/************************************************************************
* WWW.3721IT.COM為你提供服務,請保留表頭謝謝,硬件工程師之家		*
*									*				
*************************************************************************/

/******************************************************************************************************
** Descriptions:		sd 卡驅動軟件包: SD卡物理層 ---- SD卡SPI模式支持的命令(頭文件) 
********************************************************************************************************/
#ifndef 	__sdcmd_h
#define 	__sdcmd_h
/*
 *******************************************************
	
		SD 卡的相關命令與響應宏定義
	
 *******************************************************
*/

/* 命令響應定義 define command's response */
#define R1 		1
#define R1B 	2
#define R2 		3
#define R3 		4

/* R1和R2高字節錯誤碼 R1 and upper byte of R2 error code */
#define MSK_IDLE          		  0x01
#define MSK_ERASE_RST     		  0x02
#define MSK_ILL_CMD       		  0x04
#define MSK_CRC_ERR       		  0x08
#define MSK_ERASE_SEQ_ERR 		  0x10
#define MSK_ADDR_ERR      		  0x20
#define MSK_PARAM_ERR     		  0x40

/* R2低字節錯誤碼 lower byte of R2 error code */
#define MSK_TOK_ERROR             0x01
#define MSK_TOK_CC_ERROR          0x02
#define MSK_TOK_ECC_FAILED        0x04
#define MSK_TOK_CC_OUTOFRANGE     0x08
#define MSK_TOK_CC_LOCKED         0x10



/* 數據令牌 Data Tokens */
#define SD_TOK_READ_STARTBLOCK    0xFE
#define SD_TOK_WRITE_STARTBLOCK   0xFE
#define SD_TOK_READ_STARTBLOCK_M  0xFE
#define SD_TOK_WRITE_STARTBLOCK_M 0xFC
#define SD_TOK_STOP_MULTI         0xFD

/* 數據響應令牌 Data Response Tokens */
#define SD_RESP_DATA_MSK		  0x0F		//數據響應掩碼
#define SD_RESP_DATA_ACCETPTED	  0x05		//數據被接受
#define SD_RESP_DATA_REJECT_CRC	  0x0B      //由于CRC錯誤而被拒絕
#define SD_RESP_DATA_REJECT_WRITE 0x0D		//由于寫錯誤而被拒絕

/* 等待類型 Wait Type */
#define SD_WAIT_READ			  0x00		//讀等待
#define SD_WAIT_WRITE			  0x01		//寫等待
#define SD_WAIT_ERASE		 	  0x02		//擦除等待


#define SD_READREG_TIMEOUT		  8


/*
*********************************************

     SD卡SPI模式下命令集

*********************************************
*/

/******************************** 基本命令集 Basic command set **************************/
/* 復位SD 卡 Reset cards to idle state */
#define CMD0 0
#define CMD0_R R1

/* 讀OCR寄存器 Read the OCR (MMC mode, do not use for SD cards) */
#define CMD1 1
#define CMD1_R R1

/* 讀CSD寄存器 Card sends the CSD */
#define CMD9 9
#define CMD9_R R1

/* 讀CID寄存器 Card sends CID */
#define CMD10 10
#define CMD10_R R1

/* 停止讀多塊時的數據傳輸 Stop a multiple block (stream) read/write operation */
#define CMD12 12
#define CMD12_R R1B

/* 讀 Card_Status 寄存器 Get the addressed card's status register */
#define CMD13 13
#define CMD13_R R2

/***************************** 塊讀命令集 Block read commands **************************/

/* 設置塊的長度 Set the block length */
#define CMD16 16
#define CMD16_R R1

/* 讀單塊 Read a single block */
#define CMD17 17
#define CMD17_R R1

/* 讀多塊,直至主機發送CMD12為止 Read multiple blocks until a CMD12 */
#define CMD18 18
#define CMD18_R R1

/***************************** 塊寫命令集 Block write commands *************************/
/* 寫單塊 Write a block of the size selected with CMD16 */
#define CMD24 24
#define CMD24_R R1

/* 寫多塊 Multiple block write until a CMD12 */
#define CMD25 25
#define CMD25_R R1

/* 寫CSD寄存器 Program the programmable bits of the CSD */
#define CMD27 27
#define CMD27_R R1

/***************************** 寫保護 Write protection *****************************/
/* Set the write protection bit of the addressed group */
#define CMD28 28
#define CMD28_R R1B

/* Clear the write protection bit of the addressed group */
#define CMD29 29
#define CMD29_R R1B

/* Ask the card for the status of the write protection bits */
#define CMD30 30
#define CMD30_R R1

/***************************** 擦除命令 Erase commands *******************************/
/* 設置擦除塊的起始地址 Set the address of the first write block to be erased */
#define CMD32 32
#define CMD32_R R1

/* 設置擦除塊的終止地址 Set the address of the last write block to be erased */
#define CMD33 33
#define CMD33_R R1

/* 擦除所選擇的塊 Erase the selected write blocks */
#define CMD38 38
#define CMD38_R R1B

/***************************** 鎖卡命令 Lock Card commands ***************************/
/* 設置/復位密碼或上鎖/解鎖卡 Set/reset the password or lock/unlock the card */
#define CMD42 42
#define CMD42_R	R1B
/* Commands from 42 to 54, not defined here */

/***************************** 應用命令 Application-specific commands ****************/
/* 禁止下一個命令為應用命令  Flag that the next command is application-specific */
#define CMD55 55
#define CMD55_R R1

/* 應用命令的通用I/O  General purpose I/O for application-specific commands */
#define CMD56 56
#define CMD56_R R1

/* 讀OCR寄存器  Read the OCR (SPI mode only) */
#define CMD58 58
#define CMD58_R R3

/* 使能或禁止 CRC Turn CRC on or off */
#define CMD59 59
#define CMD59_R R1

/***************************** 應用命令 Application-specific commands ***************/
/* 獲取 SD Status寄存器 Get the SD card's status */
#define ACMD13 13
#define ACMD13_R R2

/* 得到已寫入卡中的塊的個數 Get the number of written write blocks (Minus errors ) */
#define ACMD22 22
#define ACMD22_R R1

/* 在寫之前,設置預先擦除的塊的個數 Set the number of write blocks to be pre-erased before writing */
#define ACMD23 23
#define ACMD23_R R1

/* 讀取OCR寄存器 Get the card's OCR (SD mode) */
#define ACMD41 41
#define ACMD41_R R1

/* 連接/斷開CD/DATA[3]引腳上的上拉電阻 Connect or disconnect the 50kOhm internal pull-up on CD/DAT[3] */
#define ACMD42 42
#define ACMD42_R R1

/* 讀取SCR寄存器 Get the SD configuration register */
#define ACMD51 51
#define ACMD51_R R1



uint8 SD_SendCmd(uint8 cmd, uint8 *param, uint8 resptype, uint8 *resp);  // 一個SPI命令 
void SD_PackParam(uint8 *parameter, uint32 value);						 // 封裝參數
uint8 SD_BlockCommand(uint8 cmd, uint8 resptype, uint32 parameter);		 // 塊命令 

	
uint8 SD_ResetSD(void);											// 復位SD卡

uint8 SD_ReadCSD(uint8 csdlen, uint8 *recbuf);					// 讀CSD 			read CSD register
uint8 SD_ReadCID(uint8 cidlen, uint8 *recbuf);					// 讀CID			read CID register
uint8 SD_StopTransmission(void);								// 停止傳輸			

uint8 SD_ReadCard_Status(uint8 len, uint8 *buffer);				// 讀Card Status	read Card Status register
uint8 SD_SetBlockLen(uint32 length);							// 設置塊長度

uint8 SD_ReadSingleBlock(uint32 blockaddr);						// 讀單塊
uint8 SD_ReadMultipleBlock(uint32 blockaddr);					// 讀多塊

uint8 SD_WriteSingleBlock(uint32 blockaddr);					// 寫單塊
uint8 SD_WriteMultipleBlock(uint32 blockaddr);					// 寫多塊 


uint8 SD_ProgramCSD(uint8 len, uint8 *buff);					// 寫CSD寄存器  	write CSD register 

uint8 SD_EraseStartBlock(uint32 startblock);					// 擦塊起始地址
uint8 SD_EraseEndBlock(uint32 endblock);						// 擦塊終止地址
uint8 SD_EraseSelectedBlock(void);								// 擦除所選的塊


uint8 SD_ReadOCR(uint8 ocrlen,uint8 *recbuf);					// 讀OCR			read OCR register
uint8 SD_EnableCRC(uint8 bEnable);								// 使能CRC校驗		enable CRC


// 特殊應用命令
uint8 SD_ReadSD_Status(uint8 sdslen, uint8 *recbuf);			// 讀SD_Status  read SD_Status 
uint8 SD_GetNumWRBlcoks(uint32 *blocknum);						// 得到正確寫入塊數
uint8 SD_ReadSCR(uint8 scrlen, uint8 *recbuf);					// 讀SCR 		read SCR register


// 數據流函數
uint8 SD_ReadRegister(uint32 len, uint8 *recbuf);						// 讀數據
uint8 SD_ReadBlockData(uint32 len, uint8 *recbuf);						// 讀塊數據
uint8 SD_WriteBlockData(uint8 bmulti, uint32 len, uint8 *sendbuf);		// 寫塊數據

// 其它函數
void SD_StopMultiToken(void);									// 停止多塊寫令牌
uint8 SD_WaitBusy(uint8 waittype);								// 忙
void SD_SPIDelay(uint8 value);									// 發生SPI時鐘


#endif