/* config.h - MagicARM2410   configuration header *//*modification history--------------------*//*This module contains the configuration parameters for the MagicARM2410  BSP.*/#ifndef	INCconfigh#define	INCconfigh#ifdef __cplusplusextern "C" {#endif/* BSP version/revision identification, before configAll.h */#define BSP_VER_1_1     1       /* 1.2 is backwards compatible with 1.1 */#define BSP_VER_1_2     1#define BSP_VERSION	"1.0"#define BSP_REV		  "/1"	        /* 0 for first revision */#include "configAll.h"#define DBG_BSP#define FORCE_DEFAULT_BOOT_LINE#ifdef  FORCE_DEFAULT_BOOT_LINE#undef  INCLUDE_VWARE_LAUNCH#else#define INCLUDE_VWARE_LAUNCH#endif /* FORCE_DEFAULT_BOOT_LINE */#define DEFAULT_BOOT_LINE 		  "dmf(0,0)host:vxWorks " \                                "h=192.168.18.5 " \                                "e=192.168.18.18:ffffff00 " \                                "g=192.168.18.1 "  \                                "u=magic "     \                                "pw=magic "     \                                "tn=vxWorks " \                                "o=dmf"#define BYTE_ORDER 	_LITTLE_ENDIAN/* Memory configuration */#undef	LOCAL_MEM_AUTOSIZE			/* run-time memory sizing */#define USER_RESERVED_MEM	  0		/* see sysMemTop() *//* * Local-to-Bus memory address constants: * the local memory address always appears at 0 locally; * it is not dual ported. */#define LOCAL_MEM_LOCAL_ADRS	0x30000000		        /* fixed at 0x30000000 */#define LOCAL_MEM_BUS_ADRS	  LOCAL_MEM_LOCAL_ADRS	/* fixed at 0x30000000 */#define LOCAL_MEM_SIZE		    0x04000000		        /* 64 Mbytes */#define LOCAL_MEM_END_ADRS	  (LOCAL_MEM_LOCAL_ADRS + LOCAL_MEM_SIZE)/* * Boot ROM is an image written into Flash. Part of the Flash can be * reserved for boot parameters etc. (see the Flash section below). * * The following parameters are defined here and in the Makefile. * They must be kept synchronized; effectively config.h depends on Makefile. * Any changes made here must be made in the Makefile and vice versa. * * ROM_BASE_ADRS is the base of the Flash ROM/EPROM. * ROM_TEXT_ADRS is the entry point of the VxWorks image * ROM_SIZE is the size of the part of the Flash ROM/EPROM allocated to *		the VxWorks image (block size - size of headers) * * Two other constants are used: * ROM_COPY_SIZE is the size of the part of the ROM to be copied into RAM * 		 (e.g. in uncompressed boot ROM) * ROM_SIZE_TOTAL is the size of the entire Flash ROM (used in sysPhysMemDesc) * * The values are given as literals here to make it easier to ensure * that they are the same as those in the Makefile. */#define ROM_BASE_ADRS	0x00000000	  /* base of Flash/EPROM */#define ROM_TEXT_ADRS	ROM_BASE_ADRS	/* code start addr in ROM */#define ROM_WARM_ADRS	0x00000004	  /* code start addr in ROM */#define ROM_SIZE	    0x00100000	  /*size of ROM holding VxWorks*/#define ROM_COPY_SIZE	  ROM_SIZE#define ROM_SIZE_TOTAL	0x00200000	/* total size of ROM */#define RAM_LOW_ADRS	0x30010000	  /* VxWorks image entry point */#define RAM_HIGH_ADRS	0x33000000	  /* RAM address for ROM boot */#define ROM_MAC_ADRS  0x00040000#undef  VEC_BASE_ADRS           /*Add  abnormity vector  */#define VEC_BASE_ADRS   0x30000000/* * Count for a CPU delay loop at the beginning of romInit. There have been * reports of problems with certain boards and certain power supplies, and * adding a delay at the start of romInit appears to help with this. This * value may need tuning for different board/PSU combinations. */#define ____BOOT_DELAY_VALUE	0x1000/* * Flash/NVRAM memory configuration * * A block of the Flash memory (FLASH_SIZE bytes at FLASH_ADRS) is * reserved for non-volatile storage of data. * * See also integrator.h */#undef   INCLUDE_FLASH#define  NV_RAM_SIZE           NONE/* Serial port configuration */#undef   INCLUDE_TYCODRV_5_2#define  INCLUDE_SERIAL#undef	 NUM_TTY#undef   CONSOLE_TTY#undef   CONSOLE_BAUD_RATE#define  NUM_TTY			N_SIO_CHANNELS#define  CONSOLE_TTY		0	             /* console channel */#define  CONSOLE_BAUD_RATE	115200	   /* console baud rate *//* * Cache/MMU configuration * * Note that when MMU is enabled, cache modes are controlled by * the MMU table entries in sysPhysMemDesc[], not the cache mode * macros defined here. */ /* * Include MMU BASIC and CACHE support for command line and project builds */#define	INCLUDE_MMU#define	INCLUDE_MMU_BASIC#define INCLUDE_CACHE_SUPPORT/* * We use the generic architecture libraries, with caches/MMUs present. A * call to sysHwInit0() is needed from within usrInit before * cacheLibInit() is called. */#ifndef _ASMLANGUAGE     IMPORT void sysHwInit0 (void);#endif#define INCLUDE_SYS_HW_INIT_0#define SYS_HW_INIT_0()         sysHwInit0()/* * I-cache mode is a bit of an inappropriate concept, but use this. */#undef  USER_I_CACHE_MODE#define USER_I_CACHE_MODE       CACHE_WRITETHROUGH/* has to be this. */#undef  USER_D_CACHE_MODE#define USER_D_CACHE_MODE       CACHE_COPYBACK/* Enhanced Network Driver (END) Support */#ifndef INCLUDE_END#define INCLUDE_END#define INCLUDE_FTP_SERVER#endif/* * Network driver configuration. * * De-select unused (default) network drivers selected in configAll.h. */#define INCLUDE_NETWORK/*#undef  INCLUDE_NETWORK*//*#undef  INCLUDE_END*/#undef  STANDALONE_NET#undef	INCLUDE_EI#undef	INCLUDE_EX		        #undef	INCLUDE_ENP		        #undef	INCLUDE_SM_NET		   #undef  INCLUDE_LN#undef	INCLUDE_SM_SEQ_ADDR	 /* Enhanced Network Driver (END) Support */#undef  INCLUDE_LED#ifdef  INCLUDE_LED#define INCLUDE_LED#endif/* WDB configuration. */#define INCLUDE_NETWORK#define INCLUDE_WDB#undef  WDB_COMM_TYPE#define WDB_COMM_TYPE	WDB_COMM_END  #undef  SYS_CLK_RATE#define SYS_CLK_RATE		100/* * Interrupt mode - interrupts can be in either preemptive or non-preemptive * mode.  For non-preemptive mode, change INT_MODE to INT_NON_PREEMPT_MODEL */#define INT_MODE	INT_PREEMPT_MODEL/* * Enable BSP-configurable interrupt priorities: order of servicing and * masking of interrupts will be determined by ambaIntLvlPriMap[] in * sysLib.c.  If AMBA_INT_PRIORITY_MAP is not defined, priority of * interrupts will be least-significant bit first. *//* * miscellaneous definitions * Note: ISR_STACK_SIZE is defined here rather than in ../all/configAll.h * (as is more usual) because the stack size depends on the interrupt * structure of the BSP. */#define ISR_STACK_SIZE	0x800	/* size of ISR stack, in bytes *//* Optional timestamp support */#undef	INCLUDE_TIMESTAMP	/* define to include timestamp driver *//*#define INCLUDE_TIMESTAMP*//*#define INCLUDE_RAMDRV Optional TrueFFS support */#undef  INCLUDE_TFFS      #ifdef  INCLUDE_TFFS#define INCLUDE_SHOW_ROUTINES#define INCLUDE_TFFS_SHOW#define INCLUDE_DOSFS#define INCLUDE_DISK_UTIL/*ADD BY supercontrol*/#define INCLUDE_TL_FTL#endif /* INCLUDE_TFFS */#include "s3c2410x.h"#undef BSP_VTS#ifdef BSP_VTS/*************************************************** * Add these defines for the Validation Test Suite * ***************************************************/#define INCLUDE_SHELL#undef INCLUDE_RLOGIN#undef INCLUDE_SHOW_ROUTINES#undef INCLUDE_NET_SYM_TBL#define INCLUDE_LOADER#undef INCLUDE_PING#undef INCLUDE_NET_SHOW#endif /*BSP_VTS*/#define INCLUDE_SHELL #ifdef  INCLUDE_SHELL#define INCLUDE_SYM_TABLE#define INCLUDE_STANDALONE_SYM_TABLE#define INCLUDE_LOADER#define INCLUDE_ELF#define INCLUDE_STARTUP_SCRIPT#define INCLUDE_UNLOADER/*#define INCLUDE_NET_SHOW*/#endif /* INCLUDE_SHELL */#undef INCLUDE_WINDML #ifdef __cplusplus}#endif#endif  /* INCconfigh */#if defined(PRJ_BUILD)#include "prjParams.h"#endif