//******************************************************************************
//  MSP-FET430P440 Demo - USART0, 9600 UART Echo ISR, DCO SMCLK
//
//  Description: Echo a received character, RX ISR used. Normal mode is LPM0.
//  USART0 RX interrupt triggers TX Echo.
//  Baud rate divider with 1048576hz = 1048576Hz/9600 = ~109.23 (06Dh|03h)
//  ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 1048576Hz
//  //* An external watch crystal between XIN & XOUT is required for ACLK *//	
//
//                MSP430F449
//             -----------------
//         /|\|              XIN|-
//          | |                 | 32kHz
//          --|RST          XOUT|-
//            |                 |
//            |             P2.4|----------->
//            |                 | 9600 - 8N1
//            |             P2.5|<-----------
//
//
//  M. Buccini
//  Texas Instruments Inc.
//  Feb 2005
//  Built with IAR Embedded Workbench Version: 3.21A
//*****************************************************************************
#include <msp430x44x.h>

void uart_config(void);                     //UART初始化設置函數
#define   Num_of_Results   8                //定義用于存放全局變量的數組
static char Rev_results[Num_of_Results]={50,49,49,50,50,50,50,50};
static char index = 0;

void uart_config(void){
  WDTCTL = WDTPW + WDTHOLD;                 // Stop WDT
  FLL_CTL0 |= XCAP18PF;                     // Configure load caps
  P2SEL |= 0x30;                            // P2.4,5 引腳為串口通信腳
  P2DIR |= 0xd0;                            // P2.4,P2.6,P2.7設置為輸出模式
  //P2OUT &= ~0x80;                         // 芯片供電撤消，供電結束
  P2OUT |= 0x80;                            // 芯片供電
  P2OUT |= 0x40;                            // 允許發送
  
  ME1 |= UTXE0 + URXE0;                     // Enable USART0 TXD/RXD
  UCTL0 |= CHAR;                            // 8位傳送模式
  UTCTL0 |= SSEL1;                          // UCLK = SMCLK
  UBR00 = 0x6D;                             // 調制波特率
  UBR10 = 0x00;                              
  UMCTL0 = 0x03;                             
  UCTL0 &= ~SWRST;                          // Initialize USART state machine
  IE1 |= UTXIE0;                            // 允許中斷
}
void main(void)
{
 // Rev_results[Num_of_Results]={1,2,3,4,5,6,7,8};
  uart_config();
  TXBUF0 = Rev_results[index];              // RXBUF0 to TXBUF0  
  _BIS_SR(LPM0_bits + GIE);                 // Enter LPM0 w/ interrupt
}

#pragma vector=UART0RX_VECTOR
__interrupt void usart0_rx (void)
{                                    // Increment results index, modulo
  if(index++<8){
    TXBUF0 = Rev_results[index++];              // RXBUF0 to TXBUF0
  }
  else{
    //IFG2 &=~UTXIFG1;
    ME1 &=~UTXE0;
  }                                   // SET BREAKPOINT HERE
  _NOP();
}