/*
 *
 *
 *                     Win32 include file
 *          for accessing the 32-bit GPIB DLL (gpib-32.dll)
 *
 *
 *         Contains user variables (ibsta, iberr, ibcnt, ibcntl),
 *         function prototypes and useful defined constants for
 *         calling NI-488 and NI-488.2 routines from a Microsoft
 *         C/C++ Win32 application.
 *
 *
 *            Copyright 1995 National Instruments Corporation
 *
 */

#ifndef DECL_32_H       // ensure we are only included once
#define DECL_32_H

#ifdef __cplusplus
extern "C" {
#endif


/***************************************************************************/
/*    HANDY CONSTANTS FOR USE BY APPLICATION PROGRAMS ...                  */
/***************************************************************************/
#define UNL  0x3f  /* GPIB unlisten command                */
#define UNT  0x5f  /* GPIB untalk command                  */
#define GTL  0x01  /* GPIB go to local                     */
#define SDC  0x04  /* GPIB selected device clear           */
#define PPC  0x05  /* GPIB parallel poll configure         */
#define GET  0x08  /* GPIB group execute trigger           */
#define TCT  0x09  /* GPIB take control                    */
#define LLO  0x11  /* GPIB local lock out                  */
#define DCL  0x14  /* GPIB device clear                    */
#define PPU  0x15  /* GPIB parallel poll unconfigure       */
#define SPE  0x18  /* GPIB serial poll enable              */
#define SPD  0x19  /* GPIB serial poll disable             */
#define PPE  0x60  /* GPIB parallel poll enable            */
#define PPD  0x70  /* GPIB parallel poll disable           */

/* GPIB status bit vector :                                */
/*       global variable ibsta and wait mask               */

#define ERR     (1<<15) /* Error detected                  */
#define TIMO    (1<<14) /* Timeout                         */
#define END     (1<<13) /* EOI or EOS detected             */
#define SRQI    (1<<12) /* SRQ detected by CIC             */
#define RQS     (1<<11) /* Device needs service            */
#define CMPL    (1<<8)  /* I/O completed                   */
#define LOK     (1<<7)  /* Local lockout state             */
#define REM     (1<<6)  /* Remote state                    */
#define CIC     (1<<5)  /* Controller-in-Charge            */
#define ATN     (1<<4)  /* Attention asserted              */
#define TACS    (1<<3)  /* Talker active                   */
#define LACS    (1<<2)  /* Listener active                 */
#define DTAS    (1<<1)  /* Device trigger state            */
#define DCAS    (1<<0)  /* Device clear state              */

/* Error messages returned in global variable iberr        */

#define EDVR  0  /* System error                           */
#define ECIC  1  /* Function requires GPIB board to be CIC */
#define ENOL  2  /* Write function detected no Listeners   */
#define EADR  3  /* Interface board not addressed correctly*/
#define EARG  4  /* Invalid argument to function call      */
#define ESAC  5  /* Function requires GPIB board to be SAC */
#define EABO  6  /* I/O operation aborted                  */
#define ENEB  7  /* Non-existent interface board           */
#define EDMA  8  /* Error performing DMA                   */
#define EOIP 10  /* I/O operation started before previous  */
                 /* operation completed                    */
#define ECAP 11  /* No capability for intended operation   */
#define EFSO 12  /* File system operation error            */
#define EBUS 14  /* Command error during device call       */
#define ESTB 15  /* Serial poll status byte lost           */
#define ESRQ 16  /* SRQ remains asserted                   */
#define ETAB 20  /* The return buffer is full.             */
#define ELCK 21  /* Address or board is locked.            */

/* EOS mode bits                                           */

#define BIN  (1<<12) /* Eight bit compare                  */
#define XEOS (1<<11) /* Send END with EOS byte             */
#define REOS (1<<10) /* Terminate read on EOS              */

/* Timeout values and meanings                             */

#define TNONE    0   /* Infinite timeout (disabled)        */
#define T10us    1   /* Timeout of 10 us (ideal)           */
#define T30us    2   /* Timeout of 30 us (ideal)           */
#define T100us   3   /* Timeout of 100 us (ideal)          */
#define T300us   4   /* Timeout of 300 us (ideal)          */
#define T1ms     5   /* Timeout of 1 ms (ideal)            */
#define T3ms     6   /* Timeout of 3 ms (ideal)            */
#define T10ms    7   /* Timeout of 10 ms (ideal)           */
#define T30ms    8   /* Timeout of 30 ms (ideal)           */
#define T100ms   9   /* Timeout of 100 ms (ideal)          */
#define T300ms  10   /* Timeout of 300 ms (ideal)          */
#define T1s     11   /* Timeout of 1 s (ideal)             */
#define T3s     12   /* Timeout of 3 s (ideal)             */
#define T10s    13   /* Timeout of 10 s (ideal)            */
#define T30s    14   /* Timeout of 30 s (ideal)            */
#define T100s   15   /* Timeout of 100 s (ideal)           */
#define T300s   16   /* Timeout of 300 s (ideal)           */
#define T1000s  17   /* Timeout of 1000 s (ideal)          */


/*  IBLN Constants                                         */
#define NO_SAD   0
#define ALL_SAD -1


/*  The following constants are used for the second parameter of the
 *  ibconfig function.  They are the "option" selection codes.
 */
#define  IbcPAD        0x0001      /* Primary Address                      */
#define  IbcSAD        0x0002      /* Secondary Address                    */
#define  IbcTMO        0x0003      /* Timeout Value                        */
#define  IbcEOT        0x0004      /* Send EOI with last data byte?        */
#define  IbcPPC        0x0005      /* Parallel Poll Configure              */
#define  IbcREADDR     0x0006      /* Repeat Addressing                    */
#define  IbcAUTOPOLL   0x0007      /* Disable Auto Serial Polling          */
#define  IbcCICPROT    0x0008      /* Use the CIC Protocol?                */
#define  IbcIRQ        0x0009      /* Use PIO for I/O                      */
#define  IbcSC         0x000A      /* Board is System Controller?          */
#define  IbcSRE        0x000B      /* Assert SRE on device calls?          */
#define  IbcEOSrd      0x000C      /* Terminate reads on EOS               */
#define  IbcEOSwrt     0x000D      /* Send EOI with EOS character          */
#define  IbcEOScmp     0x000E      /* Use 7 or 8-bit EOS compare           */
#define  IbcEOSchar    0x000F      /* The EOS character.                   */
#define  IbcPP2        0x0010      /* Use Parallel Poll Mode 2.            */
#define  IbcTIMING     0x0011      /* NORMAL, HIGH, or VERY_HIGH timing.   */
#define  IbcDMA        0x0012      /* Use DMA for I/O                      */
#define  IbcReadAdjust 0x0013      /* Swap bytes during an ibrd.           */
#define  IbcWriteAdjust 0x014      /* Swap bytes during an ibwrt.          */
#define  IbcSendLLO    0x0017      /* Enable/disable the sending of LLO.      */
#define  IbcSPollTime  0x0018      /* Set the timeout value for serial polls. */
#define  IbcPPollTime  0x0019      /* Set the parallel poll length period.    */
#define  IbcEndBitIsNormal 0x001A  /* Remove EOS from END bit of IBSTA.       */
#define  IbcUnAddr         0x001B  /* Enable/disable device unaddressing.     */
#define  IbcSignalNumber   0x001C  /* Set UNIX signal number - unsupported */
#define  IbcBlockIfLocked  0x001D   /* Enable/disable blocking for locked boards/devices         */
#define  IbcHSCableLength  0x001F  /* Length of cable specified for high speed timing.*/
#define  IbcIst        0x0020      /* Set the IST bit.                     */
#define  IbcRsv        0x0021      /* Set the RSV byte.                    */

/*
 *    Constants that can be used (in addition to the ibconfig constants)
 *    when calling the ibask() function.
 */

#define  IbaPAD            IbcPAD
#define  IbaSAD            IbcSAD
#define  IbaTMO            IbcTMO
#define  IbaEOT            IbcEOT
#define  IbaPPC            IbcPPC
#define  IbaREADDR         IbcREADDR
#define  IbaAUTOPOLL       IbcAUTOPOLL
#define  IbaCICPROT        IbcCICPROT
#define  IbaIRQ            IbcIRQ
#define  IbaSC             IbcSC
#define  IbaSRE            IbcSRE
#define  IbaEOSrd          IbcEOSrd
#define  IbaEOSwrt         IbcEOSwrt
#define  IbaEOScmp         IbcEOScmp
#define  IbaEOSchar        IbcEOSchar
#define  IbaPP2            IbcPP2
#define  IbaTIMING         IbcTIMING
#define  IbaDMA            IbcDMA
#define  IbaReadAdjust     IbcReadAdjust
#define  IbaWriteAdjust    IbcWriteAdjust
#define  IbaSendLLO        IbcSendLLO
#define  IbaSPollTime      IbcSPollTime
#define  IbaPPollTime      IbcPPollTime
#define  IbaEndBitIsNormal IbcEndBitIsNormal
#define  IbaUnAddr         IbcUnAddr
#define  IbaSignalNumber   IbcSignalNumber
#define  IbaBlockIfLocked  IbcBlockIfLocked
#define  IbaHSCableLength  IbcHSCableLength
#define  IbaIst            IbcIst
#define  IbaRsv            IbcRsv

#define  IbaBNA            0x0200   /* A device's access board.                  */


/* Values used by the Send 488.2 command. */
#define  NULLend 0x00  /* Do nothing at the end of a transfer.*/
#define  NLend   0x01  /* Send NL with EOI after a transfer.  */
#define  DABend  0x02  /* Send EOI with the last DAB.         */

/* Value used by the 488.2 Receive command.
 */
#define  STOPend     0x0100


/* Address type (for 488.2 calls) */

typedef short Addr4882_t;       /* System dependent: must be 16 bits */

/*
 *  This macro can be used to easily create an entry in address list
 *  that is required by many of the 488.2 functions. The primary address goes in the
 *  lower 8-bits and the secondary address goes in the upper 8-bits.