?? ili932x.c
字號:
/******************************************************************************
* 文件名稱：ili932x.c
* 摘 要：支持ILI9320和ILI9325驅動IC控制的QVGA顯示屏，使用16位并行傳輸
到頭文件中配置 屏幕使用方向和驅動IC類型
注意：16位數據線色彩分布>> BGR(565)
* 當前版本：V1.3
* 修改說明：版本修訂說明：
1.修改翻轉模式下的ASCII字符寫B(tài)ug
2.增加可以在翻轉模式下的自動行寫
3.優化刷圖片 使用流水線方法提效率
*重要說明！
在.h文件中，#define Immediately時是立即顯示當前畫面
而如果#define Delay，則只有在執行了LCD_WR_REG(0x0007,0x0173);
之后才會顯示，執行一次LCD_WR_REG(0x0007,0x0173)后，所有寫入數
據都立即顯示。
#define Delay一般用在開機畫面的顯示，防止顯示出全屏圖像的刷新
過程
******************************************************************************/
#include "stm32f10x_lib.h"
#include "ili932x.h"
#include "HzLib_65k.h"
/****************************************************************
函數名：Lcd配置函數
功能：配置所有和Lcd相關的GPIO和時鐘
引腳分配為：
PB8--PB15——16Bit數據總線低8位
PC0--PC7 ——16Bit數據總線高8位
PC8 ——Lcd_cs
PC9 ——Lcd_rs*
PC10——Lcd_wr
PC11——Lcd_rd*
PC12——Lcd_rst
PC13——Lcd_blaklight 背光靠場效應管驅動背光模塊
*****************************************************************/
void Lcd_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
/*開啟相應時鐘 */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC, ENABLE);
/*所有Lcd引腳配置為推挽輸出*/
/*16位數據低8位*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
/*16位數據高8位*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
GPIO_Init(GPIOC, &GPIO_InitStructure);
/*控制腳*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12;
GPIO_Init(GPIOC, &GPIO_InitStructure);
/*背光控制*/
GPIO_InitStructure.GPIO_Pin =GPIO_Pin_13;
GPIO_Init(GPIOC, &GPIO_InitStructure);
}
void DataToWrite(u16 data)
{
u16 temp;
temp = GPIO_ReadOutputData(GPIOB);
GPIO_Write(GPIOB, (data<<8)|(temp&0x00ff));
temp = GPIO_ReadOutputData(GPIOC);
GPIO_Write(GPIOC, (data>>8)|(temp&0xff00));
}
/****************************************************************************
* 名 稱：u16 CheckController(void)
* 功 能：返回控制器代碼
* 入口參數：無
* 出口參數：控制器型號
* 說 明：調用后返回兼容型號的控制器型號
* 調用方法：code=CheckController();
****************************************************************************/
u16 CheckController(void)
{
u16 tmp=0,tmp1=0,tmp2=0;
GPIO_InitTypeDef GPIO_InitStructure;
DataToWrite(0xffff);//數據線全高
Set_Rst;
Set_nWr;
Set_Cs;
Set_Rs;
Set_nRd;
Set_Rst;
Delay_nms(1);
Clr_Rst;
Delay_nms(1);
Set_Rst;
Delay_nms(1);
LCD_WR_REG(0x0000,0x0001); //start oscillation
Delay_nms(1);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOB, &GPIO_InitStructure);
/*16位數據高8位*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_ResetBits(GPIOC,GPIO_Pin_8);
GPIO_SetBits(GPIOC,GPIO_Pin_9);
GPIO_ResetBits(GPIOC,GPIO_Pin_11);
tmp1 = GPIO_ReadInputData(GPIOB);
tmp2 = GPIO_ReadInputData(GPIOC);
tmp = (tmp1>>8) | (tmp2<<8);
GPIO_SetBits(GPIOC,GPIO_Pin_11);
GPIO_SetBits(GPIOC,GPIO_Pin_8);
/*16位數據低8位*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
/*16位數據高8位*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
GPIO_Init(GPIOC, &GPIO_InitStructure);
return tmp;
}
/**********************************************
函數名：Lcd初始化函數
功能：初始化Lcd
入口參數：無
返回值：無
***********************************************/
void Lcd_Initialize(void)
{
u16 i;
Lcd_Light_ON;
DataToWrite(0xffff);//數據線全高
Set_Rst;
Set_nWr;
Set_Cs;
Set_Rs;
Set_nRd;
Set_Rst;
Delay_nms(1);
Clr_Rst;
Delay_nms(1);
Set_Rst;
Delay_nms(1);
/*
#ifdef ILI9325
LCD_WR_REG(0x00e3,0x3008);
LCD_WR_REG(0x00e7,0x0010);
LCD_WR_REG(0x00ef,0x1231); //Set the internal vcore voltage
LCD_WR_REG(0x0001,0x0100); //When SS = 0, the shift direction of outputs is from S1 to S720
#endif //When SS = 1, the shift direction of outputs is from S720 to S1.
#ifdef ILI9320
LCD_WR_REG(0x00e5,0x8000);
LCD_WR_REG(0x0000,0x0001);
LCD_WR_REG(0x0001,0x0100);//S
Delay_nms(10);
#endif
LCD_WR_REG(0x0002,0x0700);//Line inversion
#if ID_AM==000
LCD_WR_REG(0x0003,0x0000);//屏幕旋轉控制 TFM=0,TRI=0,SWAP=1,16 bits system interface swap RGB to BRG，此處ORG和HWM 為0
#elif ID_AM==001
LCD_WR_REG(0x0003,0x0008);
#elif ID_AM==010
LCD_WR_REG(0x0003,0x0010);
#elif ID_AM==011
LCD_WR_REG(0x0003,0x0018);
#elif ID_AM==100
LCD_WR_REG(0x0003,0x0020);
#elif ID_AM==101
LCD_WR_REG(0x0003,0x0028);
#elif ID_AM==110
LCD_WR_REG(0x0003,0x0030);
#elif ID_AM==111
LCD_WR_REG(0x0003,0x0038);
#endif
LCD_WR_REG(0x0004,0x0000);
LCD_WR_REG(0x0008,0x0207);
LCD_WR_REG(0x0009,0x0000);
LCD_WR_REG(0x000a,0x0000);
LCD_WR_REG(0x000c,0x0001);//此處配置接口類型 16位 system接口
LCD_WR_REG(0x000d,0x0000);
LCD_WR_REG(0x000f,0x0000);
//電源配置
LCD_WR_REG(0x0010,0x0000);
LCD_WR_REG(0x0011,0x0000);
LCD_WR_REG(0x0012,0x0000);
LCD_WR_REG(0x0013,0x0000);
Delay_nms(200);
LCD_WR_REG(0x0010,0x17b0);
LCD_WR_REG(0x0011,0x0137);
Delay_nms(50);
LCD_WR_REG(0x0012,0x0139);
Delay_nms(50);
LCD_WR_REG(0x0013,0x1700);
LCD_WR_REG(0x0029,0x0000);
LCD_WR_REG(0x002b,0x0000);
Delay_nms(50);
#if ID_AM==000
LCD_WR_REG(0x0020,0x00ef);//GRAM水平起始位置
LCD_WR_REG(0x0021,0x013f);
#elif ID_AM==001
LCD_WR_REG(0x0020,0x00ef);
LCD_WR_REG(0x0021,0x013f);
#elif ID_AM==010
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x013f);
#elif ID_AM==011
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x013f);
#elif ID_AM==100
LCD_WR_REG(0x0020,0x00ef);
LCD_WR_REG(0x0021,0x0000);
#elif ID_AM==101
LCD_WR_REG(0x0020,0x00ef);
LCD_WR_REG(0x0021,0x0000);
#elif ID_AM==110
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x0000);
#elif ID_AM==111
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x0000);
#endif
LCD_WR_REG(0x0030,0x0000);
LCD_WR_REG(0x0031,0x0507);
LCD_WR_REG(0x0032,0x0104);
LCD_WR_REG(0x0035,0x0105);
LCD_WR_REG(0x0036,0x0404);
LCD_WR_REG(0x0037,0x0603);
LCD_WR_REG(0x0038,0x0004);
LCD_WR_REG(0x0039,0x0007);
LCD_WR_REG(0x003c,0x0501);
LCD_WR_REG(0x003d,0x0404);
LCD_WR_REG(0x0050,0x0000);//水平 GRAM起始位置
LCD_WR_REG(0x0051,0x00ef);//水平GRAM終止位置
LCD_WR_REG(0x0052,0x0000);//垂直GRAM起始位置
LCD_WR_REG(0x0053,0x013f);//垂直GRAM終止位置
#ifdef ILI9325
LCD_WR_REG(0x0060,0xa700);//G
#endif
#ifdef ILI9320
LCD_WR_REG(0x0060,0x2700);//G
#endif
LCD_WR_REG(0x0061,0x0001);//Enables the grayscale inversion of the image by setting REV=1.??????????????????????????????
LCD_WR_REG(0x006a,0x0000);//不使用卷曲功能
LCD_WR_REG(0x0080,0x0000);
LCD_WR_REG(0x0081,0x0000);
LCD_WR_REG(0x0082,0x0000);
LCD_WR_REG(0x0083,0x0000);
LCD_WR_REG(0x0084,0x0000);
LCD_WR_REG(0x0085,0x0000);
LCD_WR_REG(0x0090,0x0010);
LCD_WR_REG(0x0092,0x0000);
LCD_WR_REG(0x0093,0x0003);
LCD_WR_REG(0x0095,0x0110);
LCD_WR_REG(0x0097,0x0000);
LCD_WR_REG(0x0098,0x0000);
//顯示畫面寫入 0x0130是不顯示當前畫面
//0x0173是顯示當前畫面
LCD_WR_REG(0x0007,0x0130);
#ifdef Immediately
LCD_WR_REG(0x0007,0x0173);
#endif
//第一個像素的讀取數據是無效值，這里事先讀取一次，舍去無效值
*/
i = CheckController();
if(i==0x9325)
{
LCD_WR_REG(0x00e7,0x0010);
LCD_WR_REG(0x0000,0x0001); //start internal osc
LCD_WR_REG(0x0001,0x0100);
LCD_WR_REG(0x0002,0x0700); //power on sequence
LCD_WR_REG(0x0003,(1<<12)|(1<<5)|(1<<4) ); //65K
LCD_WR_REG(0x0004,0x0000);
LCD_WR_REG(0x0008,0x0207);
LCD_WR_REG(0x0009,0x0000);
LCD_WR_REG(0x000a,0x0000); //display setting
LCD_WR_REG(0x000c,0x0001); //display setting
LCD_WR_REG(0x000d,0x0000); //0f3c
LCD_WR_REG(0x000f,0x0000);
LCD_WR_REG(0x0010,0x0000);
LCD_WR_REG(0x0011,0x0007);
LCD_WR_REG(0x0012,0x0000);
LCD_WR_REG(0x0013,0x0000);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0010,0x1590);
LCD_WR_REG(0x0011,0x0227);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0012,0x009c);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0013,0x1900);
LCD_WR_REG(0x0029,0x0023);
LCD_WR_REG(0x002b,0x000e);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x0000);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0030,0x0007);
LCD_WR_REG(0x0031,0x0707);
LCD_WR_REG(0x0032,0x0006);
LCD_WR_REG(0x0035,0x0704);
LCD_WR_REG(0x0036,0x1f04);
LCD_WR_REG(0x0037,0x0004);
LCD_WR_REG(0x0038,0x0000);
LCD_WR_REG(0x0039,0x0706);
LCD_WR_REG(0x003c,0x0701);
LCD_WR_REG(0x003d,0x000f);
for(i=50000;i>0;i--);
LCD_WR_REG(0x0050,0x0000);
LCD_WR_REG(0x0051,0x00ef);
LCD_WR_REG(0x0052,0x0000);
LCD_WR_REG(0x0053,0x013f);
LCD_WR_REG(0x0060,0xa700);
LCD_WR_REG(0x0061,0x0001);
LCD_WR_REG(0x006a,0x0000);
LCD_WR_REG(0x0080,0x0000);
LCD_WR_REG(0x0081,0x0000);
LCD_WR_REG(0x0082,0x0000);
LCD_WR_REG(0x0083,0x0000);
LCD_WR_REG(0x0084,0x0000);
LCD_WR_REG(0x0085,0x0000);
LCD_WR_REG(0x0090,0x0010);
LCD_WR_REG(0x0092,0x0000);
LCD_WR_REG(0x0093,0x0003);
LCD_WR_REG(0x0095,0x0110);
LCD_WR_REG(0x0097,0x0000);
LCD_WR_REG(0x0098,0x0000);
//display on sequence
LCD_WR_REG(0x0007,0x0133);
LCD_WR_REG(0x0020,0x0000);
LCD_WR_REG(0x0021,0x0000);
}
else if(i==0x9320)
{
LCD_WR_REG(0x00,0x0000);
LCD_WR_REG(0x01,0x0100); //Driver Output Contral.
LCD_WR_REG(0x02,0x0700); //LCD Driver Waveform Contral.
LCD_WR_REG(0x03,0x1030); //Entry Mode Set.
LCD_WR_REG(0x04,0x0000); //Scalling Contral.
LCD_WR_REG(0x08,0x0202); //Display Contral 2.(0x0207)
LCD_WR_REG(0x09,0x0000); //Display Contral 3.(0x0000)
LCD_WR_REG(0x0a,0x0000); //Frame Cycle Contal.(0x0000)
LCD_WR_REG(0x0c,(1<<0)); //Extern Display Interface Contral 1.(0x0000)
LCD_WR_REG(0x0d,0x0000); //Frame Maker Position.
LCD_WR_REG(0x0f,0x0000); //Extern Display Interface Contral 2.
for(i=50000;i>0;i--);
LCD_WR_REG(0x07,0x0101); //Display Contral.
for(i=50000;i>0;i--);
LCD_WR_REG(0x10,(1<<12)|(0<<8)|(1<<7)|(1<<6)|(0<<4)); //Power Control 1.(0x16b0)
LCD_WR_REG(0x11,0x0007); //Power Control 2.(0x0001)
LCD_WR_REG(0x12,(1<<8)|(1<<4)|(0<<0)); //Power Control 3.(0x0138)
LCD_WR_REG(0x13,0x0b00); //Power Control 4.
LCD_WR_REG(0x29,0x0000); //Power Control 7.
LCD_WR_REG(0x2b,(1<<14)|(1<<4));
LCD_WR_REG(0x50,0); //Set X Start.
LCD_WR_REG(0x51,239); //Set X End.
LCD_WR_REG(0x52,0); //Set Y Start.
LCD_WR_REG(0x53,319); //Set Y End.
LCD_WR_REG(0x60,0x2700); //Driver Output Control.
LCD_WR_REG(0x61,0x0001); //Driver Output Control.
LCD_WR_REG(0x6a,0x0000); //Vertical Srcoll Control.
LCD_WR_REG(0x80,0x0000); //Display Position? Partial Display 1.
LCD_WR_REG(0x81,0x0000); //RAM Address Start? Partial Display 1.
LCD_WR_REG(0x82,0x0000); //RAM Address End-Partial Display 1.
LCD_WR_REG(0x83,0x0000); //Displsy Position? Partial Display 2.
LCD_WR_REG(0x84,0x0000); //RAM Address Start? Partial Display 2.
LCD_WR_REG(0x85,0x0000); //RAM Address End? Partial Display 2.
LCD_WR_REG(0x90,(0<<7)|(16<<0)); //Frame Cycle Contral.(0x0013)
LCD_WR_REG(0x92,0x0000); //Panel Interface Contral 2.(0x0000)
LCD_WR_REG(0x93,0x0001); //Panel Interface Contral 3.
LCD_WR_REG(0x95,0x0110); //Frame Cycle Contral.(0x0110)
LCD_WR_REG(0x97,(0<<8)); //
LCD_WR_REG(0x98,0x0000); //Frame Cycle Contral.
LCD_WR_REG(0x07,0x0173); //(0x0173)
}
}
/******************************************
函數名：Lcd寫命令函數
功能：向Lcd指定位置寫入應有命令或數據
入口參數：Index 要尋址的寄存器地址
ConfigTemp 寫入的數據或命令值
返回值：無
******************************************/
void LCD_WR_REG(u16 Index,u16 CongfigTemp)
{
Clr_Cs;
Clr_Rs;
Set_nRd;
DataToWrite(Index);
Clr_nWr;
Set_nWr;
Set_Rs;
DataToWrite(CongfigTemp);
Clr_nWr;
Set_nWr;
Set_Cs;
}
/************************************************
函數名：Lcd寫開始函數
功能：控制Lcd控制引腳 執行寫操作
入口參數：無
返回值：無
************************************************/
void Lcd_WR_Start(void)
{
Clr_Cs;
Clr_Rs;
Set_nRd;
DataToWrite(0x0022);
Clr_nWr;
Set_nWr;
Set_Rs;
}
/*************************************************
函數名：Lcd光標起點定位函數
功能：指定320240液晶上的一點作為寫數據的起始點
入口參數：x 坐標 0~239
y 坐標 0~319
返回值：無
*************************************************/
void Lcd_SetCursor(u8 x,u16 y)
{
LCD_WR_REG(0x20,x);
LCD_WR_REG(0x21,y);
}
/**********************************************
函數名：Lcd全屏擦除函數
功能：將Lcd整屏擦為指定顏色
入口參數：color 指定Lcd全屏顏色 RGB(5-6-5)
返回值：無
***********************************************/
void Lcd_Clear(u16 Color)
{
u32 temp;
Lcd_SetCursor(0x00, 0x0000);
LCD_WR_REG(0x0050,0x00);//水平 GRAM起始位置
LCD_WR_REG(0x0051,239);//水平GRAM終止位置
LCD_WR_REG(0x0052,0x00);//垂直GRAM起始位置
LCD_WR_REG(0x0053,319);//垂直GRAM終止位置
Lcd_WR_Start();
Set_Rs;
for (temp = 0; temp < 76800; temp++)
{
DataToWrite(Color);
Clr_nWr;
Set_nWr;
}
Set_Cs;
}
/**********************************************
函數名：Lcd塊選函數
功能：選定Lcd上指定的矩形區域
注意：xStart和 yStart隨著屏幕的旋轉而改變，位置是矩形框的四個角
入口參數：xStart x方向的起始點
ySrart y方向的終止點
xLong 要選定矩形的x方向長度
yLong 要選定矩形的y方向長度
返回值：無
***********************************************/
void Lcd_SetBox(u8 xStart,u16 yStart,u8 xLong,u16 yLong,u16 x_offset,u16 y_offset)
{
#if ID_AM==000
Lcd_SetCursor(xStart+xLong-1+x_offset,yStart+yLong-1+y_offset);
#elif ID_AM==001
Lcd_SetCursor(xStart+xLong-1+x_offset,yStart+yLong-1+y_offset);
#elif ID_AM==010
Lcd_SetCursor(xStart+x_offset,yStart+yLong-1+y_offset);
#elif ID_AM==011
Lcd_SetCursor(xStart+x_offset,yStart+yLong-1+y_offset);
#elif ID_AM==100
Lcd_SetCursor(xStart+xLong-1+x_offset,yStart+y_offset);
#elif ID_AM==101
Lcd_SetCursor(xStart+xLong-1+x_offset,yStart+y_offset);
#elif ID_AM==110
Lcd_SetCursor(xStart+x_offset,yStart+y_offset);
#elif ID_AM==111
Lcd_SetCursor(xStart+x_offset,yStart+y_offset);
#endif
LCD_WR_REG(0x0050,xStart+x_offset);//水平 GRAM起始位置
LCD_WR_REG(0x0051,xStart+xLong-1+x_offset);//水平GRAM終止位置
LCD_WR_REG(0x0052,yStart+y_offset);//垂直GRAM起始位置
LCD_WR_REG(0x0053,yStart+yLong-1+y_offset);//垂直GRAM終止位置
}
void Lcd_ColorBox(u8 xStart,u16 yStart,u8 xLong,u16 yLong,u16 Color)
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -