?? 2410library.c
字號:
#include "2410library.h"
#include "2410slibrary.h"
#include "2410addr.h"
#include <stdio.h>
#include <stdarg.h>
#include <string.h>
#include <stdlib.h>
#include <ctype.h>
//===========================[ SYSTEM ]===================================================
//static int delayLoopCount = 400;
static int delayLoopCount = FCLK/10000/10;
void Delay(int time)
{
// time=0: adjust the Delay function by WatchDog timer.
// time>0: the number of loop time
// resolution of time is 100us.
int i,adjust=0;
if(time==0)
{
time = 200;
adjust = 1;
delayLoopCount = 400;
//PCLK/1M,Watch-dog disable,1/64,interrupt disable,reset disable
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3);
rWTDAT = 0xffff; //for first update
rWTCNT = 0xffff; //resolution=64us @any PCLK
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3)|(1<<5); //Watch-dog timer start
}
for(;time>0;time--)
for(i=0;i<delayLoopCount;i++);
if(adjust==1)
{
rWTCON = ((PCLK/1000000-1)<<8)|(2<<3); //Watch-dog timer stop
i = 0xffff - rWTCNT; //1count->64us, 200*400 cycle runtime = 64*i us
delayLoopCount = 8000000/(i*64); //200*400:64*i=1*x:100 -> x=80000*100/(64*i)
}
}
/********************************************************************
// Function name : Led_Display
// Description : 顯示LED燈
// Return type : void
// Argument : int data (1 - on, 0 - off)
// 3 2 1 0
// LED4 LED3 LED2 LED1
*********************************************************************/
unsigned char output_0x10000000 = 0xff;
void Led_Display(int data)
{
output_0x10000000 &= (~0xf0);
output_0x10000000 |= (((~data)<< 4) & 0xf0);
*((unsigned char *)0x10000000) = output_0x10000000;
}
/********************************************************************
// Function name : Seg7_Display
// Description : 數碼管顯示程序
// Return type : void
// Argument : unsigned char mask : 數碼管顯示掩碼 bit0 - bit5 : SEG0 - SEG5
// Argument : unsigned char * pdata : 數碼管對應數據 bit0 - bit5 : SEG0 - SEG5
*********************************************************************/
unsigned char seg7table[16] =
{
/* 0 1 2 3 4 5 6 7*/
0xc0, 0xf9, 0xa4, 0xb0, 0x99, 0x92, 0x82, 0xf8,
/* 8 9 A B C D E F*/
0x80, 0x90, 0x88, 0x83, 0xc6, 0xa1, 0x86, 0x8e,
};
void Seg7_Display(unsigned char mask, unsigned char * pdata)
{
int i = 0;
for(i = 0; i < 6; i++)
{
if(mask & (1 << i))
{
*((unsigned char *)0x10000006) = ~(1 << i) & 0x3f;
*((unsigned char *)0x10000004) = seg7table[(pdata[i]) & 0xf];
Delay(40);
}
}
}
/****************************************************************************/
/* Function name : 循環延時子程序 */
/* Description : 循環 'time' 次 */
/* Return type ：void */
/* Argument : 循環延時計數器 */
/****************************************************************************/
void Delay_ms(int time)
{
int i;
int delayLoopCount=1000;
for(;time>0;time--);
for(i=0;i<delayLoopCount;i++);
}
/********************************************************************
// Function name : ChangeMPllValue
// Description : 設置MPLL值
// Return type : void
// Argument : int mdiv
// Argument : int pdiv
// Argument : int sdiv
*********************************************************************/
void ChangeMPllValue(int mdiv,int pdiv,int sdiv)
{
rMPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
}
/********************************************************************
// Function name : ChangeClockDivider
// Description : 配置HCLK和PCLK
// Return type : void
// Argument : int hdivn
// Argument : int pdivn
*********************************************************************/
void ChangeClockDivider(int hdivn,int pdivn)
{
// hdivn,pdivn FCLK:HCLK:PCLK
// 0,0 1:1:1
// 0,1 1:1:2
// 1,0 1:2:2
// 1,1 1:2:4
rCLKDIVN = (hdivn<<1) | pdivn;
if(hdivn)
MMU_SetAsyncBusMode();
else
MMU_SetFastBusMode();
}
//===========================[ PORTS ]===================================================*
/********************************************************************
// Function name : Port_Init
// Description : JXARM9-2410端口初始化
// Return type : void
// Argument : void
*********************************************************************/
void Port_Init(void)
{
//CAUTION:Follow the configuration order for setting the ports.
// 1) setting value(GPnDAT)
// 2) setting control register (GPnCON)
// 3) configure pull-up resistor(GPnUP)
//32bit data bus configuration
//=== PORT A GROUP
//Ports : GPA22 GPA21 GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12
//Signal : nFCE nRSTOUT nFRE nFWE ALE CLE nGCS5 nGCS4 nGCS3 nGCS2 nGCS1
//Binary : 1 1 1 , 1 1 1 1 , 1 1 1 1
//Ports : GPA11 GPA10 GPA9 GPA8 GPA7 GPA6 GPA5 GPA4 GPA3 GPA2 GPA1 GPA0
//Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0
//Binary : 1 1 1 1 , 1 1 1 1 , 1 1 1 1
rGPACON = 0x7fffff;
//===* PORT B GROUP
//Ports : GPB10 GPB9 GPB8 GPB7 GPB6 GPB5 GPB4 GPB3 GPB2 GPB1 GPB0
//Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard
//Setting: INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
//Binary : 00 , 01 00 , 01 00 , 01 01 , 01 01 , 01 01
rGPBCON = 0x044555;
rGPBUP = 0x7ff; // The pull up function is disabled GPB[10:0]
//=== PORT C GROUP
//Ports : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8 GPC7 GPC6 GPC5 GPC4 GPC3 GPC2 GPC1 GPC0
//Signal : VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10
rGPCCON = 0xaaaaaaaa;
rGPCUP = 0xffff; // The pull up function is disabled GPC[15:0]
//=== PORT D GROUP
//Ports : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0
//Signal : VD23 VD22 VD21 VD20 VD19 VD18 VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9 VD8
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,10 10
rGPDCON = 0xaaaaaaaa;
rGPDUP = 0xffff; // The pull up function is disabled GPD[15:0]
//=== PORT E GROUP
//Ports : GPE15 GPE14 GPE13 GPE12 GPE11 GPE10 GPE9 GPE8 GPE7 GPE6 GPE5 GPE4
//Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO
//Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,
//-------------------------------------------------------------------------------------------------------
//Ports : GPE3 GPE2 GPE1 GPE0
//Signal : I2SSDI CDCLK I2SSCLK I2SLRCK
//Binary : 10 10 , 10 10
rGPECON = 0xaaaaaaaa;
rGPEUP = 0xffff; // The pull up function is disabled GPE[15:0]
//=== PORT F GROUP
//Ports : GPF7 GPF6 GPF5 GPF4 GPF3 GPF2 GPF1 GPF0
//Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0
//Setting: Output Output Output Output EINT3 EINT2 EINT1 EINT0
//Binary : 01 01 , 01 01 , 10 10 , 10 10
rGPFCON = 0x55aa;
rGPFUP = 0xff; // The pull up function is disabled GPF[7:0]
#if 0 // LIUSJ, Commented for AIJI
//*** PORT G GROUP
//Ports : GPG15 GPG14 GPG13 GPG12 GPG11 GPG10 GPG9 GPG8 GPG7 GPG6
//Signal : nYPON YMON nXPON XMON EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI
//Setting: nYPON YMON nXPON XMON EINT19 Output Output Output SPICLK1 SPIMOSI1
//Binary : 11 11 , 11 11 , 10 01 , 01 01 , 11 11
//-----------------------------------------------------------------------------------------
//Ports : GPG5 GPG4 GPG3 GPG2 GPG1 GPG0
//Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA
//Setting: SPIMISO1 LCD_PWRDN EINT11 nSS0 EINT9 EINT8
//Binary : 11 11 , 10 11 , 10 10
rGPGCON = 0xff95ffba;
rGPGUP = 0xffff; // The pull up function is disabled GPG[15:0]
#else
//config GPG15-12 to Touch Panel signals
//config GPG11-10 to output pins
//config GPG9-8 to output pins
//config GPG7-5 to output pins ----Testpoints:TP6,4,2
//config GPG4 to LCD Power Enable
//config GPG3-2 to output pins ----Testpints:TP8,7
//config GPG1-0 to output pins ----GPRS_boot and GPRS_PWR
rGPGCON = 0xff055555;
rGPGUP = 0xfffff;
#endif
/*
//GPG4 Output Port [9:8] 01 -> LCD_PWREN Enable
rGPGCON = (rGPGCON & 0xfffffcff) | (1<<8);
rGPGDAT = (rGPGDAT & 0xffef) | (1<<4);
*/
//=== PORT H GROUP
//Ports : GPH10 GPH9 GPH8 GPH7 GPH6 GPH5 GPH4 GPH3 GPH2 GPH1 GPH0
//Signal : CLKOUT1 CLKOUT0 UCLK nCTS1 nRTS1 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0
//Binary : 10 , 10 10 , 11 11 , 10 10 , 10 10 , 10 10
rGPHCON = 0x2afaaa;
rGPHUP = 0x7ff; // The pull up function is disabled GPH[10:0]
//External interrupt will be falling edge triggered.
rEXTINT0 = 0x22222222; // EINT[7:0]
rEXTINT1 = 0x22222222; // EINT[15:8]
rEXTINT2 = 0x22222222; // EINT[23:16]
}
/* 當前UART號：0-UART0, 1-UART1, 2-UART2 */
static int whichUart=0;
/********************************************************************
// Function name : Uart_Init
// Description : JXARM9-2410串口初始化
// Return type : void
// Argument : int pclk:APB總線時鐘，0時使用缺省值PCLK
// Argument : int baud:波特率
*********************************************************************/
void Uart_Init(int pclk,int baud)
{
int i;
if(pclk == 0)
pclk = PCLK;
rUFCON0 = 0x0; //UART channel 0 FIFO control register, FIFO disable
rUFCON1 = 0x0; //UART channel 1 FIFO control register, FIFO disable
rUFCON2 = 0x0; //UART channel 2 FIFO control register, FIFO disable
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -