MX 86000   512K, 800x600x256c/1024x768x16c
MX 86010   1MB, 1024x768x256colors


Support chips:
MX8602   Clock chip. Supplies 25.175, 28.322, 40,44.9, 14.3, 16.3, 36, 65 MHz


3C4h index 26h (R/W):
bit   0  Set for MX86000, clear for MX86010

3C4h index 30h-33h (R/W):  Scratch
Note: used by MXIC utilities to store the old IRQ 2 interrupt address.

3C4h index 34h (R/W):
bit 0-1  Monitor type: 0=VGA, 1=8514A, 2=NEC 3D, 3=NEC 4D

3C4h index 65h (R/W):
bit   6  Set to enable access to extended registers (3C4h index 8-FFh).

3C4h index 90h (R/W):
bit 0-1  ??

3C4h index A7h (W?):  Enable extensions
bit 0-7  Writing 87h to this register enables the MXIC extensions,
         writing 0 disables them.

3C4h index C2h (R/W):
bit 2-3  Video RAM installed: 0=256k, 1=512k, 2=1M

3C4h index C3h (R/W):
bit   2  Set to enable banked access via index C5h.
      3  If set doubles image horizontally
      7  Bus width?. 0=8 bit, 1=16 bit.

3C4h index C4h (R/W):
bit   0  Clock Select bit 2 (bits 0-1 are in 3C2h/3CCh bits 2-3)
      3  Select Memory Clock for Video Clock ?
    6,7  Disables display if set

3C4h index C5h (R/W):  Bank register
bit 0-3  Write bank in 64k blocks.
    4-7  Read bank in 64k blocks

3C4h index F0h (R/W):
bit 0-1  3 if interlaced, 0 if not.
      3  If clear the display will wrap at 256K.
      4  If set display width or scanline width is slightly wrong ?
      7  Disables display if set

3C4h index F1h (R/W):
bit 0-1  Display Start Address bit 16-17

3C4h index F2h (R/W):
bit   7  Set if IRQ2 enabled, clear if not.

3C4h index F3h (R/W):
bit   0  Scrambles display if set ?
      1  Vertical overflow ?
      2  Disables display if set
      3  If set the same (random ?) line is repeated down the entire screen
      5  Disables display if set
      6  If set the same (random ?) line is repeated down the entire screen
      7  If set image looses vertical sync ??

Apparently the sequencer (3C4/5h) does not decode bit 3-4 of the index, thus
index 7 is duplicated at 0Fh, 17h and 1Fh.


Test for MXIC chip:

old:=rdinx($3C4,$A7);
wrinx($3C4,$A7,0);     {Disable extensions}
if not testinx($3C4,$C5) then
begin
  wrinx($3C4,$A7,$87);
  if testinx($3C4,$C5) then
    if (rdinx($3C4,$26) and 1)=0 then MXIC MX86010
                                 else MXIC MX86000
end;
wrinx($3C4,$A7,old);


  Video modes:
    50h  T   132   25   16  (8x16)
    51h  T   132   30   16  (8x16)
    55h  G   800  600   16  PL4
    56h  G  1024  768   16  PL4
    57h  G   640  350  256  P8
    58h  G   640  400  256  P8
    59h  G   640  480  256  P8
    5Ah  G   800  600  256  P8
    5Bh  G  1024  768  256  P8