# calsetup file updated for eeprom version 3.3,  ART version 2.4# General InfoCOUNTRY_OR_DOMAIN_FLAG	      = 0;	# 1 indicates the code is a country code. 0=>regulatory domain codeWORLD_WIDE_ROAMING_FLAG	      = 0;	# 1 indicates a single SKU covering worldwide roamingCOUNTRY_OR_DOMAIN_CODE        = 0x000;	# 12-bit country or domain code for intended region-of-use (hex)    SUB_VENDOR_ID		      = 0x168C; # SubVendor ID in hexMACID_FILENAME		      = K:\ART\macid.txt;  # central macID fileCUSTOMER_DEBUG                = 1;	# not to be turned on in normal operation.SHOW_TIMING_REPORT	      = 1;      # show time taken by various testsATHEROS_LOGGING_SCHEME        = 1;	# Enable the Atheros specific label scheme			        # Instrumentation Info	        USE_INSTRUMENTS	              = 1;	# Select whether Instruments are Connected	              PM_MODEL	              = 1;	# 1 => HP 436A, 2 => Agilent E4416A, 3 => 4531SA_MODEL                      = 2;PM_GPIB_ADDR	              = 13;	# Power meter GPIB Address	 SA_GPIB_ADDR	              = 18;	# Spectrum analyzer GPIB Address  ATT_GPIB_ADDR	              = 8;	# Attenuator GPIB Address	 		              GOLDEN_IP_ADDR	              = 192.168.1.210;    # IP addr of the golden machine#GOLDEN_IP_ADDR	              = .;    # Use . if both DUT and GU are control by same machine			        # Calibration Setup Info        CASE_TEMPERATURE              = 45;	# Case temperature of the AR5111 on the DUT during calibration (int)GOLDEN_PPM	              = -3;	# Measured PPM of golden device (int)ATTEN_DUT_SA                  = 14;	# Attenuation at 5.5GHz between DUT and spectrum analyzer (double)ATTEN_FIXED_DUT_GOLDEN        = 20;   	# Fixed attenuation at 5.5GHz between DUT and GOLDEN (double)ATTEN_DUT_PM                  = 22;  	# Attenuation at 5.5GHz between DUT and power meter (double)11b_ATTEN_DUT_SA              = 13;	# Attenuation at 2.5GHz between DUT and spectrum analyzer (double)11b_ATTEN_FIXED_DUT_GOLDEN    = 19;   	# Fixed attenuation at 2.5GHz between DUT and GOLDEN (double)11b_ATTEN_DUT_PM              = 21;  	# Attenuation at 2.5GHz between DUT and power meter (double)# Test MarginsNUM_MASK_FAIL_POINTS	      = 20;     # Manufacturing margin for spectral mask testPER_PASS_LIMIT		      = 90;     # Minimum number of good packets in TX_PER tests to pass SEN_PASS_LIMIT		      = 90;     # Minimum number of good packets in RX_SEN tests to pass PPM_MAX_LIMIT		      = 15;	# Maximum permitted PPM, after correcting for GOLDEN_PPMPPM_MIN_LIMIT		      =-15;	# Minimum permitted PPM, after correcting for GOLDEN_PPMTARGET_POWER_TOLERANCE_UPPER  = 1;	# Tolerance in dB to allow for target power control   (double)TARGET_POWER_TOLERANCE_LOWER  = 1.5;	# Tolerance in dB to allow for target power control   (double)MAX_RETEST_NUM		      = 3;      # Maximum number of times a test is run. Set value >= 1# Calibration flags	        CAL_POWER                     = 1;	# Calibrate power levels for 11a/b/g for modes supportedUSE_11g_CAL_FOR_11b	      = 1;      # Use 11g calibration data for 11b cal.REPROGRAM_TARGET_POWER        = 0;	# Re-program target power. No power measurements doneDO_IQ_CAL		      = 0;	# Perform iq_cal mismatch calibration# Use the following FIXED_GAIN setting to disable auto FIXED_GAIN algorithm for 11a and 11g mode# You can force FIXED_GAIN to the value between 0 (lowest) and 8 (highest)# If you comment out the following two lines, ART program will find the best FG setting automatically# FIXED_GAIN setting for 11b is fixed at 4 (auto or manual)CAL_FIXED_GAIN	     	      = 6;      # fixed gain to use for 11a calibration measurements11g_CAL_FIXED_GAIN	      = 6;      # fixed gain to use for 11g calibration measurements11b_CAL_FIXED_GAIN	      = 6;      # fixed gain to use for 11b calibration measurements# Use the following default iq_cal coeffs if can't run the iq_cal for any reason. it is recommended to run the# iq_cal on each board for optimum results.I_COEFF_5G                    =  8;      # typical i_coeff in 11a modeQ_COEFF_5G                    = -1;      # typical q_coeff in 11a modeI_COEFF_2G                    =  4;      # typical i_coeff in 11g modeQ_COEFF_2G                    =  0;      # typical q_coeff in 11g mode#FTP Download specificationDO_FTP_DOWNLOAD = 0;			# Set to download AP image at end of calibrationFTP_HOSTNAME    = 10.10.12.206;		# server to FTP fromFTP_USERNAME    = mdk;			# User name for FTP loginFTP_PASSWORD    = atheros;		# password for FTP loginFTP_REMOTE_FILE = test\freedomart.sys;  # file that will be copied onto the APFTP_LOCAL_FILE  = APIMG1		# Name of the file on the AP.##########################################  calsetup specific to 11a mode  ##########################################GOLDEN_TX_POWER               = 10;  	# Desired output power from the GU for 11a RXSEN test (double)MAX_POWER_CAP                 = 18;     # Cap power measurements during calibrationFORCE_PIERS	              = 1;	# calibrate power only at channels in the FORCE_PIERS_LIST##FORCE_PIERS_LIST              = 5170, 5230, 5300, 5400, 5500, 5650, 5725, 5825; # a maximum of up to 10 piers.FORCE_PIERS_LIST              = 5180, 5320, 5300, 5240, 5745, 5785, 5825; # a maximum of up to 10 piers.READ_FROM_FILE	              = 0;	# skip 11a cal. read data from a file instead.RAW_DATA_FILENAME             = cal_AR5211_power.log;	     # read 11a data from this file# AUTO_PIERS :     When FORCE_PIERS is off, set the following three parameters #                  to allow ART to automatically find the turning points over the#                  desired range.#AUTO_PIER_START             = 5150;   # (default 4900 if not specified)#AUTO_PIER_STOP              = 5500;   # (default 5850 if not specified)#AUTO_PIER_STEP              = 30;     # (default 70 if not specified) keep between 10-100MHz			        			        # General test flagsTEST_32KHZ_SLEEP_CRYSTAL      = 1;      # Test for proper functioning of the 32KHz sleep crystal# 11a mode test flags	        TEST_TEMP_MARGIN	      = 0;	# Test for target power control across 0-85C at 11a test freqencies.TEST_OBW_MASK                 = 0;	# Test occupied bandwidth mask at 11a test frequenciesTEST_SPEC_MASK                = 0;      # Test spectral mask at 11a test frequencies TEST_TXPER                    = 0;      # Test Transmit Packet Error Rate at 11a test frequencies TEST_RXSEN                    = 0;	# Test Receive Sensitivity at 11a test frequencies TEST_TURBO_MODE               = 0;	# Test PER and RXSEN in the turbo mode at 11a test frequencies TEST_HALF_RATE_MODE	      = 0;	# Test PER and RXSEN in the half rate mode at 11a test frequencies TEST_TARGET_POWER             = 0;	# Test Target Power at 11a test frequencies TEST_THROUGHPUT               = 0;# 11a, 11b and 11g Test Channel Matrices : #	 Rules:#		1. upto 32 test frequencies for each mode.#		2. if flags are turned on above to perform the TEMP_MARGIN_TEST, spectral mask, TXPER,#		   RXSEN and target power tests for 11a/b/g modes, they #		   will be performed at the following test frequencies based upon the#		   values in the PER_TEST, MASK_TEST, TGT_PWR_TEST and TEMP_MARGIN_TEST columns.#		3. OBW_TEST can be specified ONLY for 11a mode.##BEGIN_11a_TEST_CHANNEL_MATRIX  #  test_frequencies    	PER/SEN	SEN	LO_RATE	LO_RATE	TURBO	HALF_RATE	MASK	OBW	TGT_PWR	TEMP_MARGIN	TEST	PASS#			TEST	TGT	SEN	SEN_TGT	PER/SEN	PER/SEN		TEST	TEST	TEST	TEST		T/P	THRESHOLD# UNII-1&2 (5.15-5.35GHz) test channels    5180		1	-68	0	-88	1	0		1       0	1111	1		1	28.0#    5200		1	-68	0	-88	0	0		1       0	1111	0		1	28.0#    5220		1	-68	0	-88	0	0		1       0	1111	0		1	28.0#    5240		1	-68	0	-88	0	0		1       0	1111	0		1	28.0#    5260		1	-68	0	-88	0	0		0       0	1111	1		1	28.0#    5280		1	-68	0	-88	0	0		1       0	1111	0		1	28.0#    5300		1	-68	0	-88	0	0		1       0	1111	0		1	28.0    5320		1	-68	0	-88	1	0		1       0	1111	1		1	28.0# FCC turbo (static) test channels#    5210		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5250		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5290		0	-68	0	-88	1	0		0       0	0000	0		1	28.0# Dynamic turbo test channels#    5200		0	-68	0	-88	1	0		0       0	0000	0		1	28.0    5240		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5280		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5765		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5805		0	-68	0	-88	1	0		0       0	0000	0		1	28.0# UNII-3 & ISM band test channels    5745		1	-68	0	-88	1	0		0       0	1111	1		1	28.0#    5765		1	-68	0	-88	0	0		0       0	1111	0		1	28.0    5785		0	-68	0	-88	1	0		0       0	0000	0		1	28.0#    5805		1	-68	0	-88	0	0		0       0	1111	0		1	28.0    5825		1	-68	0	-88	1	0		0       0	1111	1		1	28.0# ETSI (5.47-5.7GHz) test channels#    5500		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5520		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5540		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5560		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5580		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5600		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5620		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5640		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5660		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5680		1	-68	0	-88	0	0		0       0	1111	0		1	28.0#    5700		1	-68	0	-88	0	0		0       0	1111	0		1	28.0# MKK (5.15-5.25GHz) test channels#    5170		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5190		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5210		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5230		0	-68	0	-88	0	0		0       1	1111	0		1	28.0# MKK (4.9-5.1GHz) test channels#    4900		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    4920		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    4940		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    4960		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    4980		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5040		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5060		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#    5080		0	-68	0	-88	0	0		0       1	1111	0		1	28.0#END_11a_TEST_CHANNEL_MATRIX  ##########################################  calsetup specific to 11b mode  ##########################################11b_GOLDEN_TX_POWER           = 30; 	# Desired output power from the GU for 11b RXSEN test (double)11b_MAX_POWER_CAP             = 20;     # Cap power measurements during calibrationFORCE_PIERS_11b	              = 1;	# calibrate power only at channels in the FORCE_PIERS_LIST_11bFORCE_PIERS_LIST_11b          = 2417, 2442, 2462;	# a maximum of up to 3 piers. 11b_READ_FROM_FILE	      = 0;	# skip 11b cal. read data from a file instead.11b_RAW_DATA_FILENAME	      = cal_AR5211_power_11b.log;    # read 11b data from this file			        # 11b mode test flags	        11b_TEST_TEMP_MARGIN	      = 0;	# Test for target power control across 0-85C at 11b test freqencies.11b_TEST_SPEC_MASK            = 0;      # Test spectral mask at 11b test frequencies 11b_TEST_TXPER                = 0;      # Test Transmit Packet Error Rate at 11b test frequencies 11b_TEST_RXSEN                = 0;      # Test Receive Sensitivity at 11b test frequencies 11b_TEST_TARGET_POWER         = 0;      # Test Target Power at 11b test frequencies 11b_TEST_THROUGHPUT           = 0;#BEGIN_11b_TEST_CHANNEL_MATRIX  #  test_frequencies    	PER/SEN	SEN	LO_RATE	LO_RATE	MASK	TGT_PWR	TEMP_MARGIN	TEST	PASS#			TEST	TGT	SEN	SEN_TGT	TEST	TEST	TEST		T/P	THRESHOLD#   2412                  1	-85	0	 -90	0	1111	0		1	7.0   2417                  1	-85	0	 -90	1	1111	1		1	7.0#   2422                  1	-85	0	 -90	0	1111	0		1	7.0#   2427                  1	-85	0	 -90	0	1111	0		1	7.0#   2432                  1	-85	0	 -90	0	1111	0		1	7.0#   2437                  1	-85	0	 -90	0	1111	0		1	7.0   2442                  0	-85	0	 -90	1	1111	1		1	7.0#   2447                  1	-85	0	 -90	0	1111	0		1	7.0#   2452                  1	-85	0	 -90	0	1111	0		1	7.0#   2457                  1	-85	0	 -90	0	1111	0		1	7.0   2462                  1	-85	0	 -90	1	1111	1		1	7.0#   2467                  1	-85	0	 -90	0	1111	0		1	7.0#   2472                  1	-85	0	 -90	0	1111	0		1	7.0#   2484                  1	-85	0	 -90	0	1111	0		1	7.0#END_11b_TEST_CHANNEL_MATRIX  ##########################################  calsetup specific to 11g mode  ##########################################11g_GOLDEN_TX_POWER           = 10; 	# Desired output power from the GU for 11g RXSEN test (double)11g_MAX_POWER_CAP             = 20;     # Cap power measurements during calibrationFORCE_PIERS_11g	              = 1;	# calibrate power only at channels in the FORCE_PIERS_LIST#FORCE_PIERS_LIST_11g          = 2412 2442 2462 ;	# a maximum of up to 3 piers.FORCE_PIERS_LIST_11g          = 2412  ;	# a maximum of up to 3 piers.11g_READ_FROM_FILE	      = 0;	# skip 11g cal. read data from a file instead.11g_RAW_DATA_FILENAME	      = cal_AR5211_power_11g.log;    # read 11g data from this file			        	# 11g mode test flags	        	11g_TEST_TEMP_MARGIN	      = 0;	# Test for target power control across 0-85C at 11g test freqencies.11g_TEST_SPEC_MASK            = 1;      # Test spectral mask at 11g test frequencies 11g_TEST_TXPER	              = 1;      # Test Transmit Packet Error Rate at 11g test frequencies 11g_TEST_RXSEN	              = 1;      # Test Receive Sensitivity at 11g test frequencies 11g_TEST_TARGET_POWER         = 1;      # Test Target Power at 11g test frequencies 11g_TEST_TURBO_MODE	      = 0;      # Test PER and RXSEN in the turbo mode at 11g test frequencies 11g_TEST_DATA_INTEGRITY	      = 0;      # Test memory by performing data comparison for long packets 11g_TEST_THROUGHPUT           = 0;#BEGIN_11g_TEST_CHANNEL_MATRIX  #  test_frequencies    	PER/SEN	SEN	LO_RATE	LO_RATE  TURBO	  MASK	TGT_PWR	TEMP_MARGIN	TEST	PASS#			TEST	TGT	SEN	SEN_TGT  PER/SEN  TEST	TEST	TEST		T/P	THRESHOLD						         	  						   2412                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2417                  1	-68	0	 -88     1	  1	1111	1		1	28.0#   2422                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2427                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2432                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2437                  1	-68	0	 -88     0	  1	1111	0		1	28.0 #  2442                  0	-68	0	 -88     1	  1	1111	1		1	28.0#   2447                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2452                  1	-68	0	 -88     0	  0	1111	0		1	28.0#   2457                  1	-68	0	 -88	 0	  0	1111	0		1	28.0 #  2462                  1	-68	0	 -88	 1	  1	1111	1		1	28.0#   2467                  1	-68	0	 -88	 0	  0	1111	0		1	28.0#   2472                  1	-68	0	 -88	 0	  0	1111	0		1	28.0#   2484                  1	-68	0	 -88	 0	  0	1111	0		1	28.0#END_11g_TEST_CHANNEL_MATRIX