#define F2_SREV             0x4020  // Silicon Revision register
#define F2_SREV_ID_M         0x000000FF // Mask to read SREV info
#define F2_SREV_FPGA         1
#define F2_SREV_D2PLUS       2
#define F2_SREV_D2PLUS_MS    3		// metal spin
#define F2_SREV_CRETE        4
#define F2_SREV_CRETE_MS     5		// FCS metal spin
#define F2_SREV_CRETE_MS23   7          // 2.3 metal spin (6 skipped)
#define F2_SREV_CRETE_23     8          // 2.3 full tape out

// EEPROM Registers in the MAC
#define F2_EEPROM_BASE	    0x6000  // Base register for EEPROM config
#define F2_EEPROM_RDATA	    0x6800  // EEPROM read data values
#define F2_EEPROM_STATUS    0x6c00  // Status register for EEPROM action status
#define F2_EEPROM_STAT_RDERR  0x0001 // Indicates a read error
#define F2_EEPROM_STAT_RDDONE 0x0002 // Indicates a read has completed
#define F2_EEPROM_STAT_WRERR  0x0004 // Indicates a write error
#define F2_EEPROM_STAT_WRDONE 0x0008 // Indicates a write has completed

// MAC PCU Registers
#define F2_STA_ID0          0x8000  // MAC station ID0 register - low 32 bits
#define F2_STA_ID1          0x8004  // MAC station ID1 register - upper 16 bits
#define F2_STA_ID1_SADH_MASK   0x0000FFFF // Mask for upper 16 bits of MAC addr
#define F2_STA_ID1_STA_AP      0x00010000 // Device is AP
#define F2_STA_ID1_AD_HOC      0x00020000 // Device is ad-hoc
#define F2_STA_ID1_PWR_SAV     0x00040000 // Power save reporting in self-generated frames
#define F2_STA_ID1_KSRCHDIS    0x00080000 // Key search disable
#define F2_STA_ID1_PSPOLLDIS   0x00100000 // Automatic PS poll disable
#define F2_STA_ID1_PCF         0x00200000 // Observe PCF
#define F2_STA_ID1_DESC_ANT    0x00400000 // Descriptor selects antenna
#define F2_STA_ID1_DEFAULT_ANT 0x00800000 // Toggles the antenna setting
#define F2_STA_ID1_ACKCTS_6MB  0x01000000 // Use 6Mb/s rate for ACK & CTS

#define F2_BSS_ID0          0x8008  // MAC BSSID low 32 bits
#define F2_BSS_ID1          0x800C  // MAC BSSID upper 16 bits / AID
#define F2_BSS_ID1_U16_M     0x0000FFFF // Mask for upper 16 bits of BSSID
#define F2_BSS_ID1_AID_M     0xFFFF0000 // Mask for association ID 
#define F2_BSS_ID1_AID_S     16         // Shift for association ID 

#define F2_SLOT_TIME        0x8010  // MAC Time-out after a collision
#define F2_SLOT_TIME_MASK    0x000007FF // Slot time mask

#define F2_TIME_OUT         0x8014  // MAC ACK & CTS time-out
#define F2_TIME_OUT_ACK_M    0x00001FFF // Mask for ACK time-out
#define F2_TIME_OUT_CTS_M    0x1FFF0000 // Mask for CTS time-out
#define F2_TIME_OUT_CTS_S    16         // Shift for CTS time-out

#define F2_RSSI_THR         0x8018  // MAC Beacon RSSI warning and missed beacon threshold
#define F2_RSSI_THR_MASK     0x000000FF // Mask for Beacon RSSI warning threshold
#define F2_RSSI_THR_BM_THR_M 0x00000700 // Mask for Missed beacon threshold
#define F2_RSSI_THR_BM_THR_S 8          // Shift for Missed beacon threshold

#define F2_RETRY_LMT        0x801c  // MAC Retry limits
#define F2_RETRY_LMT_SH_M    0x0000000F // Mask for short frame retry limit
#define F2_RETRY_LMT_LG_M    0x000000F0 // Mask for long frame retry limit
#define F2_RETRY_LMT_LG_S    4          // Shift for long frame retry limit
#define F2_RETRY_LMT_SSH_M   0x00003F00 // Mask for short station retry limit
#define F2_RETRY_LMT_SSH_S   8          // Shift for short station retry limit
#define F2_RETRY_LMT_SLG_M   0x000FC000 // Mask for long station retry limit
#define F2_RETRY_LMT_SLG_S   14         // Shift for long station retry limit
#define F2_RETRY_LMT_CW_M    0x3FF00000 // Mask for minimum contention window
#define F2_RETRY_LMT_CW_S    20         // Shift for minimum contention window

#define F2_USEC             0x8020  // MAC transmit latency register
#define F2_USEC_M            0x0000007F // Mask for clock cycles in 1 usec
#define F2_USEC_32_M         0x00003F80 // Mask for number of 32MHz clock cycles in 1 usec
#define F2_USEC_32_S         7          // Shift for number of 32MHz clock cycles in 1 usec
#define F2_USEC_TX_LAT_M     0x000FC000 // Mask for tx latency to start of SIGNAL (usec)
#define F2_USEC_TX_LAT_S     14         // Shift for tx latency to start of SIGNAL (usec)
#define F2_USEC_RX_LAT_M     0x03F00000 // Mask for rx latency to start of SIGNAL (usec)
#define F2_USEC_RX_LAT_S     20         // Shift for rx latency to start of SIGNAL (usec)

#define F2_BEACON           0x8024  // MAC beacon control value/mode bits
#define F2_BEACON_PERIOD_MASK 0x0000FFFF  // Beacon period mask in TU/msec
#define F2_BEACON_TIM_MASK    0x007F0000  // Mask for byte offset of TIM start
#define F2_BEACON_TIM_S       16          // Shift for byte offset of TIM start
#define F2_BEACON_EN          0x00800000  // beacon enable
#define F2_BEACON_RESET_TSF   0x01000000  // Clears TSF to 0

#define F2_CFP_PERIOD       0x8028  // MAC CFP Interval (TU/msec)
#define F2_TIMER0           0x802c  // MAC Next beacon time (TU/msec)
#define F2_TIMER1           0x8030  // MAC DMA beacon alert time (1/8 TU)
#define F2_TIMER2           0x8034  // MAC Software beacon alert (1/8 TU)
#define F2_TIMER3           0x8038  // MAC ATIM window time

#define F2_IFS0             0x8040  // MAC IFS 0 timers
#define F2_IFS0_SIFS_M       0x000007FF  // SIFS in core clock cycles
#define F2_IFS0_DIFS_M       0x007FF800  // Mask for DIFS in core clock cycles
#define F2_IFS0_DIFS_S       11          // Shift for DIFS in core clock cycles

#define F2_IFS1             0x8044  // MAC IFS 1 timers
#define F2_IFS1_PIFS_M       0x00000FFF  // PIFS in core clock cycles
#define F2_IFS1_EIFS_M       0x03FFF000  // Mask for EIFS in core clock cycles
#define F2_IFS1_EIFS_S       12          // Shift for EIFS in core clock cycles
#define F2_IFS1_CS_EN        0x04000000  // Carrier sense enable

#define F2_CFP_DUR          0x8048  // MAC maximum CFP duration in TU

#define F2_RX_FILTER        0x804C  // MAC receive filter register
#define F2_RX_FILTER_ALL     0x00000000 // Disallow all frames
#define F2_RX_UCAST          0x00000001 // Allow unicast frames
#define F2_RX_MCAST          0x00000002 // Allow multicast frames
#define F2_RX_BCAST          0x00000004 // Allow broadcast frames
#define F2_RX_CONTROL        0x00000008 // Allow control frames
#define F2_RX_BEACON         0x00000010 // Allow beacon frames
#define F2_RX_PROM           0x00000020 // Promiscuous mode, all packets

#define F2_MCAST_FIL0       0x8050  // MAC multicast filter lower 32 bits
#define F2_MCAST_FIL1       0x8054  // MAC multicast filter upper 32 bits
#define F2_TX_MASK0         0x8058  // MAC tx block mask lower 32 bits
#define F2_TX_MASK1         0x805c  // MAC tx block mask upper 32 bits
#define F2_CLR_TMASK        0x8060  // MAC tx block filter mask clear
#define F2_TRIG_LEV         0x8064  // MAC transmit FIFO threshold-fill before tx

#define F2_DIAG_SW          0x8068  // MAC PCU control register
#define F2_DIAG_CACHE_ACK    0x00000001 // disable ACK when no valid key found
#define F2_DIAG_ACK_DIS      0x00000002 // disable ACK generation
#define F2_DIAG_CTS_DIS      0x00000004 // disable CTS generation
#define F2_DIAG_ENCRYPT_DIS  0x00000008 // disable encryption
#define F2_DIAG_DECRYPT_DIS  0x00000010 // disable decryption
#define F2_DIAG_TX_DIS       0x00000020 // disable transmit
#define F2_DIAG_RX_DIS       0x00000040 // disable receive
#define F2_DIAG_LOOP_EN      0x00000080 // enable tx-rx loopback
#define F2_DIAG_CORR_FCS     0x00000100 // corrupt FCS
#define F2_DIAG_CHAN_INFO    0x00000200 // dump channel info
#define F2_DIAG_EN_SCRAMSD   0x00000400 // enable fixed scrambler seed
#define F2_DIAG_SCRAM_SEED_M 0x0003F800 // Mask for fixed scrambler seed
#define F2_DIAG_SCRAM_SEED_S 11         // Shift for fixed scrambler seed
#define F2_DIAG_DIS_SEQ_INC  0x00040000 // freeze sequence number increment
#define F2_DIAG_FRAME_NV0    0x00080000 // accept frames of non-zero protocol version

#define F2_TSF_L32          0x806c  // MAC local clock lower 32 bits
#define F2_TSF_U32          0x8070  // MAC local clock upper 32 bits
#define F2_LAST_TSTP        0x8080  // MAC Time stamp of the last beacon received
#define F2_RETRY_CNT        0x8084  // MAC current short and long retry counts
#define F2_RETRY_CNT_SSH_M   0x0000003F // Mask for Current station short retry count
#define F2_RETRY_CNT_SLG_M   0x00000FC0 // Mask for Current station long retry count
#define F2_RETRY_CNT_SLG_S   6          // Shift for Current station long retry count

#define F2_BACKOFF          0x8088  // MAC contention window size and back-off count
#define F2_BACKOFF_CW_M      0x000003FF // Current contention window size
#define F2_BACKOFF_CNT_M     0x03FF0000 // Mask for Back-off count
#define F2_BACKOFF_CNT_S     16         // Shift for Back-off count

#define F2_NAV              0x808c  // MAC current NAV value
#define F2_RTS_OK           0x8090  // MAC RTS exchange success counter
#define F2_RTS_FAIL         0x8094  // MAC RTS exchange failure counter
#define F2_ACK_FAIL         0x8098  // MAC ACK failure counter
#define F2_FCS_FAIL         0x809C  // FCS check failure counter
#define F2_BEACON_CNT       0x80A0  // Valid beacon counter

//
// Key table is 64 entries of 8 double-words each
//
#ifndef SWIG // SWIG cannot parse structures
#define D2_KEY_TABLE		0x9000
#define D2_KEY_NUM_ENTRIES	64
typedef struct D2KeyTableEntry
{
	A_UINT32	KeyVal0;
	A_UINT32	KeyVal1;
	A_UINT32	KeyVal2;
	A_UINT32	KeyVal3;
	A_UINT32	KeyVal4;
	A_UINT32	KeyType;
	A_UINT32	MacAddrLo;
	A_UINT32	MacAddrHi;
} D2_KEY_TABLE_ENTRY;

#ifdef ARCH_BIG_ENDIAN
typedef struct 
{
	A_UINT32	Reserved4:16,
				KeyValid:1,
				MacAddrHi:15;
} MAC_ADDR_HI_KEY_VALID;
#else
typedef struct 
{
	A_UINT32	MacAddrHi:15,
				KeyValid:1,
				Reserved4:16;
} MAC_ADDR_HI_KEY_VALID;
#endif /* ARCH_BIG_ENDIAN */
#endif // #ifndef SWIG

// PHY registers
#define PHY_BASE            0x9800  // PHY registers base address

#define PHY_FRAME_CONTROL   0x9804  // PHY frame control register
#define PHY_FC_TURBO_MODE    0x00000001 // Set turbo mode bits
#define PHY_FC_TURBO_SHORT   0x00000002 // Set short symbols to turbo mode setting
#define PHY_FC_TIMING_ERR    0x01000000 // Detect PHY timing error
#define PHY_FC_PARITY_ERR    0x02000000 // Detect PHY signal parity error
#define PHY_FC_ILLRATE_ERR   0x04000000 // Detect PHY illegal rate error
#define PHY_FC_ILLLEN_ERR    0x08000000 // Detect PHY illegal length error
#define PHY_FC_SERVICE_ERR   0x20000000 // Detect PHY non-zero service bytes error
#define PHY_FC_TX_UNDER_ERR  0x40000000 // Detect PHY transmit underrun error

#define PHY_CHIP_ID         0x9818  // PHY chip revision ID

#define PHY_ACTIVE          0x981C  // PHY activation register
#define PHY_ACTIVE_EN        0x00000001 // Activate PHY chips
#define PHY_ACTIVE_DIS       0x00000000 // Deactivate PHY chips

#define PHY_AGC_CONTROL     0x9860  // PHY chip calibration and noise floor setting
#define PHY_AGC_CONTROL_CAL  0x00000001 // Perform PHY chip internal calibration
#define PHY_AGC_CONTROL_NF   0x00000002 // Perform PHY chip noise-floor calculation

// Device ID defines for AR5210 devices
#define DEV_E2_PCI          0x0101 
#define DEV_E5_PCI          0x0102
#define DEV_E7_PCI          0x0103
#define DEV_E7_PCI_PA       0x0104
#define DEV_E7_PC_PA        0x0004
#define DEV_E9_PCI_PA       0x0105
#define DEV_E9_PC_PA        0x0005
#define DEV_E9_PC_ANT       0x0006
#define DEV_AR5210_PCI      0x0107
#define DEV_AR5210_PC       0x0007
#define DEV_AR5210_AP       0x0207
#define DEV_AR5001          0x0010
#define DEV_AR5001_QMAC     0x0011
#define DEV_AR5001_QMAC_FPGA 0xf011
#define DEV_LEGACY          0x1107


#endif