#include <common.h>#include <mpc8xx.h>#include <pcmcia.h>#undef	CONFIG_PCMCIA#if defined(CONFIG_CMD_PCMCIA)#define	CONFIG_PCMCIA#endif#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)#define	CONFIG_PCMCIA#endif#ifdef	CONFIG_PCMCIA#define PCMCIA_BOARD_MSG "ICU862"static void cfg_port_B (void){	volatile immap_t	*immap;	volatile cpm8xx_t	*cp;	uint reg;	immap = (immap_t *)CFG_IMMR;	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));	/*	* Configure Port B for TPS2205 PC-Card Power-Interface Switch	*	* Switch off all voltages, assert shutdown	*/	reg  = cp->cp_pbdat;	reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */			TPS2205_VCC3    | TPS2205_VCC5    |	/* VAVCC => Hi-Z */			TPS2205_SHDN);				/* enable switch */	cp->cp_pbdat = reg;	cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);	reg = cp->cp_pbdir & ~(TPS2205_INPUTS);	cp->cp_pbdir = reg | TPS2205_OUTPUTS;	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);}int pcmcia_hardware_enable(int slot){	volatile immap_t	*immap;	volatile cpm8xx_t	*cp;	volatile pcmconf8xx_t	*pcmp;	volatile sysconf8xx_t	*sysp;	uint reg, pipr, mask;	int i;	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);	udelay(10000);	immap = (immap_t *)CFG_IMMR;	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));	/* Configure Port B for TPS2205 PC-Card Power-Interface Switch */	cfg_port_B ();	/*	* Configure SIUMCR to enable PCMCIA port B	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)	*/	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */	/* clear interrupt state, and disable interrupts */	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);	/*	* Disable interrupts, DMA, and PCMCIA buffers	* (isolate the interface) and assert RESET signal	*/	debug ("Disable PCMCIA buffers and assert RESET\n");	reg  = 0;	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */	PCMCIA_PGCRX(_slot_) = reg;	udelay(500);	/*	* Make sure there is a card in the slot, then configure the interface.	*/	udelay(10000);	debug ("[%d] %s: PIPR(%p)=0x%x\n",	       __LINE__,__FUNCTION__,	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {		printf ("   No Card found\n");		return (1);	}	/*	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z	*/	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);	pipr = pcmp->pcmc_pipr;	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",	       pipr,	       (reg&PCMCIA_VS1(slot))?"n":"ff",	       (reg&PCMCIA_VS2(slot))?"n":"ff");	reg  = cp->cp_pbdat;	if ((pipr & mask) == mask) {		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */				TPS2205_VCC3);				/* 3V off	*/		reg &= ~(TPS2205_VCC5);				/* 5V on	*/		puts (" 5.0V card found: ");	} else {		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */				TPS2205_VCC5);				/* 5V off	*/		reg &= ~(TPS2205_VCC3);				/* 3V on	*/		puts (" 3.3V card found: ");	}	debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",	       reg,	       (reg & TPS2205_VCC3)    ? "off" : "on",	       (reg & TPS2205_VCC5)    ? "off" : "on",	       (reg & TPS2205_VPP_PGM) ? "off" : "on",	       (reg & TPS2205_VPP_VCC) ? "off" : "on" );	cp->cp_pbdat = reg;	/*  Wait 500 ms; use this to check for over-current */	for (i=0; i<5000; ++i) {		if ((cp->cp_pbdat & TPS2205_OC) == 0) {			printf ("   *** Overcurrent - Safety shutdown ***\n");			cp->cp_pbdat &= ~(TPS2205_SHDN);			return (1);		}		udelay (100);	}	debug ("Enable PCMCIA buffers and stop RESET\n");	reg  =  PCMCIA_PGCRX(_slot_);	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */	PCMCIA_PGCRX(_slot_) = reg;	udelay(250000);	/* some cards need >150 ms to come up :-( */	debug ("# hardware_enable done\n");	return (0);}#if defined(CONFIG_CMD_PCMCIA)int pcmcia_hardware_disable(int slot){	volatile immap_t	*immap;	volatile cpm8xx_t	*cp;	volatile pcmconf8xx_t	*pcmp;	u_long reg;	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);	immap = (immap_t *)CFG_IMMR;	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));	/* Shut down */	cp->cp_pbdat &= ~(TPS2205_SHDN);	/* Configure PCMCIA General Control Register */	debug ("Disable PCMCIA buffers and assert RESET\n");	reg  = 0;	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */	PCMCIA_PGCRX(_slot_) = reg;	udelay(10000);	return (0);}#endifint pcmcia_voltage_set(int slot, int vcc, int vpp){	volatile immap_t	*immap;	volatile cpm8xx_t	*cp;	volatile pcmconf8xx_t	*pcmp;	u_long reg;	debug ("voltage_set: "			PCMCIA_BOARD_MSG			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);	immap = (immap_t *)CFG_IMMR;	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));	/*	* Disable PCMCIA buffers (isolate the interface)	* and assert RESET signal	*/	debug ("Disable PCMCIA buffers and assert RESET\n");	reg  = PCMCIA_PGCRX(_slot_);	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */	PCMCIA_PGCRX(_slot_) = reg;	udelay(500);	/*	* Configure Port C pins for	* 5 Volts Enable and 3 Volts enable,	* Turn all power pins to Hi-Z	*/	debug ("PCMCIA power OFF\n");	cfg_port_B ();	/* Enables switch, but all in Hi-Z */	reg  = cp->cp_pbdat;	switch(vcc) {		case  0:			break;	/* Switch off		*/		case 33: reg &= ~TPS2205_VCC3;	break;	/* Switch on 3.3V	*/		case 50: reg &= ~TPS2205_VCC5;	break;	/* Switch on 5.0V	*/		default:			goto done;	}	/* Checking supported voltages */	debug ("PIPR: 0x%x --> %s\n",	       pcmp->pcmc_pipr,	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");	cp->cp_pbdat = reg;#ifdef DEBUG{	char *s;	if ((reg & TPS2205_VCC3) == 0) {		s = "at 3.3V";	} else if ((reg & TPS2205_VCC5) == 0) {		s = "at 5.0V";	} else {		s = "down";	}	printf ("PCMCIA powered %s\n", s);}#endifdone:	debug ("Enable PCMCIA buffers and stop RESET\n");	reg  =  PCMCIA_PGCRX(_slot_);	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */	PCMCIA_PGCRX(_slot_) = reg;	udelay(500);	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",	       slot+'A');	return (0);}#endif	/* CONFIG_PCMCIA */