#define CarrierSenseErrors		EMAC_TXC_CRSERR	/* Carrier Sense Deasserted During TX Frame Count */#define UnicastFramesXmittedOK		EMAC_TXC_UNICST	/* Unicast TX Frame Count */#define MulticastFramesXmittedOK	EMAC_TXC_MULTI	/* Multicast TX Frame Count */#define BroadcastFramesXmittedOK	EMAC_TXC_BROAD	/* Broadcast TX Frame Count */#define FramesWithExcessiveDeferral	EMAC_TXC_XS_DFR	/* TX Frames With Excessive Deferral Count */#define MACControlFramesTransmitted	EMAC_TXC_MACCTL	/* MAC Control TX Frame Count */#define FramesTransmittedAll		EMAC_TXC_ALLFRM	/* Overall TX Frame Count */#define OctetsTransmittedAll		EMAC_TXC_ALLOCT	/* Overall TX Octet Count */#define FramesLenEq64Transmitted	EMAC_TXC_EQ64	/* Good TX Frame Count - Byte Count x = 64 */#define FramesLen65_127Transmitted	EMAC_TXC_LT128	/* Good TX Frame Count - Byte Count  64 <= x < 128 */#define FramesLen128_255Transmitted	EMAC_TXC_LT256	/* Good TX Frame Count - Byte Count 128 <= x < 256 */#define FramesLen256_511Transmitted	EMAC_TXC_LT512	/* Good TX Frame Count - Byte Count 256 <= x < 512 */#define FramesLen512_1023Transmitted	EMAC_TXC_LT1024	/* Good TX Frame Count - Byte Count 512 <= x < 1024 */#define FramesLen1024_MaxTransmitted	EMAC_TXC_GE1024	/* Good TX Frame Count - Byte Count x >= 1024 */#define TxAbortedFrames			EMAC_TXC_ABORT	/* Total TX Frames Aborted Count *//* * System MMR Register Bits And Macros * * Disclaimer:	All macros are intended to make C and Assembly code more readable. *		Use these macros carefully, as any that do left shifts for field *		depositing will result in the lower order bits being destroyed.  Any *		macro that shifts left to properly position the bit-field should be *		used as part of an OR to initialize a register and NOT as a dynamic *		modifier UNLESS the lower order bits are saved and ORed back in when *		the macro is used. *//* * ETHERNET 10/100 CONTROLLER MASKS *//* EMAC_OPMODE Masks */#define	RE		0x00000001	/* Receiver Enable */#define	ASTP		0x00000002	/* Enable Automatic Pad Stripping On RX Frames */#define	HU		0x00000010	/* Hash Filter Unicast Address */#define	HM		0x00000020	/* Hash Filter Multicast Address */#define	PAM		0x00000040	/* Pass-All-Multicast Mode Enable */#define	PR		0x00000080	/* Promiscuous Mode Enable */#define	IFE		0x00000100	/* Inverse Filtering Enable */#define	DBF		0x00000200	/* Disable Broadcast Frame Reception */#define	PBF		0x00000400	/* Pass Bad Frames Enable */#define	PSF		0x00000800	/* Pass Short Frames Enable */#define	RAF		0x00001000	/* Receive-All Mode */#define	TE		0x00010000	/* Transmitter Enable */#define	DTXPAD		0x00020000	/* Disable Automatic TX Padding */#define	DTXCRC		0x00040000	/* Disable Automatic TX CRC Generation */#define	DC		0x00080000	/* Deferral Check */#define	BOLMT		0x00300000	/* Back-Off Limit */#define	BOLMT_10	0x00000000	/* 10-bit range */#define	BOLMT_8		0x00100000	/* 8-bit range */#define	BOLMT_4		0x00200000	/* 4-bit range */#define	BOLMT_1		0x00300000	/* 1-bit range */#define	DRTY		0x00400000	/* Disable TX Retry On Collision */#define	LCTRE		0x00800000	/* Enable TX Retry On Late Collision */#define	RMII		0x01000000	/* RMII/MII* Mode */#define	RMII_10		0x02000000	/* Speed Select for RMII Port (10MBit/100MBit*) */#define	FDMODE		0x04000000	/* Duplex Mode Enable (Full/Half*) */#define	LB		0x08000000	/* Internal Loopback Enable */#define	DRO		0x10000000	/* Disable Receive Own Frames (Half-Duplex Mode) *//* EMAC_STAADD Masks */#define	STABUSY		0x00000001	/* Initiate Station Mgt Reg Access / STA Busy Stat */#define	STAOP		0x00000002	/* Station Management Operation Code (Write/Read*) */#define	STADISPRE	0x00000004	/* Disable Preamble Generation */#define	STAIE		0x00000008	/* Station Mgt. Transfer Done Interrupt Enable */#define	REGAD		0x000007C0	/* STA Register Address */#define	PHYAD		0x0000F800	/* PHY Device Address */#define	SET_REGAD(x)	(((x)&0x1F)<<  6 )	/* Set STA Register Address */#define	SET_PHYAD(x)	(((x)&0x1F)<< 11 )	/* Set PHY Device Address *//* EMAC_STADAT Mask */#define	STADATA		0x0000FFFF	/* Station Management Data *//* EMAC_FLC Masks */#define	FLCBUSY		0x00000001	/* Send Flow Ctrl Frame / Flow Ctrl Busy Status */#define	FLCE		0x00000002	/* Flow Control Enable */#define	PCF		0x00000004	/* Pass Control Frames */#define	BKPRSEN		0x00000008	/* Enable Backpressure */#define	FLCPAUSE	0xFFFF0000	/* Pause Time */#define	SET_FLCPAUSE(x)	(((x)&0xFFFF)<< 16)	/* Set Pause Time *//* EMAC_WKUP_CTL Masks */#define	CAPWKFRM	0x00000001	/* Capture Wake-Up Frames */#define	MPKE		0x00000002	/* Magic Packet Enable */#define	RWKE		0x00000004	/* Remote Wake-Up Frame Enable */#define	GUWKE		0x00000008	/* Global Unicast Wake Enable */#define	MPKS		0x00000020	/* Magic Packet Received Status */#define	RWKS		0x00000F00	/* Wake-Up Frame Received Status, Filters 3:0 *//* EMAC_WKUP_FFCMD Masks */#define	WF0_E		0x00000001	/* Enable Wake-Up Filter 0 */#define	WF0_T		0x00000008	/* Wake-Up Filter 0 Addr Type (Multicast/Unicast*) */#define	WF1_E		0x00000100	/* Enable Wake-Up Filter 1 */#define	WF1_T		0x00000800	/* Wake-Up Filter 1 Addr Type (Multicast/Unicast*) */#define	WF2_E		0x00010000	/* Enable Wake-Up Filter 2 */#define	WF2_T		0x00080000	/* Wake-Up Filter 2 Addr Type (Multicast/Unicast*) */#define	WF3_E		0x01000000	/* Enable Wake-Up Filter 3 */#define	WF3_T		0x08000000	/* Wake-Up Filter 3 Addr Type (Multicast/Unicast*) *//* EMAC_WKUP_FFOFF Masks */#define	WF0_OFF		0x000000FF	/* Wake-Up Filter 0 Pattern Offset */#define	WF1_OFF		0x0000FF00	/* Wake-Up Filter 1 Pattern Offset */#define	WF2_OFF		0x00FF0000	/* Wake-Up Filter 2 Pattern Offset */#define	WF3_OFF		0xFF000000	/* Wake-Up Filter 3 Pattern Offset */#define	SET_WF0_OFF(x)	(((x)&0xFF)<<  0 )	/* Set Wake-Up Filter 0 Byte Offset */#define	SET_WF1_OFF(x)	(((x)&0xFF)<<  8 )	/* Set Wake-Up Filter 1 Byte Offset */#define	SET_WF2_OFF(x)	(((x)&0xFF)<< 16 )	/* Set Wake-Up Filter 2 Byte Offset */#define	SET_WF3_OFF(x)	(((x)&0xFF)<< 24 )	/* Set Wake-Up Filter 3 Byte Offset *//* Set ALL Offsets */#define	SET_WF_OFFS(x0,x1,x2,x3)	(SET_WF0_OFF((x0))|SET_WF1_OFF((x1))|SET_WF2_OFF((x2))|SET_WF3_OFF((x3)))/* EMAC_WKUP_FFCRC0 Masks */#define	WF0_CRC		0x0000FFFF	/* Wake-Up Filter 0 Pattern CRC */#define	WF1_CRC		0xFFFF0000	/* Wake-Up Filter 1 Pattern CRC */#define	SET_WF0_CRC(x)	(((x)&0xFFFF)<< 0)	/* Set Wake-Up Filter 0 Target CRC */#define	SET_WF1_CRC(x)	(((x)&0xFFFF)<< 16)	/* Set Wake-Up Filter 1 Target CRC *//* EMAC_WKUP_FFCRC1 Masks */#define	WF2_CRC		0x0000FFFF	/* Wake-Up Filter 2 Pattern CRC */#define	WF3_CRC		0xFFFF0000	/* Wake-Up Filter 3 Pattern CRC */#define	SET_WF2_CRC(x)	(((x)&0xFFFF)<< 0)	/* Set Wake-Up Filter 2 Target CRC */#define	SET_WF3_CRC(x)	(((x)&0xFFFF)<< 16)	/* Set Wake-Up Filter 3 Target CRC *//* EMAC_SYSCTL Masks */#define	PHYIE		0x00000001	/* PHY_INT Interrupt Enable */#define	RXDWA		0x00000002	/* Receive Frame DMA Word Alignment (Odd/Even*) */#define	RXCKS		0x00000004	/* Enable RX Frame TCP/UDP Checksum Computation */#define	MDCDIV		0x00003F00	/* SCLK:MDC Clock Divisor [MDC=SCLK/(2*(N+1))] */#define	SET_MDCDIV(x)	(((x)&0x3F)<< 8)	/* Set MDC Clock Divisor *//* EMAC_SYSTAT Masks */#define	PHYINT		0x00000001	/* PHY_INT Interrupt Status */#define	MMCINT		0x00000002	/* MMC Counter Interrupt Status */#define	RXFSINT		0x00000004	/* RX Frame-Status Interrupt Status */#define	TXFSINT		0x00000008	/* TX Frame-Status Interrupt Status */#define	WAKEDET		0x00000010	/* Wake-Up Detected Status */#define	RXDMAERR	0x00000020	/* RX DMA Direction Error Status */#define	TXDMAERR	0x00000040	/* TX DMA Direction Error Status */#define	STMDONE		0x00000080	/* Station Mgt. Transfer Done Interrupt Status *//* EMAC_RX_STAT, EMAC_RX_STKY, and EMAC_RX_IRQE Masks */#define	RX_FRLEN	0x000007FF	/* Frame Length In Bytes */#define	RX_COMP		0x00001000	/* RX Frame Complete */#define	RX_OK		0x00002000	/* RX Frame Received With No Errors */#define	RX_LONG		0x00004000	/* RX Frame Too Long Error */#define	RX_ALIGN	0x00008000	/* RX Frame Alignment Error */#define	RX_CRC		0x00010000	/* RX Frame CRC Error */#define	RX_LEN		0x00020000	/* RX Frame Length Error */#define	RX_FRAG		0x00040000	/* RX Frame Fragment Error */#define	RX_ADDR		0x00080000	/* RX Frame Address Filter Failed Error */#define	RX_DMAO		0x00100000	/* RX Frame DMA Overrun Error */#define	RX_PHY		0x00200000	/* RX Frame PHY Error */#define	RX_LATE		0x00400000	/* RX Frame Late Collision Error */#define	RX_RANGE	0x00800000	/* RX Frame Length Field Out of Range Error */#define	RX_MULTI	0x01000000	/* RX Multicast Frame Indicator */#define	RX_BROAD	0x02000000	/* RX Broadcast Frame Indicator */#define	RX_CTL		0x04000000	/* RX Control Frame Indicator */#define	RX_UCTL		0x08000000	/* Unsupported RX Control Frame Indicator */#define	RX_TYPE		0x10000000	/* RX Typed Frame Indicator */#define	RX_VLAN1	0x20000000	/* RX VLAN1 Frame Indicator */#define	RX_VLAN2	0x40000000	/* RX VLAN2 Frame Indicator */#define	RX_ACCEPT	0x80000000	/* RX Frame Accepted Indicator *//*  EMAC_TX_STAT, EMAC_TX_STKY, and EMAC_TX_IRQE Masks */#define	TX_COMP		0x00000001	/* TX Frame Complete */#define	TX_OK		0x00000002	/* TX Frame Sent With No Errors */#define	TX_ECOLL	0x00000004	/* TX Frame Excessive Collision Error */#define	TX_LATE		0x00000008	/* TX Frame Late Collision Error */#define	TX_DMAU		0x00000010	/* TX Frame DMA Underrun Error (STAT) */#define	TX_MACE		0x00000010	/* Internal MAC Error Detected (STKY and IRQE) */#define	TX_EDEFER	0x00000020	/* TX Frame Excessive Deferral Error */#define	TX_BROAD	0x00000040	/* TX Broadcast Frame Indicator */#define	TX_MULTI	0x00000080	/* TX Multicast Frame Indicator */#define	TX_CCNT		0x00000F00	/* TX Frame Collision Count */#define	TX_DEFER	0x00001000	/* TX Frame Deferred Indicator */#define	TX_CRS		0x00002000	/* TX Frame Carrier Sense Not Asserted Error */#define	TX_LOSS		0x00004000	/* TX Frame Carrier Lost During TX Error */#define	TX_RETRY	0x00008000	/* TX Frame Successful After Retry */#define	TX_FRLEN	0x07FF0000	/* TX Frame Length (Bytes) *//* EMAC_MMC_CTL Masks */#define	RSTC		0x00000001	/* Reset All Counters */#define	CROLL		0x00000002	/* Counter Roll-Over Enable */#define	CCOR		0x00000004	/* Counter Clear-On-Read Mode Enable */#define	MMCE		0x00000008	/* Enable MMC Counter Operation *//* EMAC_MMC_RIRQS and EMAC_MMC_RIRQE Masks */#define	RX_OK_CNT	0x00000001	/* RX Frames Received With No Errors */#define	RX_FCS_CNT	0x00000002	/* RX Frames W/Frame Check Sequence Errors */#define	RX_ALIGN_CNT	0x00000004	/* RX Frames With Alignment Errors */#define	RX_OCTET_CNT	0x00000008	/* RX Octets Received OK */#define	RX_LOST_CNT	0x00000010	/* RX Frames Lost Due To Internal MAC RX Error */#define	RX_UNI_CNT	0x00000020	/* Unicast RX Frames Received OK */#define	RX_MULTI_CNT	0x00000040	/* Multicast RX Frames Received OK */#define	RX_BROAD_CNT	0x00000080	/* Broadcast RX Frames Received OK */#define	RX_IRL_CNT	0x00000100	/* RX Frames With In-Range Length Errors */#define	RX_ORL_CNT	0x00000200	/* RX Frames With Out-Of-Range Length Errors */#define	RX_LONG_CNT	0x00000400	/* RX Frames With Frame Too Long Errors */#define	RX_MACCTL_CNT	0x00000800	/* MAC Control RX Frames Received */#define	RX_OPCODE_CTL	0x00001000	/* Unsupported Op-Code RX Frames Received */#define	RX_PAUSE_CNT	0x00002000	/* PAUSEMAC Control RX Frames Received */#define	RX_ALLF_CNT	0x00004000	/* All RX Frames Received */#define	RX_ALLO_CNT	0x00008000	/* All RX Octets Received */#define	RX_TYPED_CNT	0x00010000	/* Typed RX Frames Received */#define	RX_SHORT_CNT	0x00020000	/* RX Frame Fragments (< 64 Bytes) Received */#define	RX_EQ64_CNT	0x00040000	/* 64-Byte RX Frames Received */#define	RX_LT128_CNT	0x00080000	/* 65-127-Byte RX Frames Received */#define	RX_LT256_CNT	0x00100000	/* 128-255-Byte RX Frames Received */#define	RX_LT512_CNT	0x00200000	/* 256-511-Byte RX Frames Received */#define	RX_LT1024_CNT	0x00400000	/* 512-1023-Byte RX Frames Received */#define	RX_GE1024_CNT	0x00800000	/* 1024-Max-Byte RX Frames Received *//* EMAC_MMC_TIRQS and EMAC_MMC_TIRQE Masks */#define	TX_OK_CNT	0x00000001	/* TX Frames Sent OK */#define	TX_SCOLL_CNT	0x00000002	/* TX Frames With Single Collisions */#define	TX_MCOLL_CNT	0x00000004	/* TX Frames With Multiple Collisions */#define	TX_OCTET_CNT	0x00000008	/* TX Octets Sent OK */#define	TX_DEFER_CNT	0x00000010	/* TX Frames With Deferred Transmission */#define	TX_LATE_CNT	0x00000020	/* TX Frames With Late Collisions */#define	TX_ABORTC_CNT	0x00000040	/* TX Frames Aborted Due To Excess Collisions */#define	TX_LOST_CNT	0x00000080	/* TX Frames Lost Due To Internal MAC TX Error */#define	TX_CRS_CNT	0x00000100	/* TX Frames With Carrier Sense Errors */#define	TX_UNI_CNT	0x00000200	/* Unicast TX Frames Sent */#define	TX_MULTI_CNT	0x00000400	/* Multicast TX Frames Sent */#define	TX_BROAD_CNT	0x00000800	/* Broadcast TX Frames Sent */#define	TX_EXDEF_CTL	0x00001000	/* TX Frames With Excessive Deferral */#define	TX_MACCTL_CNT	0x00002000	/* MAC Control TX Frames Sent */#define	TX_ALLF_CNT	0x00004000	/* All TX Frames Sent */#define	TX_ALLO_CNT	0x00008000	/* All TX Octets Sent */#define	TX_EQ64_CNT	0x00010000	/* 64-Byte TX Frames Sent */#define	TX_LT128_CNT	0x00020000	/* 65-127-Byte TX Frames Sent */#define	TX_LT256_CNT	0x00040000	/* 128-255-Byte TX Frames Sent */#define	TX_LT512_CNT	0x00080000	/* 256-511-Byte TX Frames Sent */#define	TX_LT1024_CNT	0x00100000	/* 512-1023-Byte TX Frames Sent */#define	TX_GE1024_CNT	0x00200000	/* 1024-Max-Byte TX Frames Sent */#define	TX_ABORT_CNT	0x00400000	/* TX Frames Aborted */#endif				/* _DEF_BF537_H */