARM mode after reset	
    ORG	0	                    ;- Sets the location counter: corresponds to the RESET vector address

;------------------------------------------------------------------------------
;- Exception vectors
;------------------------------------------------------------------------------
;- These vectors can be read at address 0 or at RAM address
;- They ABSOLUTELY requires to be in relative addresssing mode in order to
;- guarantee a valid jump. For the moment, all are just looping.
;- If an exception occurs before remap, this would result in an infinite loop.
;- To ensure if a exeption occurs before start application to infinite loop.
;------------------------------------------------------------------------------

reset
                B           InitReset           ; 0x00 Reset handler
undefvec:
                B           undefvec            ; 0x04 Undefined Instruction
swivec:
                B           swivec              ; 0x08 Software Interrupt
pabtvec:
                B           pabtvec             ; 0x0C Prefetch Abort
dabtvec:
                B           dabtvec             ; 0x10 Data Abort
rsvdvec:
                B           rsvdvec             ; 0x14 reserved
irqvec:
                B           IRQ_Handler_Entry   ; 0x18 IRQ
fiqvec:               				
                B           fiqvec              ; 0x1c FIQ

InitReset:

;------------------------------------------------------------------------------
;- Low level Init is performed in a C function: AT91F_LowLevelInit
;- Init Stack Pointer to a valid memory area before calling AT91F_LowLevelInit
;------------------------------------------------------------------------------

;- Retrieve end of RAM address
__iramend EQU SFB(INTRAMEND_REMAP)      ;- Segment begin

    EXTERN   AT91F_LowLevelInit
    ldr     r13,=__iramend              ;- Temporary stack in internal RAM for Low Level Init execution
    ldr	    r0,=AT91F_LowLevelInit
    mov     lr, pc
    bx	    r0                          ;- Branch on C function (with interworking)

;------------------------------------------------------------------------------
;- Top of Stack Definition
;------------------------------------------------------------------------------
;- Interrupt and Supervisor Stack are located at the top of internal memory in
;- order to speed the exception handling context saving and restoring.
;- ARM_MODE_SVC (Application, C) Stack is located at the top of the external memory.
;------------------------------------------------------------------------------

IRQ_STACK_SIZE          EQU     (3*8*4)     ; 3 words to be saved per interrupt priority level
ARM_MODE_IRQ            EQU     0x12
ARM_MODE_SVC            EQU     0x13
I_BIT                   EQU     0x80
F_BIT                   EQU     0x40

;------------------------------------------------------------------------------
;- Setup the stack for each mode
;------------------------------------------------------------------------------
    ldr     r0, =__iramend

;- Set up Interrupt Mode and set IRQ Mode Stack
    msr     CPSR_c, #ARM_MODE_IRQ | I_BIT | F_BIT
    mov     r13, r0                     ; Init stack IRQ
    sub     r0, r0, #IRQ_STACK_SIZE

;- Enable interrupt & Set up Supervisor Mode and set Supervisor Mode Stack
    msr     CPSR_c, #ARM_MODE_SVC | F_BIT
    mov     r13, r0

;------------------------------------------------------------------------------
; Initialize segments.
;------------------------------------------------------------------------------
; __segment_init is assumed to use
; instruction set and to be reachable by BL from the ICODE segment
; (it is safest to link them in segment ICODE).
;------------------------------------------------------------------------------
    EXTERN	__segment_init
    ldr	r0,=__segment_init
    mov     lr, pc
    bx	r0

;------------------------------------------------------------------------------
;- Branch on C code Main function (with interworking)
;------------------------------------------------------------------------------
    EXTERN	main
    PUBLIC	__main
?jump_to_main:
    ldr	lr,=?call_exit
    ldr	r0,=main
__main:
    bx	r0

;------------------------------------------------------------------------------
;- Loop for ever
;------------------------------------------------------------------------------
;- End of application. Normally, never occur.
;- Could jump on Software Reset ( B 0x0 ).
;------------------------------------------------------------------------------
?call_exit:
End
    b       End

;------------------------------------------------------------------------------
;- Manage exception: The exception must be ensure in ARM mode
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
;- Function             : IRQ_Handler_Entry
;- Treatments           : IRQ Controller Interrupt Handler.
;- Called Functions     : AIC_IVR[interrupt]
;------------------------------------------------------------------------------
IRQ_Handler_Entry:

;-------------------------
;- Manage Exception Entry
;-------------------------
;- Adjust and save LR_irq in IRQ stack
    sub         lr, lr, #4
    stmfd       sp!, {lr}

;- Save r0 and SPSR (need to be saved for nested interrupt)
    mrs         r14, SPSR
    stmfd       sp!, {r0,r14}

;- Write in the IVR to support Protect Mode
;- No effect in Normal Mode
;- De-assert the NIRQ and clear the source in Protect Mode
    ldr         r14, =AT91C_BASE_AIC
    ldr         r0 , [r14, #AIC_IVR]
    str         r14, [r14, #AIC_IVR]

;- Enable Interrupt and Switch in Supervisor Mode
    msr         CPSR_c, #ARM_MODE_SVC

;- Save scratch/used registers and LR in User Stack
    stmfd       sp!, { r1-r3, r12, r14}

;----------------------------------------------
;- Branch to the routine pointed by the AIC_IVR
;----------------------------------------------
    mov         r14, pc
    bx          r0

;----------------------------------------------
;- Manage Exception Exit
;----------------------------------------------
;- Restore scratch/used registers and LR from User Stack
    ldmia       sp!, { r1-r3, r12, r14}

;- Disable Interrupt and switch back in IRQ mode
    msr         CPSR_c, #I_BIT | ARM_MODE_IRQ

;- Mark the End of Interrupt on the AIC
    ldr         r14, =AT91C_BASE_AIC
    str         r14, [r14, #AIC_EOICR]

;- Restore SPSR_irq and r0 from IRQ stack
    ldmia       sp!, {r0,r14}
    msr         SPSR_cxsf, r14

;- Restore adjusted  LR_irq from IRQ stack directly in the PC
    ldmia       sp!, {pc}^

;------------------------------------------------------------------------------
;- Exception Vectors
;------------------------------------------------------------------------------
    PUBLIC    AT91F_Default_FIQ_handler
    PUBLIC    AT91F_Default_IRQ_handler
    PUBLIC    AT91F_Spurious_handler

    CODE32      ; Always ARM mode after exeption

AT91F_Default_FIQ_handler
    b         AT91F_Default_FIQ_handler

AT91F_Default_IRQ_handler
    b         AT91F_Default_IRQ_handler

AT91F_Spurious_handler
    b         AT91F_Spurious_handler

    ENDMOD      ;- Terminates the assembly of the current module
    END         ;- Terminates the assembly of the last module in a file