?? dw16550reg.h
字號:
///////////////////////////////////////////////////////////////////////////////
// UART register and field definitions
///////////////////////////////////////////////////////////////////////////////
#define UART_RBR 0x0 // Receive buffer register
#define UART_THR 0x0 // Transmit Holding Register
#define UART_DLL 0x0 // Divisor latch low register
#define UART_IER 0x4 // Interrupt Enable Register
#define UART_DLH 0x4 // Divisor latch high register
#define UART_IIR 0x8 // Interrupt identify register
#define UART_FCR 0x8 // FIFO control register
#define UART_FCR_FIFO_EN _SET_ONE_(0) // FIFO enable
#define UART_FCR_RX_FIFO_RST _SET_ONE_(1) // Rx FIFO RST
#define UART_FCR_TX_FIFO_RST _SET_ONE_(2) // Tx FIFO RST
#define UART_FCR_DMA_MODE _SET_ONE_(3) // DMA mode
#define UART_FCR_TX_EMPTY_TRIG_S 4
#define UART_FCR_TX_EMPTY_TRIG_W 2
#define UART_FCR_TX_EMPTY_TRIG_M _SET_ONES_(UART_FCR_TX_EMPTY_TRIG_S,UART_FCR_TX_EMPTY_TRIG_W)
#define UART_FCR_RX_EMPTY_TRIG_S 6
#define UART_FCR_RX_EMPTY_TRIG_W 2
#define UART_FCR_RX_EMPTY_TRIG_M _SET_ONES_(UART_FCR_RX_EMPTY_TRIG_S,UART_FCR_RX_EMPTY_TRIG_W)
#define UART_LCR 0xc // Line control Register
#define UART_LCR_NUMBITS_S 0 // bits per charecter
#define UART_LCR_NUMBITS_W 2
#define UART_LCR_NUMBITS_M _SET_ONES_(UART_LCR_NUMBITS_S,UART_LCR_NUMBITS_W)
#define UART_LCR_DLAB _SET_ONE_(7) // Divisor Latch Address Bit
#define UART_LCR_PE _SET_ONE_(3) // Parity Enable bit
#define UART_LCR_PS_EVEN _SET_ONE_(4) // Parity Select ( even or odd )
#define UART_MCR 0x10 // Modem control Register
#define UART_MCR_RTS _SET_ONE_(1)
#define UART_MCR_AUTO_FC_EN _SET_ONE_(5)
#define UART_LSR 0x14 // Line Status Register
#define UART_LSR_DR _SET_ONE_(0) // Data ready bit
#define UART_LSR_OE _SET_ONE_(1) // Overrun error indication : clear on read
#define UART_LSR_PE _SET_ONE_(2) // Parity Error indication : clear on read
#define UART_LSR_FE _SET_ONE_(3) // Framing Error indication : clear on read
#define UART_LSR_BI _SET_ONE_(4) // Break Interrupt bit : clear on read
#define UART_LSR_THRE _SET_ONE_(5) // Transmit Holding Reg Empty
#define UART_LSR_TEMT _SET_ONE_(6) // Transmitter Empty
#define UART_LSR_FERR _SET_ONE_(7) // Error in Rx FIFO
#define UART_MSR 0x18 // Modem status Register
#define UART_MSR_CTS _SET_ONE_(4) // Status of CTS_N
// Griffin specific registers
#define UART_SCR 0x1c // Scratch Register
#define UART_CCR 0x100 // clock configuration register
#define UART_RC 0x104 // reset control register
#define UART_CTL 0x108 // control register
#define UART_ISR 0x10c // Interrupt status register
#define UART_IMR 0x110 // Interrupt mask register
#define UART_EX_IER 0x114 // interrupt enable register for external UART logic
#define UART_ETFSTS 0x118 // extended transmit FIFO status register
#define UART_ERFSTS 0x11c // extended receive FIFO status register
// Data access UART registers
#define UART_ETF_PUSH11 0x400 // byte extended transmit FIFO write access ( min)
#define UART_ETF_PUSH12 0x5fc // byte extended transmit FIFO write access ( max)
#define UART_ETF_POP11 0x600 // byte extended receive FIFO read access (min)
#define UART_ETF_POP12 0x7fc // byte extended receive FIFO read access (max)
#define UART_ETF_PUSH41 0x800 // word extended transmit FIFO write access ( min)
#define UART_ETF_PUSH42 0xbfc // word extended transmit FIFO write access ( max)
#define UART_ETF_POP41 0xc00 // word extended receive FIFO read access (min)
#define UART_ETF_POP42 0xffc // word extended receive FIFO read access (max)
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -