## Configuration for Boot Loader### System configurations#EM86XX_ARCH = TANGO15EM86XX_REV = 2BOARD = tron-mu-duDRAMBASE = 0x90000000LOADERBASE = 0x90060000STAGE1_IMAGE_SIZE = 0x10000DEFAULT_UART_PORT = 0DEFAULT_UART_BAUDRATE = 115200## Debugging configurations## To test boot loader without flashing itTESTLOADERONRAM = n# Debugging messageDEBUG = n## Production test#PRODUCTIONTEST = nSTAGE0_TEST_IMAGE_SIZE = 10496## DRAM adjustment and BIST#DRAMADJUSTMENT = yBIST = nSTAGE0_XTRA_IMAGE_SIZE = 5820#DEBUG_DRAMADJUSTMENT = n## Component configurations## RELEASE VERSION = y, DEVELOPER VERSION = nRELEASE = nENABLE_FULLFUNCTION = nENABLE_SFLASH = yENABLE_SFLASH_ST_M25 = nENABLE_SFLASH_ST_M95 = nENABLE_SFLASH_SST = yENABLE_FLASH = yENABLE_2NDBOOT = yENABLE_ROMFS2 = nENABLE_IDE = nENABLE_IDE_ISA = nENABLE_IDE_BM = nENABLE_FIP = nENABLE_PCI = nENABLE_PCIHOST_EM86XX = nENABLE_PCIHOST_FPGA = nENABLE_NETWORK = nENABLE_NETWORK_DNS = nENABLE_NETWORK_NE2KPCI = nENABLE_NETWORK_RTL81XX = nENABLE_NETWORK_TANGO15 = nENABLE_IRQHANDLER = yENABLE_BITMAPS = yENABLE_UCODES = nENABLE_USERPREF = nENABLE_VSYNCPARAM = yENABLE_DVI = nDISABLE_HELP_MSGS = n## Crypto#STAGE0_CRYPTO_IMAGE_SIZE = 7168ENABLE_CRYPTO = nENABLE_CRYPTO_FULL = nENCRYPTED_ROM0_NAME = "image.bin"## Extra encrypted & signed filesystems (see crypto/doc/readme.txt)#ENABLE_ENCRYPTED_OPT_ROM = n## Extra encrypted & signed filesystems settings (N/A if ENABLE_ENCRYPTED_OPT_ROM == n)##Since the parameters for extra fs are passed to the kernel on the command#line, any default command line set in the kernel will be overriden, use this#parameter to set any additionnal kernel command line parameter (as root=...).CRYPTO_KERNEL_CMDLINE = "root=/dev/blkmem/0"#DRAM size allocated for all extra roms _and_ linux kernelENCRYPTED_OPT_DRAM_SIZE = 0x2000000               #  32 MBENCRYPTED_ROM0_SIZE = 0x200000                    #   2 MBENCRYPTED_ROM0_ADDR = LOADER_FLASH_ROMFSADDRENCRYPTED_OPT_ROM1_NAME = "rom1.bin"ENCRYPTED_OPT_ROM1_ADDR = (ENCRYPTED_ROM0_ADDR + ENCRYPTED_ROM0_SIZE)ENCRYPTED_OPT_ROM1_SIZE = 0x20000                 # 128 KBENCRYPTED_OPT_ROM2_NAME = "rom2.bin"ENCRYPTED_OPT_ROM2_ADDR = (ENCRYPTED_OPT_ROM1_ADDR + ENCRYPTED_OPT_ROM1_SIZE)ENCRYPTED_OPT_ROM2_SIZE = 0x100000                #   1 MBENCRYPTED_OPT_ROM3_NAME = NULLENCRYPTED_OPT_ROM3_ADDR = 0ENCRYPTED_OPT_ROM3_SIZE = 0ENCRYPTED_OPT_ROM4_NAME = NULLENCRYPTED_OPT_ROM4_ADDR = 0ENCRYPTED_OPT_ROM4_SIZE = 0## Extra signed ROMFS (not encrypted, see crypto/doc/readme.txt)#ENABLE_SIGNED_OPT_ROM = n## Extra signed ROMFS settings (N/A if ENABLE_SIGNED_OPT_ROM == n)#SIGNED_OPT_ROM1_ADDR = (LOADER_FLASH_ROMFSADDR + 0x200000)SIGNED_OPT_ROM1_SIZE = 0x200000SIGNED_OPT_ROM2_ADDR = 0SIGNED_OPT_ROM2_SIZE = 0SIGNED_OPT_ROM3_ADDR = 0SIGNED_OPT_ROM3_SIZE = 0SIGNED_OPT_ROM4_ADDR = 0SIGNED_OPT_ROM4_SIZE = 0## For secondary bootloader & romfs#BOOT_2NDBOOT = nSTAGE2_IMAGE_SIZE = 131072MAX_ROMFS_SIZE = 7904#MAX_ROMFS2_SIZE = 4096#ROMFS2_OFFSET = 0x00400000## FIP panel#EM86XX_FIP = REF1## Default parameters## SystemDEFAULT_CLKGEN_PLL = 0x01010019# DRAM#DEFAULT_DRAM0_DUNIT_CFG = 0xf320013cDEFAULT_DRAM0_DUNIT_CFG = 0xf321113cDEFAULT_DRAM1_DUNIT_CFG = 0DEFAULT_DRAM0_SIZE = 6DEFAULT_DRAM1_SIZE = 0DEFAULT_DRAM_DUNIT_DELAY0_CTRL = 0x00089999# PCIDEFAULT_PCI_SUBSYSTEM_ID = 0x00000000DEFAULT_PCI_REVISION_ID = 0DEFAULT_PCI_MEMORY_SIZE = 0DEFAULT_CONFIGVALID = CONFIGVALID_PCISUBID# Serial FlashDEFAULT_SFLA_DRIVER_SPEED = 0x0f000003# Peripheral Bus# default# CS_CONFIG = 0x1044 for normal / 0x1844 for PCI-FPGADEFAULT_PB_DEFAULT_TIMING = 0x10101010DEFAULT_PB_CS_CONFIG = 0x00001044# 0 : Used by Flash / FlexROMDEFAULT_PB_TIMING0 = 0x01090008DEFAULT_PB_USE_TIMING0 = 0x000001f4# 1 : Used by IDE PIO/DMADEFAULT_PB_TIMING1 = 0x00110101DEFAULT_PB_USE_TIMING1 = 0x000003f3# 2 : ReservedDEFAULT_PB_TIMING2 = 0x00000000DEFAULT_PB_USE_TIMING2 = 0x00000000# 3 : ReservedDEFAULT_PB_TIMING3 = 0x00000000DEFAULT_PB_USE_TIMING3 = 0x00000000# 4 : ReservedDEFAULT_PB_TIMING4 = 0x00000000DEFAULT_PB_USE_TIMING4 = 0x00000000# 5 : ReservedDEFAULT_PB_TIMING5 = 0x00000000DEFAULT_PB_USE_TIMING5 = 0x00000000# InterruptDEFAULT_IRQ_GPIOMAP = 0x0a09080b# GPIODEFAULT_GPIO_DIR = 0xE0B7DEFAULT_GPIO_OUTPUT = 0x60B7# Clean Divider Frequencies#DEFAULT_CD0_FREQ_HZ = 33333333#DEFAULT_CD1_FREQ_HZ = 0#DEFAULT_CD2_FREQ_HZ = 96000000#DEFAULT_CD3_FREQ_HZ = 0# BootDEFAULT_BOOTFLAG = ( BOOTFLAG_BOOT | BOOTFLAG_LOAD(BOOTFLAG_LOAD_BITMAP) | BOOTFLAG_LOAD(BOOTFLAG_LOAD_VSYNCPARAM) | BOOTFLAG_LOAD(BOOTFLAG_LOAD_IRQHANDLER) | BOOTFLAG_BOOT_FIRST(BOOTFLAG_MEDIA_FLASH) )